Manuel d’utilisation Robertshaw 8625

12 pages 0.32 mb
Télécharger

Aller à la page of 12

Summary
  • Robertshaw 8625 - page 1

    1 Application The Robertshaw 8625 is a multi-stage thermostat designed to control 24 V AC heat pump systems. Features • Large back lit display . • Four preprogrammed E NERGY S TA R ® setpoints for each day of the week. • Adjustable 1 st stage temperature differential: 1.0°F to 3.0°F (0.5°C to 1.5°C). • Adjustable 2 nd stage temperature ...

  • Robertshaw 8625 - page 2

    IMPORT ANT SAFETY INFORMA TION WARNING: • Always turn off power at main fuse or circuit breaker panel before installing, removing, cleaning, or servicing thermostat. • Read all the information in this manual before installing this thermostat. • DO NOT CONNECT TO 120 V AC. This is a 24 V AC low-voltage thermostat. Do not install on voltages hi ...

  • Robertshaw 8625 - page 3

    IMPORT ANT SAFETY INFORMA TION WARNING: In heat pump applications, do not connect anything to the W1 terminal. When switched to HP mode, W1 is connected internally to Y1 on the thermostat. Connect AUX heat to the W2/E terminal. 1. T urn off power to heating and cooling system. 2. Remove cover of old thermostat to expose wires. Do not disconnect wir ...

  • Robertshaw 8625 - page 4

    6. Mark placement of mounting holes (see Figure 3). Set base aside. 7. Drill the marked holes using a 3/16” (5mm) drill bit. NOTE: Enclosed plastic anchors do not require a drilled hole for drywall. 8. T ap plastic anchors into the wall. 9. Align base with plastic anchors and feed wires through opening (see Figure 3). 10. Secure base to wall with ...

  • Robertshaw 8625 - page 5

    Wiring Diagrams The following is just a sample of the most common types of HV AC systems. Refer to your system’ s installation manual for wiring information. 5 Hot Heating Control Cooling Control Transformer T H E R M O S T A T W1 C R Y1 G O B 24 VAC 120 VAC Hot Heating Control Fan Control Transformer 24 VAC 120 VAC Hot Heating Control Transforme ...

  • Robertshaw 8625 - page 6

    6 T o T est Thermostat WARNING: DO NOT SHORT (JUMPER) ACROSS TERMINALS OF GAS V AL VE OR SYSTEM CONTROL TO TEST OPERA TION. THIS WILL DAMAGE THE THERMOST A T AND VOID YOUR W ARRANTY . CAUTION: DO NOT SWITCH SYSTEM TO COOL IF THE TEMPERA TURE IS BELOW 50°F (10°C). THIS CAN DAMAGE THE AIR CONDITIONING SYSTEM AND CAUSE PERSONAL INJURY . 1. Place the ...

  • Robertshaw 8625 - page 7

    Programming Guide SETTING TIME OF DA Y AND DA Y OF WEEK 1. Press SELECT until the cursor is over SET CLOCK. Press SET . The HOURS segment will be blinking. Use the or button to adjust the time. NOTE: The AM or PM indicator will change as the HOURS display rolls through a 24 hour cycle. 2. Press SET . The MINUTES segment will be blinking. Use the or ...

  • Robertshaw 8625 - page 8

    6. After pressing SET for the 4th event, the day of the week along the top will switch to SA T SUN and AM1 will be displayed. Repeat steps 2-4 to program the weekend settings. 7. With the weekend settings programmed, place the HEA T -OFF-COOL switch in the COOL position. Repeat steps 2-6 to program the cooling settings. CUSTOMIZING THE THERMOST A T ...

  • Robertshaw 8625 - page 9

    6. Press SET . The display will switch to the differential setting for 2 nd stage heating and cooling. 7. The display will read diF2 . Press the or button to adjust the differential up or down. 8. Press SET . The display will switch to the differential delay . 9. The display will read dL Y2 . The differential delay is the length of time (in minutes ...

  • Robertshaw 8625 - page 10

    Another way to select a temporary hold is: 1. Press SELECT until the cursor is over TEMP HOLD. Press SET . The temperature will be blinking. Use the or button to change the temperature. 2. Press SET . T o cancel a temporary hold, press SELECT until the cursor is above RUN/SET PROG. Press SET . Vacation Hold Y ou can set your thermostat to hold a de ...

  • Robertshaw 8625 - page 11

    T roubleshooting Symptom Remedy Thermostat does not turn Check wiring. on system. (See Installing Item 8625 Thermostat ) Thermostat turns on and off too Increase temperature differential. frequently . (See Programming Guide ) System fan does not operate Move the Electric/Gas switch to properly . either gas or electric, to match system. (See Install ...

  • Robertshaw 8625 - page 12

    12 ©2004 Climate Controls Americas 110-1101 Climate Controls Americas 191 E. North Avenue Carol Stream, Illinois 60188 United States of America TWO-YEAR LIMITED W ARRANTY Climate Controls Americas warrants to the original contractor installer or to the original consumer user , each new Robertshaw thermo- stat to be free from defects in materials a ...

Fabricant Robertshaw Catégorie Thermostat

Les documents que nous recevons du fabricant de l'appareilRobertshaw 8625 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Robertshaw
- manuels d’utilisations 8625
- fiches produit Robertshaw
- dépliants
- ou étiquettes-énergie Robertshaw 8625
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Robertshaw 8625.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Robertshaw 8625, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Robertshaw 8625. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Robertshaw 8625.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Robertshaw 8625, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Robertshaw 8625 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Robertshaw 8625.

Le manuel d’utilisation complet Robertshaw, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Robertshaw 8625 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Robertshaw 8625, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lRobertshaw 8625 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Robertshaw 8625 - qui devraient nous aider dans les premières étapes lors de l'utilisation Robertshaw 8625
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Robertshaw 8625
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Robertshaw 8625 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Robertshaw 8625?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Robertshaw 8625, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Robertshaw 8625 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)