Français dropdown-ico

Manuel d’utilisation Vermont Casting SNV30

32 pages 1.6 mb
Télécharger

Aller à la page of 32

Summary
  • Vermont Casting SNV30 - page 1

    INST ALLER / CONSUMER SAFETY INFORMA TION 20007067 1/07 Rev . 8 PLEASE READ THIS MANUAL BEFORE INST ALLING AND USING APPLIANCE. W ARNING! IF THE INFORMA TION IN THIS MANUAL IS NOT FOLLOWED EXACTL Y , A FIRE OR EXPLOSION MA Y RESUL T CAUSING PROPERTY DAMAGE, PERSONAL INJUR Y OR LOSS OF LIFE. FOR YOUR SAFETY Installation and service must be performed ...

  • Vermont Casting SNV30 - page 2

    2 2 Sta r dan ce N atur al V e nt G a s H eater 20007067 PLEASE READ THE INST ALLA TION & OPERA TING INSTRUCTIONS BEFORE USING APPLIANCE. Thank you and congratulations on your purchase of a V ermont Castings stove. IMPORT ANT : Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may re ...

  • Vermont Casting SNV30 - page 3

    3 Sta r dan ce N atur al V e nt G a s H eater 20007067 The Stardance Natural V ent Room Heater , Model Nos. 3980- 3996 is a vented gas appliance listed to the ANSI standard Z21.88b-2002 and CSA-2.33b-2002 for V ented Room Heaters, and CSA 2.17-M91, Gas-Fired Appliances For Use at High Al - titudes. The installation of the Stardance Natural V ent Ro ...

  • Vermont Casting SNV30 - page 4

    4 4 Sta r dan ce N atur al V e nt G a s H eater 20007067 9" (229mm) C L V alve Inlet 26  " (680 mm) 25" (635 mm) 14  " (355 mm) 3" (76 mm) C L 7067 Stardance fully assembled dimensions 12/22/03 djt V alve Inlet See Page 5 for Flue Collar Centerline Dimensions. 4406 Fig. 1 Stardance dimensions. Stardance Na ...

  • Vermont Casting SNV30 - page 5

    5 Sta r dan ce N atur al V e nt G a s H eater 20007067 Clearance Requirements Minimum Clearances to Combustible Materials Measure side clearances as shown in Figures 2 through 5 from the outer edge of the cast iron stove top. Measure rear clearances from the outermost surface of the sheet metal rear skirt. The Stardance heater is approved for insta ...

  • Vermont Casting SNV30 - page 6

    6 6 Sta r dan ce N atur al V e nt G a s H eater 20007067 V enting Requirements and Options The Stardance must be properly connected to a listed 4” (102 mm) T ype B venting system or to an approved Class A masonry or factory-built chimney system. In Canada, a complete relining of Class A chimney sys- tems is required. The Stardance Natural V ent s ...

  • Vermont Casting SNV30 - page 7

    7 Sta r dan ce N atur al V e nt G a s H eater 20007067 Passing Through a Combustible W all or Ceiling An approved pass-through device is always required when a vent passes through a combustible wall or ceil- ing. Check with the maker of the vent system for the correct listed devices that are available. A listed pass- through device is required whet ...

  • Vermont Casting SNV30 - page 8

    8 8 Sta r dan ce N atur al V e nt G a s H eater 20007067 ST640 RUVSOD snapstat 7/01 Snapstat Bracket Snapstat Module Pinch Grommet to Remove ST670 Fig. 9 Remove the snapstat and grommet from the bracket 4. Connect snapstat leads. Disconnect the snapstat module from the leads inside the snapstat bracket. (Fig. 9) Bend open the snapstat bracket. U ...

  • Vermont Casting SNV30 - page 9

    9 Sta r dan ce N atur al V e nt G a s H eater 20007067 ST194 attach fan to shroud 1 1/99 Outer Shroud Slot Inner Shroud Slot ST194 Fig. 10 Position the fan to engage the inner shroud with the fan bracket slots and secure with sheet metal screws. ST347a JUV FK28  rheostat install 9/21/00 Retaining Nut Control Knob ST347a Fig. 12 Attach r ...

  • Vermont Casting SNV30 - page 10

    10 10 Sta r dan ce N atur al V e nt G a s H eater 20007067 Insert the B-vent adapter into the flue collar and drill 1/8” (3mm) pilot holes through both the stove’s collar and the adapter . Attach the adapter to the flue collar with sheet metal screws. (Fig. 15) Attach the first section of venting to the B-vent adapter . Depending on the leng ...

  • Vermont Casting SNV30 - page 11

    1 1 Sta r dan ce N atur al V e nt G a s H eater 20007067 Burner Information The appliance must only use the gas specified on the rating plate, unless converted using a Fuel Conversion Kit. Refer to Page 25 for the correct Fuel Conversion Kit for your model. Conversion instructions are provided with each kit and beginning on Page 16 in this manual. ...

  • Vermont Casting SNV30 - page 12

    12 12 Sta r dan ce N atur al V e nt G a s H eater 20007067 Install the Front Plate Hold the front plate by the window bars and lift it into position, engaging the two steel tabs on the top corners behind the adjacent bosses in the side plates. (Fig. 21) Then seat the Front against the sides so the tabs at the bottom lip engage with the notches in t ...

  • Vermont Casting SNV30 - page 13

    13 Sta r dan ce N atur al V e nt G a s H eater 20007067 Fig. 22 T o open the front doors, turn handle clockwise. ST261 Stardance operable doors 1/31/01 Clockwise to Open Counterclockwise to Close ST624 The Stardance is operated with the operable door front plate in place with the doors open or closed. T o open the front doors, insert the handle ...

  • Vermont Casting SNV30 - page 14

    14 14 Sta r dan ce N atur al V e nt G a s H eater 20007067 3. Open control access panel. 4. Push in gas control knob slightly and turn clock- wise to “OFF”. Do not force. 5. Close control access panel. 1. STOP! Read the safety information above. 2. Turn of f all electrical power to the fireplace. 3. For MN/MP/TN/TP appliances ONL Y , go on to ...

  • Vermont Casting SNV30 - page 15

    15 Sta r dan ce N atur al V e nt G a s H eater 20007067 A. Defective or misaligned Using a match, light [ilot. If pilot lights, turn off pilot and electrode at the pilot push the ignitor button again. If pilot will not light, check gap at electrode and pilot - it should be 1/8” to have a strong spark. B. Defective ignitor (push Push piezo ignitor ...

  • Vermont Casting SNV30 - page 16

    16 16 Sta r dan ce N atur al V e nt G a s H eater 20007067 Conversion Precautions Conversion must be completed only by qualified personnel. Before proceeding, turn control knob on valve to OFF and turn gas supply OFF . T urn OFF any electricity that may be going to the appliance. CAU- TION: Allow stove to cool completely before beginning conversio ...

  • Vermont Casting SNV30 - page 17

    17 Sta r dan ce N atur al V e nt G a s H eater 20007067 FC107 SIT820 valve conversion 10/03 A B C O F F P I L O T O Fig. 30 Remove mounting screws, pressure regulator tower and spring and diaphragm assembly . FC107 D E F FC108 SIT regulator conversion 10/03 O F F P I L O T O FC108 Fig. 31 Replace regulator . 3. Install the enclosed conversion label ...

  • Vermont Casting SNV30 - page 18

    18 18 Sta r dan ce N atur al V e nt G a s H eater 20007067 17. Replace burner . Slide the burner in at an angle with left side lower than the right side. Slide the left side onto the injectors, making sure the burner leg remains at a 90° angle to the base. Lower the right hand side down in to place. Make sure the burner is as far left as possible ...

  • Vermont Casting SNV30 - page 19

    19 Sta r dan ce N atur al V e nt G a s H eater 20007067 Maintenance Y our Stardance Gas Heater will provide years of service with minimal upkeep. The following procedures will help ensure that your stove continues to function properly . Annual System Inspection Have the entire heater and venting system inspected annually by a qualified gas technic ...

  • Vermont Casting SNV30 - page 20

    20 20 Sta r dan ce N atur al V e nt G a s H eater 20007067 Gasket Replacement The Stardance Gas Heater uses a ‘tadpole’ type gasket to seal between the glass panel and the frame. In time, this gasket can become brittle and compressed and should be replaced. New gasket is available from your dealer . Shut off the gas supply and allow the stove t ...

  • Vermont Casting SNV30 - page 21

    21 Sta r dan ce N atur al V e nt G a s H eater 20007067 NOTE: IF ANY OF THE ORIGINAL WIRE, AS SUP- PLIED WITH THE APPLIANCE, MUST BE RE- PLACED, IT MUST BE REPLACED WITH TYPE SF-2, 200°C WIRE OR ITS EQUIV ALENT . ST665 Fig. 42 Safety Limit Switch wiring.  Ther m ocoupl e Safety Limit Switch Valve ST665 Safety Limit Switch wiring 5/29/01 djt ...

  • Vermont Casting SNV30 - page 22

    22 22 Sta r dan ce N atur al V e nt G a s H eater 20007067 1a 1b 1c PILOT ON OFF PILOT ADJ L O H I 3 5 6 7 20 8a,b 18 4 9a,b 17 19 7067 Stardance NV fully assembled parts 1 1/20/03 djt 23 24 22 a,b,c,d 25 27 21 28 26 30 31 32 2 29 1 1 12 15 10 13 14 16a,b 35 33 34 36 37 38 39 40 42a,b 43 CFM Corporation reserves the right to make changes in design, ...

  • Vermont Casting SNV30 - page 23

    23 Sta r dan ce N atur al V e nt G a s H eater 20007067 Stardance Natural V ent Gas Heater (SNV30) (continued) Models 3980-3996 4. Lava Rock - Burner 57897 5. Gasket, Glass Med. Knit - RDV40 1203702 6. Glass, DV25 1601691 7. Glass Frame Assembly SDV30 30000127 8a. V alve RN Honeywell VS8420E 2038 (Serial #’s up to 6361)* 10001782 8b. V alve RP Ho ...

  • Vermont Casting SNV30 - page 24

    24 24 Sta r dan ce N atur al V e nt G a s H eater 20007067 Stardance Natural V ent Gas Heater (SNV30) (continued) Models 3980-3996 Fuel Conversion Kits Conversion Kit, NG to LP - SNV30RN Kit #000-5022 Conversion Kit, LP to NG - SNV30RP Kit #000-5021 Shell Enamel Part Numbers Color T op Left End Right End Front (OP) Left Door Right Door Classic 3000 ...

  • Vermont Casting SNV30 - page 25

    25 Sta r dan ce N atur al V e nt G a s H eater 20007067 Optional Accessories A vailable Fan Kits FK26 Fan The FK26 fan kit helps distribute heated air from within the firebox out into the room. The fan is controlled by a snapstat that turns power on and off as the firebox tem- perature rises above and falls below a preset tempera- ture. A rheosta ...

  • Vermont Casting SNV30 - page 26

    26 26 Sta r dan ce N atur al V e nt G a s H eater 20007067 KT231 Screen in place 6/13/01 djt KT231 Fig. 46 Screen in place. W arming Shelf W arming shelves add versatility to your stove and can be used to keep foods warm at mealtime. Model Color 2702 Classic Black 2684 Biscuit 2685 Chestnut Brown 2688 Vt. Classic Green 2704 Bordeaux 2706 Forest ...

  • Vermont Casting SNV30 - page 27

    27 Sta r dan ce N atur al V e nt G a s H eater 20007067 ...

  • Vermont Casting SNV30 - page 28

    28 28 Sta r dan ce N atur al V e nt G a s H eater 20007067 ...

  • Vermont Casting SNV30 - page 29

    29 Sta r dan ce N atur al V e nt G a s H eater 20007067 ...

  • Vermont Casting SNV30 - page 30

    30 30 Sta r dan ce N atur al V e nt G a s H eater 20007067 BASIC W ARRANTY CFM Corporation (hereinafter referred to collectively as the Company) warrants that your new V ermont Castings or Majestic Gas Fireplace/ Stove is free from manufacturing and material defects for a period of one year from the date of purchase, subject to the following condit ...

  • Vermont Casting SNV30 - page 31

    31 Sta r dan ce N atur al V e nt G a s H eater 20007067 GARANTIE DE BASE La société CFM Corporation (ci-après la « Société ») garantit votre nouveau poêle/foyer au gaz V ermont Castings ou Majestic contre tous défauts de fabrication et de matières premières pour une période d’un an à compter de la date d’achat, sous réserve des co ...

  • Vermont Casting SNV30 - page 32

    Efficiency Ratings Model EnerGuide Ratings Fireplace Efficiency (%) SNV30RN 51.1 SNV30RP 51.1 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 800-668-5323 • www .cfmcorp.com CFM Corporation ...

Fabricant Vermont Casting Catégorie Electric Heater

Les documents que nous recevons du fabricant de l'appareilVermont Casting SNV30 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Vermont Casting
- manuels d’utilisations SNV30
- fiches produit Vermont Casting
- dépliants
- ou étiquettes-énergie Vermont Casting SNV30
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Vermont Casting SNV30.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Vermont Casting SNV30, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Vermont Casting SNV30. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Vermont Casting SNV30.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Vermont Casting SNV30, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Vermont Casting SNV30 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Vermont Casting SNV30.

Le manuel d’utilisation complet Vermont Casting, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Vermont Casting SNV30 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Vermont Casting SNV30, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lVermont Casting SNV30 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Vermont Casting SNV30 - qui devraient nous aider dans les premières étapes lors de l'utilisation Vermont Casting SNV30
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Vermont Casting SNV30
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Vermont Casting SNV30 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Vermont Casting SNV30?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Vermont Casting SNV30, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Vermont Casting SNV30 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)