Manuel d’utilisation Audiovox AS-9055

16 pages 0.38 mb
Télécharger

Aller à la page of 16

Summary
  • Audiovox AS-9055 - page 1

    128-6832 1 of 16 Kit Contents (1) - Control Module (2) - 1 Button High Frequency Transmitters (1) - 1 Channel Code Learning Receiver (1) - Multi Pin Input/Output Harness (1) - Six Pin Power Harness (1) - Four Pin Accessory Output (Pulse Before & After Start, During Crank & After Shut Down) (2) - 30 Amp In-line Fuse Holders With Fuses (1) - ...

  • Audiovox AS-9055 - page 2

    128-6832 2 of 16 This Remote Start System is designed for use with Automatic T ransmission Vehicles Only! The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the RF signal is r ...

  • Audiovox AS-9055 - page 3

    128-6832 3 of 16 3 THE RECEIVER/ANTENNA ASSEMBL Y : The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dashboard for maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception. Special considerations must be made for windshield glass as some newer veh ...

  • Audiovox AS-9055 - page 4

    128-6832 4 of 16 NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutral switch configuration, this connection must be made between the starter inhibit relay , (when used) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition switc ...

  • Audiovox AS-9055 - page 5

    128-6832 5 of 16 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to the "OFF" and "ST ART" or ...

  • Audiovox AS-9055 - page 6

    128-6832 6 of 16 BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2 Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even if the signal is received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to the brake light circuit, connect the Brown w/ Black trace ...

  • Audiovox AS-9055 - page 7

    128-6832 7 of 16 LIGHT BLUE Wire: Ignition 3 / Shock Disable Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of the applications described below , a relay will be requi ...

  • Audiovox AS-9055 - page 8

    128-6832 8 of 16 DARK GREEN Wire: T ach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil. This Remote Start uni ...

  • Audiovox AS-9055 - page 9

    128-6832 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Blue Connector : Programming Switch Route the gray and black wires in the 2 pin connector from the previously installed programming switch to the control module and plug it into the mating blue ...

  • Audiovox AS-9055 - page 10

    128-6832 10 of 16 10 X Pause,etc... X Pause,etc... 3. Diagnostics: 1. Be sure that programmable feature number #6 is set to the "Diagnostics On" mode. 2. Press and hold the program switch on, then turn the ignition key to the "ON" position. 3. The lights will flash and the number of flashes will indicate the reason for shutdown ...

  • Audiovox AS-9055 - page 11

    128-6832 11 of 16 11 W ARNING!! DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERA TION OF THE HOOD PIN SAFETY SHUT DOWN FEA TURE. MANUAL SHUT DOWN / ENABLE CIRCUIT : The intent of the manual shut down / enable circuit is to allow the vehicle operator to prevent operation of the Remote Start Unit regardless of the RF transmitte ...

  • Audiovox AS-9055 - page 12

    128-6832 12 of 16 configuration prevents mechanical operation while the vehicle is in gear but offers no consideration for electrical operation. Because of this potential problem, this installation requires the additional connection of a safety wire from the remote start device to the vehicle Park/Neutral ECM Input or the vehicle key in sensor . Th ...

  • Audiovox AS-9055 - page 13

    128-6832 13 of 16 METHOD 1 T o connect to the key in sensor as shown in method 1: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder ...

  • Audiovox AS-9055 - page 14

    128-6832 14 of 16 14 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be connected to ...

  • Audiovox AS-9055 - page 15

    128-6832 15 of 16 15 ...

  • Audiovox AS-9055 - page 16

    128-6832 16 of 16 © 2003 Audiovox Electronics Corp., Hauppauge, NY 1 1788 1286832 ...

Fabricant Audiovox Catégorie Remote Starter

Les documents que nous recevons du fabricant de l'appareilAudiovox AS-9055 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Audiovox
- manuels d’utilisations AS-9055
- fiches produit Audiovox
- dépliants
- ou étiquettes-énergie Audiovox AS-9055
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Audiovox AS-9055.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Audiovox AS-9055, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Audiovox AS-9055. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Audiovox AS-9055.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Audiovox AS-9055, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Audiovox AS-9055 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Audiovox AS-9055.

Le manuel d’utilisation complet Audiovox, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Audiovox AS-9055 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Audiovox AS-9055, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAudiovox AS-9055 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Audiovox AS-9055 - qui devraient nous aider dans les premières étapes lors de l'utilisation Audiovox AS-9055
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Audiovox AS-9055
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Audiovox AS-9055 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Audiovox AS-9055?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Audiovox AS-9055, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Audiovox AS-9055 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)