Français dropdown-ico

Manuel d’utilisation John Deere OMM141979 J9

36 pages 6.59 mb
Télécharger

Aller à la page of 36

Summary
  • John Deere OMM141979 J9 - page 1

    OMM141979 J9 J9 Mechanical Tiller 30-Inch OPERA T OR’S MANU AL North Am erican V ersion Litho in U.S.A. ...

  • John Deere OMM141979 J9 - page 2

    Introduction INTR ODUCTION Introducti on Thank Y ou for Purc hasing This Product W e appreciate y our b usiness and wish y ou many y ears of saf e and satisfied use of y our machin e. Using Y our Operator ’ s Manual This manual is an im por tant par t of your machine and should remain with the machine when you sell it. Reading y our operator’ s ...

  • John Deere OMM141979 J9 - page 3

    Product Identifica tion PR ODUCT IDENTIFICATION Product I dentificat ion Recor d Identification Numbers Mechan ical Tiller 30-Inch Ser ial No . (010001 - ) If you need to contact an Authorized Ser vice Cen ter for inf orm ation on servicing, alwa ys provide the product model and ser ial number . Y ou will need to locate the identification n umber f ...

  • John Deere OMM141979 J9 - page 4

    T able o f Contents TA B L E O F C O N T E N T S All information, illustrations and specifications in this manual are based on the latest information at the time of publication. The right is reser ved to make changes at an y time without notice. COPYRIGHT© 1999 Deere & Co . John Deere Worldwide Commercial and Consumer Equipment Division Horico ...

  • John Deere OMM141979 J9 - page 5

    Saf ety - 1 SAFETY Safety Understanding The Machine Saf ety Labels The machine saf ety labels shown in this section ar e placed in impor tant areas on y our machine to dr aw atten tion to potential saf ety hazards. On y our machine saf ety labels , the words D ANGER, W ARNING, and CA UTION are used with this safety-aler t symbol, ( c ). D ANGER ide ...

  • John Deere OMM141979 J9 - page 6

    Saf ety - 2 SAFETY BEFORE DISMOUNTING OR SER VICING • Shut off engine and remov e key . • Lock br ake f or par k. • L o w e ro rb l o c ku pm a c h i n e . Operate Safel y • Chec k v ehicle brak e action bef ore you oper ate. Adjust or ser vice brakes as necessar y . • Inspect machine bef ore you o perate . Be sure hardw are is tight. Rep ...

  • John Deere OMM141979 J9 - page 7

    Saf ety - 3 SAFETY Practice Safe Maintenance • Underst and ser vic e procedure b ef ore do ing work . K eep area clean an d dr y . • Ne ver lubricate, service, or adjust machine while it is moving. K eep saf ety de vices in place and in working condition. Keep hardware tight. • K eep hands , f eet, clothing, je welry , and long hair a wa y fr ...

  • John Deere OMM141979 J9 - page 8

    Prepare V ehicle - 4 PREPARE V EHICLE Prepare V ehicle Remove Mo wer Deck T ractor mower dec k must be remov ed from bef ore installing tiller . See your tractor oper ator ’ s manual or mo wer deck manual f or remov al instr uctions. Ballasting Requirements All tractor s require front wheel weig hts to be installed when using this tiller . F ollo ...

  • John Deere OMM141979 J9 - page 9

    Installing - 5 INSTALLING Installi ng P ark V ehic le Safel y • Stop v ehicle on a le v el surf ace, not on a slope . • Disengag e PT O . • Engage the park brak e. • ST OP the engin e. • Remo ve th e ke y . • Bef ore you lea v e the operator ’ s seat, wait for engine and all moving par ts to STOP . Setting Depth Contr ol Knob T urn de ...

  • John Deere OMM141979 J9 - page 10

    Installing - 6 INSTALLING handle (B) to rotate tiller housing while pulling left frame rail upward s to gain clearance to l ower fr ame wheels (C). 2. Unlock loc king pin (D) and rotate frame wheel do wn into engaged position and make sure loc king pin locks into loc king hole. Loc k r ight frame wheel d own into eng aged position in similar fashio ...

  • John Deere OMM141979 J9 - page 11

    Installing - 7 INSTALLING Disengage Frame Suppor t Rod 1. Mov e to left side, under tr actor f ootrest — hold lift handle (B) down. 2. Piv ot suppor t rod (C) down in to storage position. 3. Slowly release do wnw ard pressure on lift handle (B) until cups of tiller frame latches (A) are seated up against mounting pins (D). F asten Frame Clip Latc ...

  • John Deere OMM141979 J9 - page 12

    Installing - 8 INSTALLING tiller lift rod (B) upright, align tractor lift link (A) so pin (C) fits into hole (D) of lift link (A). 2. Install M13 x 24 x 2.5 mm w asher (E), from bag of parts, on lift rod pin (C). 3. F asten lift rod to lift link with spring locking ring (F), from bag of par ts. Adjust Tiller Lift Height 1. Push implement lift le ve ...

  • John Deere OMM141979 J9 - page 13

    Removing - 9 REMO VING Removing P ark V ehic le Safel y • Stop v ehicle on a le v el surf ace, not on a slope . • Disengag e PT O . • Engage the park brak e. • ST OP the engin e. • Remo ve th e ke y . • Bef ore you lea v e the operator ’ s seat, wait for engine and all moving par ts to STOP . Mo ve Implement Lift Lever 1. Pull impleme ...

  • John Deere OMM141979 J9 - page 14

    Removing - 10 REMO VING Disengage Belt And Unhook Left Clip Latch 1. Mov e to r ight side , under tractor f ootrest — mov e belt tensioning idler lev er (A) out of “ ENGAGED ” position into “ DISENGA GED ” position (point ing toward front of tractor). 2. Pull and hold tensioning idler (B) towards right frame while you remo ve belt from PT ...

  • John Deere OMM141979 J9 - page 15

    Removing - 11 REMO VING Lock Frame Wheels Into Engage P osition 1. Mov e to left rear , behind tractor dr ive wheels — pull and hold out wheel locking p in (A). 2. Swing left wheel assembly ( B) down into “ ENGA GE ” position. Mak e sure loc king pin engages hole in loc king brac ket. Repeat f or r ight frame wheel. Disengage Frame Suppor t R ...

  • John Deere OMM141979 J9 - page 16

    Operating - 12 OPERATING Operating Tilling Tips Install correct front and rear tractor w eights. See Install W eights and Chains in Installing the Tiller section. Till with engine at F AST thrott le, control g round speed with appropriate transmission spe ed range. Check tines bef ore you till. Replace missing, bent, or brok en tines . When y ou ti ...

  • John Deere OMM141979 J9 - page 17

    Operating - 13 OPERATING Move Implement to “ RAISE ” P osition 1. First push implement lift le v er (A) f orward slightly , then depress and hold do wn button (B) to unlo ck lift le ver loc king mechanism. 2. Pull lift lev er reward out of “ LOWER ” po sition, release button (B) and continue to pull lev er all-the-way re ward until a loud m ...

  • John Deere OMM141979 J9 - page 18

    Operating - 14 OPERATING 3. Mov e to r ight side, below tractor f ootrest — rem ov e spring locking ring (A) and flat washer (B) f or m lift rod pin (C). 4. Remov e lift rod (D) f or m tractor lift link (E). NO TE: Maximum tilling depth is 150 mm (6-in.) — bottom of shaft to bottom edge of lo west tine. Picture Note: Tiller frame removed from t ...

  • John Deere OMM141979 J9 - page 19

    Operating - 15 OPERATING 2. Mov e to left side of tiller housing — grasp han dle (C) to raise tiller housing to remov e pressure on transpor t locking pin (D) and continue to hold tiller housing stationary while yo u pull transport locking pin (D) out and r otate it f orward into “ LOCK-OUT ” p o s i t i o n ,r o l l e dp i n( E )l o c k e di ...

  • John Deere OMM141979 J9 - page 20

    Operating - 16 OPERATING mechanism. 2. Pull lift le v er (A) rew ard out of “ LO WER ” position ( s h o w n ) ,r e l e a s eb u t t o n( B )a n dc o n t i n u et op u l ll e v e ra l l - the-wa y rew ard until a loud metalli c-clic k is heard, signalling lev er is in “ LOCK-OUT ” position, then release lift le ver — it is no w lock ed int ...

  • John Deere OMM141979 J9 - page 21

    Ser vice - 17 SERVIC E Service Service Intervals Checking Belt T ension Picture Note: Tiller removed for c larity purposes only . 1. Chec k position of belt ten sion rod (A): • If rod end is in po sition (B), against the v er tical frame rail (C), the belt i s too tight and m ust be loosened. • If rod end is in position (D ), e xtend s bey ond ...

  • John Deere OMM141979 J9 - page 22

    Ser vice - 18 SERVIC E Cleaning Under Belt Shield Picture Note: Tiller removed for c larity purposes only . 1. Mov e to left side of tiller housing — remove two self- tapping cap screws (A) and belt shield (B). 2. Clean dir t from sheave and surrounding area . 3. Install shield ( B) and self-tapp ing cap screws (A) until snug — DO NO T ov er-ti ...

  • John Deere OMM141979 J9 - page 23

    Ser vice - 19 SERVIC E 2. Loosen flang e lock n ut (A) on tensioning idler . Move be lt guide (B) awa y from belt. 3. Loosen top jam nuts (C), o ne on each side, to tilt guide bolts (D) aw ay from drive shea ve. 4. Remove belt. Install Primary Drive Belt 1. Install belt on d rive shea ve with wide- edge of belt f acing guide bolts (D). 2. Tighten t ...

  • John Deere OMM141979 J9 - page 24

    Ser vice - 20 SERVIC E 7. Remov e secondary b elt (K) from tiller drive shea ve . Install Secondary Drive Belt 1. Install ne w secondar y dr iv e belt with one twist (A), as shown, to seat “ V ” of belt in secondary drive shea v e (B). DO NO T cross-ov er belt (f or ming an “ X ” patter n) when installing or tiller drive rotation will be re ...

  • John Deere OMM141979 J9 - page 25

    Ser vice - 21 SERVIC E 2. Raise tiller as high as it will go if still on tractor . NO TE: For ease in replacing tines, yo u can remove tiller fr om the tractor an d turn it completel y upside down. Put do wn prote ctive tarp or carpet to pr otect paint finish. 3. Put tiller in TRANSPOR T position. (See T ranspor ting Tiller in OPERA TING section.) ...

  • John Deere OMM141979 J9 - page 26

    Ser vice - 22 SERVIC E • MiddleTine Sets : Remo v e lock nut s (A), bolts (B), spacers (C), t wo left tines (D), and two right t ines (E). Remember to inst all ne w bolts so heads a re to left side and ne w lock n uts are to right side . A total of eight spacers are used in these middle tine sets — fo u r i n e a c h set. • Right Tine Set : R ...

  • John Deere OMM141979 J9 - page 27

    T roubl eshooting - 23 T R OUBLESHOOTING Troubleshooting Using T roub leshooting Char t If yo u are ex periencing a problem that is n ot listed in this char t , see your authorized dealer for ser vice. W h e ny o uh a v ec h e c k e da l l t h ep o s s i b l ec a u s e sl i s t e da n d yo u are still e xperiencing the prob lem, see you r authorize ...

  • John Deere OMM141979 J9 - page 28

    Stor age - 24 STORAGE Storage Storing Tiller 1. Remo v e tiller from tr actor . (See the REMO V ING section.) 2. Clean tiller with water pressure. 3. Chec k belts. If necessary , get ne w belts from your A uthorized Service Center . DO NOT in stall the ne w belts until you tak e tiller out of storage . 4. Replac e or repair badly wor n or da maged ...

  • John Deere OMM141979 J9 - page 29

    Assembly - 25 ASSEMBL Y Assembly Identify Parts – 30 Inch Mechanical Tiller Bag of P arts M96256 B C D E F G H L I O K J A M96254 M N P Q Qty . Us ed P ar t Description Size 1 Handle, L ift (A) 2 Pin, Mounting (B) 1 Sheav e, Idler (C) 1 Guide, Belt (D) 2 Bolt, Flange (E) M12 x 1.75 x 50 mm 2 Bolt, Flange ( F) M6 x 1.00 x 30 mm 4 Bolt, He x (G) M8 ...

  • John Deere OMM141979 J9 - page 30

    Assembly - 26 ASSEMBL Y Install T ractor Rear -Frame Hard ware 1. F rom bag of part s, in stall one spacer (A ) on each M12 x 1.75 x 50 mm flange bolt (B). 2. Install spa cers and bolts in BO TT OM holes at rear of tractor fr ame and secure with M12 x 1.7 5 lockn uts (C) on inside of tractor frame. Tighten locknuts to 105 N • m (78 ft- lb). Insta ...

  • John Deere OMM141979 J9 - page 31

    Assembly - 27 ASSEMBL Y Put Tiller Frame Rails In T ransport Position 1. Pull left frame rail up until locking pin (A) can be loc ked into locking br ack et hole. Push do wn on tiller handle (B) to rotate tiller housing while pulling left frame rail up to gain clearance to lo wer left frame wheel. 2. Unlock loc king pin (C) and rotate wheel down in ...

  • John Deere OMM141979 J9 - page 32

    Assembly - 28 ASSEMBL Y NO TE: Make sure belt guide does not mo ve out of position when tighte ning lock nut. 6 . T i g h t e nM 8x1 . 2 5l o c k n u tt o4 0N • m (354 lb-in.). 7. After tightening, mak e sure the idler shea v e rotates freely on the tens ioning ar m. 8. Pull the belt tight and mak e sure belt guide doe s not contact idler shea ve ...

  • John Deere OMM141979 J9 - page 33

    Specifications - 29 SPECIFICATIONS Specific ations Tiller Speci fications Tiller Specifications Dimensions: C u t t i n gW i d t h ................ ................ ............. ................ .......... 7 6 2m m ( 3 0 - i n . ) M a x i m u mC u t t i n gD e p t h ............... ............. ................ ................ ... 1 5 0m m ( 6 - ...

  • John Deere OMM141979 J9 - page 34

    Inde x - 30 INDE X Index B Ballasting Requirements .........................................4 Before Tilling ........................................................12 Belt Shield, Cleaning Under .................................18 Belt Tension, Checking .........................................17 Belt, Disengage ................................... ...

  • John Deere OMM141979 J9 - page 35

    Notes - 31 NOTES Notes ...

  • John Deere OMM141979 J9 - page 36

    Quality Sta tement - 32 QUALITY STATEMENT Quality Stateme nt Y our product , designed and built b y John Deere, is more than just a purchase , it ’ s an inv estment in quality . That quality goes be y ond our equipment to y our dealer ’ sp a r t s and service suppor t. That ’ s wh y John Deere has initiated a process to ha ndle yo ur question ...

Fabricant John Deere Catégorie Tiller

Les documents que nous recevons du fabricant de l'appareilJohn Deere OMM141979 J9 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques John Deere
- manuels d’utilisations OMM141979 J9
- fiches produit John Deere
- dépliants
- ou étiquettes-énergie John Deere OMM141979 J9
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation John Deere OMM141979 J9.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation John Deere OMM141979 J9, manuels d’entretien, brefs manuels ou manuels de l’utilisateur John Deere OMM141979 J9. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit John Deere OMM141979 J9.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil John Deere OMM141979 J9, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser John Deere OMM141979 J9 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs John Deere OMM141979 J9.

Le manuel d’utilisation complet John Deere, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel John Deere OMM141979 J9 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières John Deere OMM141979 J9, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lJohn Deere OMM141979 J9 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil John Deere OMM141979 J9 - qui devraient nous aider dans les premières étapes lors de l'utilisation John Deere OMM141979 J9
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de John Deere OMM141979 J9
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service John Deere OMM141979 J9 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de John Deere OMM141979 J9?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec John Deere OMM141979 J9, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec John Deere OMM141979 J9 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)