Manuel d’utilisation Hobart ML-104586

12 pages 0.47 mb
Télécharger

Aller à la page of 12

Summary
  • Hobart ML-104586 - page 1

    FP350 FOOD PROCESSOR MODEL FP350 ML-104586 FOOD PROCESSORS 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 19353 Rev. D (Oct. 2000) ...

  • Hobart ML-104586 - page 2

    – 2 – © HOBART CORPORATION, 1995 T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Hobart ML-104586 - page 3

    – 3 – Installation, Operation, and Care of MODEL FP350 FOOD PROCESSOR SA VE THESE INSTRUCTIONS GENERAL The FP350 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicing vegetables, fruits, or cheese. A worktable, a wall rack, and a wide range of slicer, shredder, and dicing plates are available options. INST ALLA TIO ...

  • Hobart ML-104586 - page 4

    – 4 – Fig. 1 ...

  • Hobart ML-104586 - page 5

    – 5 – OPERA TION WARNING : ROTATING KNIVES INSIDE. ALWAYS USE PUSHER PLATE. KEEP HANDS OUT . Proper assembly of the FP350, including selection of the appropriate cutters, is necessary for correct operation of the food processor. Refer to the Cutting Tool Guide for sizes of cutters and refer to the appropriate operation instructions. CONTROLS (F ...

  • Hobart ML-104586 - page 6

    – 6 – 3. To remove the pusher plate, hold the pusher plate handle, raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position. 4. Take hold of the pusher plate with both hands (Fig. 2). 5. Rotate pusher plate until the pin on the shaft is out of the slot on the bracket. Pull the pusher plate up and ...

  • Hobart ML-104586 - page 7

    – 7 – Removing the Cutting Tools 1. Using the pusher plate handle, raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position. 2. Turn the lock handle counterclockwise and swing the feed cylinder out to the right. 3. Using the wrench supplied, loosen the decoring screw in a clockwise direction. 4. ...

  • Hobart ML-104586 - page 8

    – 8 – CLEANING WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE CLEANING. Clean the machine immediately after each use. Dismantle all removable parts from the machine and wash them in warm water and detergent. Rinse thoroughly and wipe dry with a soft clean cloth. Allowing food juices to dry on the machine may cause discolor ...

  • Hobart ML-104586 - page 9

    – 9 – CUTTING TOOL GUIDE Fractional sizes are in inches (millimeters are in parentheses). Slicers Use Fine and Standard Slicers for sliced products and for dicing. Soft products like tomato - use the FINE SLICER, not the STANDARD SLICER. FINE SLICER 1 ⁄ 16 (1.5 mm) FINE SLICER 1 ⁄ 8 (3 mm) FINE SLICER 5 ⁄ 32 (4 mm) FINE SLICER 7 ⁄ 32 (6 ...

  • Hobart ML-104586 - page 10

    – 10 – Dicer and French Fry Plates The recommended slicer plate will produce near cube-shaped products. The DICER grid dimension must be equal to or larger than the SLICER dimension. DICER 9 ⁄ 32 (7.5 mm) Use with FINE SLICER 7 / 32 (6 mm), 5 ⁄ 32 (4 mm), 1 ⁄ 8 (3 mm), 1 ⁄ 16 (1.5 mm) * DICER 3 ⁄ 8 (10 mm) Use with STANDARD SLICER 3 / ...

  • Hobart ML-104586 - page 11

    – 11 – MAINTENANCE WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING ANY MAINTENANCE. Routinely inspect the machine to make sure that it is in proper working order. Plates must be clean, intact and sharp. The knife shaft should be regularly lubricated with a drop of mineral oil, NOT COOKING OIL. REPLACEMENT DICING GRIDS ...

  • Hobart ML-104586 - page 12

    – 12 – FORM 19353 Rev. D (Oct. 2000) PRINTED IN U.S.A. SERVICE Contact your local Hobart Service Office for any repairs or adjustments needed on this equipment. Long-term service contracts are available on this and other Hobart products. SYMPTOM POSSIBLE CAUSE SUGGESTED ACTION Low output or bad cutting results. A. B. C. D. E. Wrong cutting tool ...

Fabricant Hobart Catégorie Food Processor

Les documents que nous recevons du fabricant de l'appareilHobart ML-104586 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Hobart
- manuels d’utilisations ML-104586
- fiches produit Hobart
- dépliants
- ou étiquettes-énergie Hobart ML-104586
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Hobart ML-104586.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Hobart ML-104586, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Hobart ML-104586. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Hobart ML-104586.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Hobart ML-104586, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Hobart ML-104586 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Hobart ML-104586.

Le manuel d’utilisation complet Hobart, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Hobart ML-104586 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Hobart ML-104586, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHobart ML-104586 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Hobart ML-104586 - qui devraient nous aider dans les premières étapes lors de l'utilisation Hobart ML-104586
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Hobart ML-104586
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Hobart ML-104586 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Hobart ML-104586?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Hobart ML-104586, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hobart ML-104586 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)