Français dropdown-ico

Manuel d’utilisation AquaStar 125FX NG

24 pages 0.82 mb
Télécharger

Aller à la page of 24

Summary
  • AquaStar 125FX NG - page 1

    WARNING : Improper installation, adjustment , alt eration , service or maintenance can c ause injury or property damage. Refer to this manual. For assistance or additional information consult a qualified installer, service agency or t he gas supplier. Upon completion of the installation, these instructions should be handed to the user of the applia ...

  • AquaStar 125FX NG - page 2

    2 6 720 606 601 AquaSt ar 1 25FX LP and 1 25FX NG Specific ations W ater Connection 1 /2” Thread fitting N P T H x W x D 29 3/ 4” x 1 8 1 /4” x 8 3/4" V ent 4” Gas C onnection 1 /2” N PT thread Min. W ater Pressure 1 8 Psi Max. W ater Pressure 1 50 Psi Shipping W eight 50.6 LB Net W eight 44 LB 2.0 G PM at 90 ° rise 4.0 G PM at 45 ? ...

  • AquaStar 125FX NG - page 3

    3 6 720 606 601 M I N I M U M I N S T ALLA TI ON C LE AR A N C E S F R OM C O M B USTI B LE AN D N ON C OM B U S TI B LE MA TE R IALS F OR AL C O VE OR C L O SET I N S T ALLA TI ON S FR ONT VI EW SI D E VI EW A QUAST AR MO DE L 1 25FX * On a combustible wall surface the unit should be mounted away from the wall to provide adequate clearance of the ...

  • AquaStar 125FX NG - page 4

    4 6 720 606 601 G EN E RAL R U LES T O FOLL OW FOR SAFE O PE R A TI ON 1. Y ou should follow these instructions when you inst all your heater . In the United St ates: The installation must conform with local codes or , in the absence of local codes, the National Fuel Gas Code AN SI Z223. 1 / N FP A 54. In Canada: The Installation should conform wit ...

  • AquaStar 125FX NG - page 5

    5 6 720 606 601 COMBUSTION AIR REQUIREMENTS The AquaStar water heater holds cold water in its copper heat exchanger and brass water valve when not in use. Because of this, any cold air that comes in through the unit’s vent pipe is capable of freezing these components. This Installation Manual specifies the vent length requirements and the amount ...

  • AquaStar 125FX NG - page 6

    6 6 720 606 601 Fig . 3 - Inc andescent Part icle T ray Illust ration The incandescent particle tray (shipped loose in the carton with the water heater) must be attached at the bottom of the water heater front cover at the time of installation. Use the screws provided. See figure 3. SCREWS INCANDESCENT P ARTICLE TRA Y Fig. 2 - Mounting the Heater W ...

  • AquaStar 125FX NG - page 7

    7 6 720 606 601 VENTING WARNING: Do not reduce the vent pipe size and do not common vent with any other vented appliance or stove. This appliance must be vented horizontally to the outside with a sealed 4” single wall vent pipe. The appliance’s flue gasses are under positive pressure and must travel through a single wall 4” pipe that is seale ...

  • AquaStar 125FX NG - page 8

    8 6 720 606 601 Fig 4 : Some V ent ing Guide Suggestions An approved side wall vent terminal must be used when the water heater is vented through a side wall. Locate in accordance with AN SI Z223. 1 and local applicable codes . See Fig 5 for restrictions in location of vent terminal in relation to opening doors and windows, grade, and forced air in ...

  • AquaStar 125FX NG - page 9

    9 6 720 606 601 Fig 5: Side wall exit locations for mechanical draft vent terminals SOFFIT VENT HOOD 7’ MINIMUM ABOVE PUBLIC WALKWA Y ONE FOOT ABOVE GRADE 3’ ABOVE ANY FORCED AIR INLET WITHIN 10’ 4’ MIN 1’ MIN 4’ MIN 4’ MIN 4’ MIN 1’ MIN VENT HOOD MUST BE MOUNTED FOUR FEET A WA Y FROM DOORS AND WINDOWS VENT HOOD MUST BE MOUNTED FO ...

  • AquaStar 125FX NG - page 10

    10 6 720 606 601 Fig. 6 - Appliance pressure regulator (with directional arrow on reverse side pointing up) GAS LINE SIZING The pressure regulator provided with the heater is adjusted to deliver the proper gas pressure (as indicated on the rating plate and in the manual for altitude up to 2000 feet (660 meters) above sea level. On appliances being ...

  • AquaStar 125FX NG - page 11

    11 6 720 606 601 GAS PIPING, CONNECTIONS Before connecting the gas supply, c heck the rating plate on the right side of the front cover to be sure that the heater is rated for the same gas to which it will be connected. In the United St ates: T he installation must conform with local codes or, in the absence of local codes, the National Fuel Gas C ...

  • AquaStar 125FX NG - page 12

    12 6 720 606 601 Fig.7 - Water valve and water connectors, top view W A TE R CONN EC TIO N S Install the heater centrally in the building if possible and make hot water piping runs as short as possible When facing the heater , the cold water inlet will be on the right and the hot water outlet on the left.. Although water piping throughout the build ...

  • AquaStar 125FX NG - page 13

    13 6 720 606 601 ELECTRICAL CONNECTIONS WARNING: For safety reasons, disconnect the power supply to the heater before any service or testing is performed. WARNING: This heater must be electrically grounded in accordance with the most recent edition of the National Electrical Code , N FP A 70. In Canada , all electrical wiring to the heater should b ...

  • AquaStar 125FX NG - page 14

    14 6 720 606 601 O PERA T I N G INST R UC T ION S Before operating the heater , make sure that the system is filled with water. Open the cold water inlet supply to the heater fully . Open a hot water faucet to permit the water to fill the heater and the piping and to eliminate the air trapped in the system Close the hot water faucet after the water ...

  • AquaStar 125FX NG - page 15

    15 6 720 606 601 Fig. 1 2 - Charact eristic Pilot Flame Flame sensor Piezo Electrode W at e r V alve ( Part # 8 7 07 002802): The water valve on this heater should be serviced periodically. Lubricate component #36 on page 20 with a small amount of silicon, faucet or lithium grease every two years to keep its o rings fresh and pushrod sliding smooth ...

  • AquaStar 125FX NG - page 16

    16 6 720 606 601 3. W ater flow is not sufficient to act ivate heater. W ater flow rate at faucet is below minimum flow needed to activate heater . W hen temperature adjustment knob is turned all the way clockwise, the AquaStar model 1 25FX requires 1 /2 gallon per minute flow to activate the heater . As a reference, this is a flow which would fill ...

  • AquaStar 125FX NG - page 17

    17 6 720 606 601 Mineral deposits can eventually (3-5 years in hard water areas) corrode the water valve parts to a point where they will need replacing. Any sign of moisture at the bleed hole is a sign that the water valve needs to be replaced immediat ely . 1 0. Poor circuit connect ions at t he EC O ( overheat sensor ) or the flue gas safety dev ...

  • AquaStar 125FX NG - page 18

    18 6 720 606 601 WA TE R IS T OO H O T 1 . T emperature S election too high T urn the temperature adjustment knob counter-cloc kwise (to the left) to lower the maximum water temperature. Note: This will increase the activation flow rate. 2 . Inlet water temperature is very warm (60°-75°F) Reduce inlet gas supply to lower the heaters degree rise. ...

  • AquaStar 125FX NG - page 19

    19 6 720 606 601 Fig. 1 5 - Diagram of AquaStar 1 25FX 1 . Heat exchanger 2. Pilot assembly 3. Burner manifold gas pressure test nipple 4. Main gas burner 5. Pilot gas tubing 6. Gas valve 7. electric control box 8. Power cord 9. on/off switch 1 0. T emperature adjustment selector 1 1 . Microswitch 1 2. Gas inlet gas pressure test nipple 1 3. Exhaus ...

  • AquaStar 125FX NG - page 20

    20 6 720 606 601 Fig. 1 6 - I NTE RI OR CO MP ON E NTS DIA G RAM AN D P ARTS LIST ...

  • AquaStar 125FX NG - page 21

    21 6 720 606 601 Fig . 1 6 INTERIOR COMPONENTS DIAGRAM AN D P ARTS LIST 1 25FX 1 Cover 8 705 421 775 2T e m p era tur e ad j ustment kno b 8 702 000 111 3T e m p era tur e ad j ustment co l lar 8 700 403 008 4 Dra ft diverter 8 705 505 451 5 He at ex chan g er 8 705 406 235 6 Overheat se n sor (ECO) 8 707 206 040 7 Main burner 8 708 120 298 N G 7 M ...

  • AquaStar 125FX NG - page 22

    22 6 720 606 601 Fig . 1 7 - Flow chart of Aquastar 1 25 F X ...

  • AquaStar 125FX NG - page 23

    23 6 720 606 601 L I M ITE D W AR R ANT Y Aquast ar General Aquastar water heaters are warranted by the Manufacturer ( B OSC H ) through Controlled Energy C orp. C ontrolled Energy C orp. (C EC ) will furnish a replacement heat exchanger and will furnish a replacement of any other part which fails in normal use and service within the applicable per ...

  • AquaStar 125FX NG - page 24

    Replacement Parts available from North American Distributor CONTROLLED ENERGY CORP . 340 Mad River Park W ait sfield, V ermont 05673 Phone 800-642-31 1 1 Fax (802) 496-6924 ww w .controlledenergy .com/tech techsupport@controlledenergy .com VULCANO T ermodomésticos S.A. Estrada de Cacia 3801 - 856 Aveiro - PORTUGAL 5 1 e g a p e e s E L B A T E C N ...

Fabricant AquaStar Catégorie Water Heater

Les documents que nous recevons du fabricant de l'appareilAquaStar 125FX NG peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques AquaStar
- manuels d’utilisations 125FX NG
- fiches produit AquaStar
- dépliants
- ou étiquettes-énergie AquaStar 125FX NG
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation AquaStar 125FX NG.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation AquaStar 125FX NG, manuels d’entretien, brefs manuels ou manuels de l’utilisateur AquaStar 125FX NG. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit AquaStar 125FX NG.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil AquaStar 125FX NG, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser AquaStar 125FX NG par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs AquaStar 125FX NG.

Le manuel d’utilisation complet AquaStar, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel AquaStar 125FX NG - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières AquaStar 125FX NG, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAquaStar 125FX NG qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil AquaStar 125FX NG - qui devraient nous aider dans les premières étapes lors de l'utilisation AquaStar 125FX NG
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de AquaStar 125FX NG
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service AquaStar 125FX NG dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de AquaStar 125FX NG?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec AquaStar 125FX NG, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec AquaStar 125FX NG il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)