English dropdown-ico

Manual Vermont Casting SNV30

32 pages 1.6 mb
Download

Go to site of 32

Summary
  • Vermont Casting SNV30 - page 1

    INST ALLER / CONSUMER SAFETY INFORMA TION 20007067 1/07 Rev . 8 PLEASE READ THIS MANUAL BEFORE INST ALLING AND USING APPLIANCE. W ARNING! IF THE INFORMA TION IN THIS MANUAL IS NOT FOLLOWED EXACTL Y , A FIRE OR EXPLOSION MA Y RESUL T CAUSING PROPERTY DAMAGE, PERSONAL INJUR Y OR LOSS OF LIFE. FOR YOUR SAFETY Installation and service must be performed ...

  • Vermont Casting SNV30 - page 2

    2 2 Sta r dan ce N atur al V e nt G a s H eater 20007067 PLEASE READ THE INST ALLA TION & OPERA TING INSTRUCTIONS BEFORE USING APPLIANCE. Thank you and congratulations on your purchase of a V ermont Castings stove. IMPORT ANT : Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may re ...

  • Vermont Casting SNV30 - page 3

    3 Sta r dan ce N atur al V e nt G a s H eater 20007067 The Stardance Natural V ent Room Heater , Model Nos. 3980- 3996 is a vented gas appliance listed to the ANSI standard Z21.88b-2002 and CSA-2.33b-2002 for V ented Room Heaters, and CSA 2.17-M91, Gas-Fired Appliances For Use at High Al - titudes. The installation of the Stardance Natural V ent Ro ...

  • Vermont Casting SNV30 - page 4

    4 4 Sta r dan ce N atur al V e nt G a s H eater 20007067 9" (229mm) C L V alve Inlet 26  " (680 mm) 25" (635 mm) 14  " (355 mm) 3" (76 mm) C L 7067 Stardance fully assembled dimensions 12/22/03 djt V alve Inlet See Page 5 for Flue Collar Centerline Dimensions. 4406 Fig. 1 Stardance dimensions. Stardance Na ...

  • Vermont Casting SNV30 - page 5

    5 Sta r dan ce N atur al V e nt G a s H eater 20007067 Clearance Requirements Minimum Clearances to Combustible Materials Measure side clearances as shown in Figures 2 through 5 from the outer edge of the cast iron stove top. Measure rear clearances from the outermost surface of the sheet metal rear skirt. The Stardance heater is approved for insta ...

  • Vermont Casting SNV30 - page 6

    6 6 Sta r dan ce N atur al V e nt G a s H eater 20007067 V enting Requirements and Options The Stardance must be properly connected to a listed 4” (102 mm) T ype B venting system or to an approved Class A masonry or factory-built chimney system. In Canada, a complete relining of Class A chimney sys- tems is required. The Stardance Natural V ent s ...

  • Vermont Casting SNV30 - page 7

    7 Sta r dan ce N atur al V e nt G a s H eater 20007067 Passing Through a Combustible W all or Ceiling An approved pass-through device is always required when a vent passes through a combustible wall or ceil- ing. Check with the maker of the vent system for the correct listed devices that are available. A listed pass- through device is required whet ...

  • Vermont Casting SNV30 - page 8

    8 8 Sta r dan ce N atur al V e nt G a s H eater 20007067 ST640 RUVSOD snapstat 7/01 Snapstat Bracket Snapstat Module Pinch Grommet to Remove ST670 Fig. 9 Remove the snapstat and grommet from the bracket 4. Connect snapstat leads. Disconnect the snapstat module from the leads inside the snapstat bracket. (Fig. 9) Bend open the snapstat bracket. U ...

  • Vermont Casting SNV30 - page 9

    9 Sta r dan ce N atur al V e nt G a s H eater 20007067 ST194 attach fan to shroud 1 1/99 Outer Shroud Slot Inner Shroud Slot ST194 Fig. 10 Position the fan to engage the inner shroud with the fan bracket slots and secure with sheet metal screws. ST347a JUV FK28  rheostat install 9/21/00 Retaining Nut Control Knob ST347a Fig. 12 Attach r ...

  • Vermont Casting SNV30 - page 10

    10 10 Sta r dan ce N atur al V e nt G a s H eater 20007067 Insert the B-vent adapter into the flue collar and drill 1/8” (3mm) pilot holes through both the stove’s collar and the adapter . Attach the adapter to the flue collar with sheet metal screws. (Fig. 15) Attach the first section of venting to the B-vent adapter . Depending on the leng ...

  • Vermont Casting SNV30 - page 11

    1 1 Sta r dan ce N atur al V e nt G a s H eater 20007067 Burner Information The appliance must only use the gas specified on the rating plate, unless converted using a Fuel Conversion Kit. Refer to Page 25 for the correct Fuel Conversion Kit for your model. Conversion instructions are provided with each kit and beginning on Page 16 in this manual. ...

  • Vermont Casting SNV30 - page 12

    12 12 Sta r dan ce N atur al V e nt G a s H eater 20007067 Install the Front Plate Hold the front plate by the window bars and lift it into position, engaging the two steel tabs on the top corners behind the adjacent bosses in the side plates. (Fig. 21) Then seat the Front against the sides so the tabs at the bottom lip engage with the notches in t ...

  • Vermont Casting SNV30 - page 13

    13 Sta r dan ce N atur al V e nt G a s H eater 20007067 Fig. 22 T o open the front doors, turn handle clockwise. ST261 Stardance operable doors 1/31/01 Clockwise to Open Counterclockwise to Close ST624 The Stardance is operated with the operable door front plate in place with the doors open or closed. T o open the front doors, insert the handle ...

  • Vermont Casting SNV30 - page 14

    14 14 Sta r dan ce N atur al V e nt G a s H eater 20007067 3. Open control access panel. 4. Push in gas control knob slightly and turn clock- wise to “OFF”. Do not force. 5. Close control access panel. 1. STOP! Read the safety information above. 2. Turn of f all electrical power to the fireplace. 3. For MN/MP/TN/TP appliances ONL Y , go on to ...

  • Vermont Casting SNV30 - page 15

    15 Sta r dan ce N atur al V e nt G a s H eater 20007067 A. Defective or misaligned Using a match, light [ilot. If pilot lights, turn off pilot and electrode at the pilot push the ignitor button again. If pilot will not light, check gap at electrode and pilot - it should be 1/8” to have a strong spark. B. Defective ignitor (push Push piezo ignitor ...

  • Vermont Casting SNV30 - page 16

    16 16 Sta r dan ce N atur al V e nt G a s H eater 20007067 Conversion Precautions Conversion must be completed only by qualified personnel. Before proceeding, turn control knob on valve to OFF and turn gas supply OFF . T urn OFF any electricity that may be going to the appliance. CAU- TION: Allow stove to cool completely before beginning conversio ...

  • Vermont Casting SNV30 - page 17

    17 Sta r dan ce N atur al V e nt G a s H eater 20007067 FC107 SIT820 valve conversion 10/03 A B C O F F P I L O T O Fig. 30 Remove mounting screws, pressure regulator tower and spring and diaphragm assembly . FC107 D E F FC108 SIT regulator conversion 10/03 O F F P I L O T O FC108 Fig. 31 Replace regulator . 3. Install the enclosed conversion label ...

  • Vermont Casting SNV30 - page 18

    18 18 Sta r dan ce N atur al V e nt G a s H eater 20007067 17. Replace burner . Slide the burner in at an angle with left side lower than the right side. Slide the left side onto the injectors, making sure the burner leg remains at a 90° angle to the base. Lower the right hand side down in to place. Make sure the burner is as far left as possible ...

  • Vermont Casting SNV30 - page 19

    19 Sta r dan ce N atur al V e nt G a s H eater 20007067 Maintenance Y our Stardance Gas Heater will provide years of service with minimal upkeep. The following procedures will help ensure that your stove continues to function properly . Annual System Inspection Have the entire heater and venting system inspected annually by a qualified gas technic ...

  • Vermont Casting SNV30 - page 20

    20 20 Sta r dan ce N atur al V e nt G a s H eater 20007067 Gasket Replacement The Stardance Gas Heater uses a ‘tadpole’ type gasket to seal between the glass panel and the frame. In time, this gasket can become brittle and compressed and should be replaced. New gasket is available from your dealer . Shut off the gas supply and allow the stove t ...

  • Vermont Casting SNV30 - page 21

    21 Sta r dan ce N atur al V e nt G a s H eater 20007067 NOTE: IF ANY OF THE ORIGINAL WIRE, AS SUP- PLIED WITH THE APPLIANCE, MUST BE RE- PLACED, IT MUST BE REPLACED WITH TYPE SF-2, 200°C WIRE OR ITS EQUIV ALENT . ST665 Fig. 42 Safety Limit Switch wiring.  Ther m ocoupl e Safety Limit Switch Valve ST665 Safety Limit Switch wiring 5/29/01 djt ...

  • Vermont Casting SNV30 - page 22

    22 22 Sta r dan ce N atur al V e nt G a s H eater 20007067 1a 1b 1c PILOT ON OFF PILOT ADJ L O H I 3 5 6 7 20 8a,b 18 4 9a,b 17 19 7067 Stardance NV fully assembled parts 1 1/20/03 djt 23 24 22 a,b,c,d 25 27 21 28 26 30 31 32 2 29 1 1 12 15 10 13 14 16a,b 35 33 34 36 37 38 39 40 42a,b 43 CFM Corporation reserves the right to make changes in design, ...

  • Vermont Casting SNV30 - page 23

    23 Sta r dan ce N atur al V e nt G a s H eater 20007067 Stardance Natural V ent Gas Heater (SNV30) (continued) Models 3980-3996 4. Lava Rock - Burner 57897 5. Gasket, Glass Med. Knit - RDV40 1203702 6. Glass, DV25 1601691 7. Glass Frame Assembly SDV30 30000127 8a. V alve RN Honeywell VS8420E 2038 (Serial #’s up to 6361)* 10001782 8b. V alve RP Ho ...

  • Vermont Casting SNV30 - page 24

    24 24 Sta r dan ce N atur al V e nt G a s H eater 20007067 Stardance Natural V ent Gas Heater (SNV30) (continued) Models 3980-3996 Fuel Conversion Kits Conversion Kit, NG to LP - SNV30RN Kit #000-5022 Conversion Kit, LP to NG - SNV30RP Kit #000-5021 Shell Enamel Part Numbers Color T op Left End Right End Front (OP) Left Door Right Door Classic 3000 ...

  • Vermont Casting SNV30 - page 25

    25 Sta r dan ce N atur al V e nt G a s H eater 20007067 Optional Accessories A vailable Fan Kits FK26 Fan The FK26 fan kit helps distribute heated air from within the firebox out into the room. The fan is controlled by a snapstat that turns power on and off as the firebox tem- perature rises above and falls below a preset tempera- ture. A rheosta ...

  • Vermont Casting SNV30 - page 26

    26 26 Sta r dan ce N atur al V e nt G a s H eater 20007067 KT231 Screen in place 6/13/01 djt KT231 Fig. 46 Screen in place. W arming Shelf W arming shelves add versatility to your stove and can be used to keep foods warm at mealtime. Model Color 2702 Classic Black 2684 Biscuit 2685 Chestnut Brown 2688 Vt. Classic Green 2704 Bordeaux 2706 Forest ...

  • Vermont Casting SNV30 - page 27

    27 Sta r dan ce N atur al V e nt G a s H eater 20007067 ...

  • Vermont Casting SNV30 - page 28

    28 28 Sta r dan ce N atur al V e nt G a s H eater 20007067 ...

  • Vermont Casting SNV30 - page 29

    29 Sta r dan ce N atur al V e nt G a s H eater 20007067 ...

  • Vermont Casting SNV30 - page 30

    30 30 Sta r dan ce N atur al V e nt G a s H eater 20007067 BASIC W ARRANTY CFM Corporation (hereinafter referred to collectively as the Company) warrants that your new V ermont Castings or Majestic Gas Fireplace/ Stove is free from manufacturing and material defects for a period of one year from the date of purchase, subject to the following condit ...

  • Vermont Casting SNV30 - page 31

    31 Sta r dan ce N atur al V e nt G a s H eater 20007067 GARANTIE DE BASE La société CFM Corporation (ci-après la « Société ») garantit votre nouveau poêle/foyer au gaz V ermont Castings ou Majestic contre tous défauts de fabrication et de matières premières pour une période d’un an à compter de la date d’achat, sous réserve des co ...

  • Vermont Casting SNV30 - page 32

    Efficiency Ratings Model EnerGuide Ratings Fireplace Efficiency (%) SNV30RN 51.1 SNV30RP 51.1 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 800-668-5323 • www .cfmcorp.com CFM Corporation ...

Manufacturer Vermont Casting Category Electric Heater

Documents that we receive from a manufacturer of a Vermont Casting SNV30 can be divided into several groups. They are, among others:
- Vermont Casting technical drawings
- SNV30 manuals
- Vermont Casting product data sheets
- information booklets
- or energy labels Vermont Casting SNV30
All of them are important, but the most important information from the point of view of use of the device are in the user manual Vermont Casting SNV30.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Vermont Casting SNV30, service manual, brief instructions and user manuals Vermont Casting SNV30. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Vermont Casting SNV30.

Similar manuals

A complete manual for the device Vermont Casting SNV30, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Vermont Casting SNV30 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Vermont Casting SNV30.

A complete Vermont Casting manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Vermont Casting SNV30 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Vermont Casting SNV30, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Vermont Casting SNV30, that we can find in the current document
3. Tips how to use the basic functions of the device Vermont Casting SNV30 - which should help us in our first steps of using Vermont Casting SNV30
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Vermont Casting SNV30
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Vermont Casting SNV30 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Vermont Casting SNV30?

Use the form below

If you did not solve your problem by using a manual Vermont Casting SNV30, ask a question using the form below. If a user had a similar problem with Vermont Casting SNV30 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)