Hobart ML-104586の取扱説明書

12ページ 0.47 mb
ダウンロード

ページに移動 of 12

Summary
  • Hobart ML-104586 - page 1

    FP350 FOOD PROCESSOR MODEL FP350 ML-104586 FOOD PROCESSORS 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 19353 Rev. D (Oct. 2000) ...

  • Hobart ML-104586 - page 2

    – 2 – © HOBART CORPORATION, 1995 T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Hobart ML-104586 - page 3

    – 3 – Installation, Operation, and Care of MODEL FP350 FOOD PROCESSOR SA VE THESE INSTRUCTIONS GENERAL The FP350 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicing vegetables, fruits, or cheese. A worktable, a wall rack, and a wide range of slicer, shredder, and dicing plates are available options. INST ALLA TIO ...

  • Hobart ML-104586 - page 4

    – 4 – Fig. 1 ...

  • Hobart ML-104586 - page 5

    – 5 – OPERA TION WARNING : ROTATING KNIVES INSIDE. ALWAYS USE PUSHER PLATE. KEEP HANDS OUT . Proper assembly of the FP350, including selection of the appropriate cutters, is necessary for correct operation of the food processor. Refer to the Cutting Tool Guide for sizes of cutters and refer to the appropriate operation instructions. CONTROLS (F ...

  • Hobart ML-104586 - page 6

    – 6 – 3. To remove the pusher plate, hold the pusher plate handle, raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position. 4. Take hold of the pusher plate with both hands (Fig. 2). 5. Rotate pusher plate until the pin on the shaft is out of the slot on the bracket. Pull the pusher plate up and ...

  • Hobart ML-104586 - page 7

    – 7 – Removing the Cutting Tools 1. Using the pusher plate handle, raise the pusher plate and swing it out to the left so that the feed cylinder is set in the open position. 2. Turn the lock handle counterclockwise and swing the feed cylinder out to the right. 3. Using the wrench supplied, loosen the decoring screw in a clockwise direction. 4. ...

  • Hobart ML-104586 - page 8

    – 8 – CLEANING WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE CLEANING. Clean the machine immediately after each use. Dismantle all removable parts from the machine and wash them in warm water and detergent. Rinse thoroughly and wipe dry with a soft clean cloth. Allowing food juices to dry on the machine may cause discolor ...

  • Hobart ML-104586 - page 9

    – 9 – CUTTING TOOL GUIDE Fractional sizes are in inches (millimeters are in parentheses). Slicers Use Fine and Standard Slicers for sliced products and for dicing. Soft products like tomato - use the FINE SLICER, not the STANDARD SLICER. FINE SLICER 1 ⁄ 16 (1.5 mm) FINE SLICER 1 ⁄ 8 (3 mm) FINE SLICER 5 ⁄ 32 (4 mm) FINE SLICER 7 ⁄ 32 (6 ...

  • Hobart ML-104586 - page 10

    – 10 – Dicer and French Fry Plates The recommended slicer plate will produce near cube-shaped products. The DICER grid dimension must be equal to or larger than the SLICER dimension. DICER 9 ⁄ 32 (7.5 mm) Use with FINE SLICER 7 / 32 (6 mm), 5 ⁄ 32 (4 mm), 1 ⁄ 8 (3 mm), 1 ⁄ 16 (1.5 mm) * DICER 3 ⁄ 8 (10 mm) Use with STANDARD SLICER 3 / ...

  • Hobart ML-104586 - page 11

    – 11 – MAINTENANCE WARNING : TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING ANY MAINTENANCE. Routinely inspect the machine to make sure that it is in proper working order. Plates must be clean, intact and sharp. The knife shaft should be regularly lubricated with a drop of mineral oil, NOT COOKING OIL. REPLACEMENT DICING GRIDS ...

  • Hobart ML-104586 - page 12

    – 12 – FORM 19353 Rev. D (Oct. 2000) PRINTED IN U.S.A. SERVICE Contact your local Hobart Service Office for any repairs or adjustments needed on this equipment. Long-term service contracts are available on this and other Hobart products. SYMPTOM POSSIBLE CAUSE SUGGESTED ACTION Low output or bad cutting results. A. B. C. D. E. Wrong cutting tool ...

メーカー Hobart カテゴリー Food Processor

Hobart ML-104586のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ML-104586の取扱説明書
- Hobartの製品カード
- パンフレット
- またはHobart ML-104586の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Hobart ML-104586の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Hobart ML-104586の取り付け説明書、サービスマニュアル、簡易説明書、またはHobart ML-104586のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Hobart ML-104586の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Hobart ML-104586デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHobart ML-104586を使用するのを助ける技術的文書のことです。説明書は通常、全てのHobart ML-104586ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Hobartの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Hobart ML-104586の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHobart ML-104586の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Hobart ML-104586に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Hobart ML-104586デバイスの基本機能を使うにあたってのヒント。 Hobart ML-104586のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Hobart ML-104586に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHobart ML-104586のメーカー/サービスへの連絡先に関する情報。

Hobart ML-104586についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHobart ML-104586の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHobart ML-104586で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)