-
Bush Hog RDTH 84 - page 1
OPERATION l l MAINTENANCE 1107 $4.00 50038342 R D T H 8 4 R e a r D i s c h a r g e T u rf H o g O p e r a t o r ’ s M a n u a l B U S H H O G ® ...
-
Bush Hog RDTH 84 - page 2
CONGRA TULA TIONS! Y ou have invested in the best implement of its type on the market today . The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life. We urge a careful study of this manual to provide you with a thorough understanding of your new implement before operating, as wel ...
-
Bush Hog RDTH 84 - page 3
RDTH 84 Operator ’ s Manual T ABLE OF CONTENTS SECTION/P ARA P AGE W arranty ....................................................2 Dealer Preparation Check List ..................3 Safety Signs ..............................................4 Safety Precautions ....................................5 Federal Laws and Regulations ..................6 ...
-
Bush Hog RDTH 84 - page 4
LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an author-ized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state, and municipalities’ use and ninety (90) days for comm ...
-
Bush Hog RDTH 84 - page 5
DEALER PREP ARA TION CHECK LIST RDTH ROT AR Y CUTTER BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator ’s Manual as a guide. ❒ 1. Assembled completed. ❒ 2. Gearbox filled with oil. ❒ 3. All fittings lubricated. ❒ 4. All shields in place and in good condition. ❒ 5. All fasteners torqued to speci ...
-
Bush Hog RDTH 84 - page 6
Safety Alert Symbol This Safety Alert Symbol means: “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” This symbol is used to call attention to safety precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safe- ty pre ...
-
Bush Hog RDTH 84 - page 7
IMPORT ANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury. In addition to the design and ...
-
Bush Hog RDTH 84 - page 8
IMPORT ANT FEDERAL LA WS AND REGULA TIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERA TIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. Public Law 91-596 (The Williams-St ...
-
Bush Hog RDTH 84 - page 9
1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your RDTH Series Rotary Cutter has been carefully designed to give maximum service with minimum down time.This manual is provided to give you the necessary operating and maintenance instructions for keeping your rotary cutter in top operating condition. Please read this manual th ...
-
Bush Hog RDTH 84 - page 10
2-1 A TT ACHING TO TRACT OR A. Attach to tractor Cat. I three point hitch as described in tractor operator’s manual. B. Raise and lower cutter to determine position with shortest distance between the tractor PTO shaft and gearbox input shaft. Shut down tractor leaving cutter in position of shortest distance. SECURELY BLOCK CUTTER IN POSITION. C. ...
-
Bush Hog RDTH 84 - page 11
G. Clamp end of driveline in a vice. Cut off shield where marked. (Figure 2-3). Figure 2-3 H. Using cut off section of shield as a guide, cut shaft the same amount. (Figure 2-4) I. Repeat steps “G” and “H” to other driveline sec- tion. J. Deburr ends of driveline sections and clean away all chips and filings. (Figure 2-5) K. Apply multi-pur ...
-
Bush Hog RDTH 84 - page 12
SECTION III OPERA TING INSTRUCTIONS 3-1 GENERAL SAFETY Only qualified people familiar with this operator’s manual and tractor operator’s manual should oper- ate this machine. Operator should wear hard hat, safety glasses and safety shoes. The operator should read, understand and practice all safety mes- sages shown on the caution, warning and d ...
-
Bush Hog RDTH 84 - page 13
SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below. Lower implement to ground, turn off tractor, and set parking brake before doing maintenance inspections or work. Some checks may require raising machine off ground and supporting with blocks. All bolts should be torqued as indicated in torque chart un ...
-
Bush Hog RDTH 84 - page 14
Belt tension should be checked every 40 hours to get maximum life from drive belt and best perfor- mance from cutter. Belt tension is adjusted by increasing or decreasing the length of the spring on the moveable idler. For proper belt tension the spring length should be set at 2-7/8”. (Figure 4-2). To adjust the spring length, loosen or tighten t ...
-
Bush Hog RDTH 84 - page 15
4-6 TROUBLESHOOTING Troubleshooting procedures are listed in Table 4-1 below. If the problem cannot be solved or replacement parts are necessary, contact your authorized Bush Hog dealer. Please have ready your machine name, model number, serial number, purchase date and exact cause or description of problem. Table 4-1 Troubleshooting PROBLEM PROBAB ...
-
Bush Hog RDTH 84 - page 16
THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear personal protective equipment such as, but not limited to, protection for eyes, ears, feet, hands, lungs and head when assembling the equip- ment. Do not wear loose clothing or jewelry that may catch on equipment moving parts. 2. Do not lift ...
-
Bush Hog RDTH 84 - page 17
E. Fasten mast supports and upper flex link to mast halves using 5/8” x 5-1/2” bolt, pivot tube, lock- washer and locknut. F. Place two 1” spacers on the caster stems and insert into caster arms. Place two 1” spacers and one 1/2” spacers on the caster stem above the cast- er arms. This arrangement will give a cutting height of approximate ...
-
Bush Hog RDTH 84 - page 18
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more inform ...
-
Bush Hog RDTH 84 - page 19
T ORQUE SPECIFICA TIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15) ...
-
Bush Hog RDTH 84 - page 20
P.O. Box 1039 l l Selma, AL 36702-1039 Telephone (334) 874-2700 l l www.bushhog.com ...
Avez-vous une question à propos de Bush Hog RDTH 84?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Bush Hog RDTH 84, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Bush Hog RDTH 84 il est probable qu’il a envie de partager la façon de le résoudre.