Français dropdown-ico

Manuel d’utilisation Outback Power Systems FW-SP-R

22 pages 0.57 mb
Télécharger

Aller à la page of 22

Summary
  • Outback Power Systems FW-SP-R - page 1

    Sur ge P r ot ec tor FW -SP-A CA FW -SP-250 FW -SP-R U ser ’ s Guide Includes M ounting and Installation ...

  • Outback Power Systems FW-SP-R - page 2

    About OutBack P ower S ystems OutBack P ower Systems is a leader in advanced ener gy conversion t echnology . Our products include true sine wave in verter/chargers, maximum power point char ge controllers, syst em com- munication components, as well as br eaker panels, breakers, accessories, and assembled syst ems. Notice of Cop yright FLEXware Su ...

  • Outback Power Systems FW-SP-R - page 3

    2 W arranty I ntroduction Dear OutBack Customer , Thank you for y our purchase of OutBack products. We make every e or t to assur e our power con- version products will give y ou long and reliable ser vice for your r enewable energy system. As with any manufactured device , repairs might be needed due to damage , inappropriate use, or unintentio ...

  • Outback Power Systems FW-SP-R - page 4

    OUTBACK FLEX ware Surge P rotector INST ALLA TION GUIDELINES AND SAFET Y INSTRUC TIONS This product is intended to be installed as part of a permanently grounded electrical system . • The FLEXware Sur ge P rotector is designed f or indoor installation or installation inside a weatherproof enclosure . • F or full system protection, one FLEXware ...

  • Outback Power Systems FW-SP-R - page 5

    INTRODUC TION The OutBack FLEXware Sur ge Pr otec tor connects to the f ollowing FX Ser ies Inverter/Charger por ts: • DC+ • DC- • AC HO T IN • AC NEUTRAL IN • AC HO T OUT • AC NEUTRAL OUT • GROUND The FLEXware Sur ge Pr otec tor is desig ned to protect the FX’ s sensitive components from excessively high v oltages (e.g., electrical ...

  • Outback Power Systems FW-SP-R - page 6

    The FLEX ware Surge P rotector Speci cations LEDs • AC TIVE lights are y ellow (power is present). • ERROR lights are red (pr otection in that circuit is compromised , replacing the surge pr otec tor is recommended). • F or the ERR OR light to show , its circuit must be pow ered; its ACTIVE light will also glow. Figur e 3 : Surge P rotecto ...

  • Outback Power Systems FW-SP-R - page 7

    FW-SP -ACA The FW-SP -ACA consists of an FW-A CA with an included surge prot ector and is installed onto an FX Series Inver ter/Char ger . Figur e 4: FLEXware Sur ge Pr otec tor -ACA LEDs Underside screw secures FW-SP -ACA to FX Phillips screw secur es FW-SP -ACA bracket and surge prot ector board to the FW-SP -ACA Underside screw secures FW-SP -AC ...

  • Outback Power Systems FW-SP-R - page 8

    (1) Remove the DC C or T urbo (secured by four Phillips corner screws) (2) Remove the DC battery caps (under the DCC or T urbo) (3) Remove the AC Wiring Compartment plastic cover (secured with two Phillips screws) (5) Remove the AC C on- duit Plate, which slides up and out from the FX (4) Remove these two M5 hex bolts from the FX Figur e 5 : Removi ...

  • Outback Power Systems FW-SP-R - page 9

    (7) Remove the appropriate knockouts for the individual power application. Note that knockouts should be scored  rst with a utility knife and then removed . The dual, concentric knock out on the back o ers openings for the FW500, FW1000, PS2 and PS4 AC enclosures . (9) The FW-SP-ACA slides ont o the FX in the same location as the now remov ed ...

  • Outback Power Systems FW-SP-R - page 10

    9 (11) Inser t a bushing into the AC enclosur e (it is not critical that this bushing line up precisely with the FW-SP -ACA); if  exible cable is used instead of an enclosure , appropriate strain relief is r equired. Screws (included) secure the FW -SP-A CA to an FX FW-SP -ACA slides down FX slots Figur e 7: T op view of FW-SP-ACA installed on a ...

  • Outback Power Systems FW-SP-R - page 11

    FW-SP -250 The FW-SP -250 is a two-piece combined FLEXware 250 top cover and FLEX ware Surge P rotector . I t replaces an existing FLEXwar e 250 cover , attaching at the AC end of the FLEXware 250. Pr ocedure The FLEXware 250 A C should already be installed (see FW250 AC instructions) and all AC and DC power shut o . (4) Replace the standard FLE ...

  • Outback Power Systems FW-SP-R - page 12

    (8) Route the FW-SP -250 wires through to the A C Wiring Compartment and to the batter y lugs. (9) Secure the surge pr otec tor’ s wiring in the appropriate locations and replace the various plastic covers as per the wiring instructions on page 16. 11 (5) Install the top section of the cover contain- ing the surge prot ector  rst. (6) The lowe ...

  • Outback Power Systems FW-SP-R - page 13

    Figur e 11: FW-ACA (2) Remove the FW-A CA plastic cover (secured with two Phillips screws) (3) Remove the FW- ACA Bracket (secured with one Phillips screw); if a damaged FLEXware Sur ge Pr otec tor is being replaced, r emove it by disengaging the locating pin FW-ACA housing Locating pin FW-SP -R (REPLACEMENT ) for the FW -SP-A CA or the FW-A CA An ...

  • Outback Power Systems FW-SP-R - page 14

    1/ 3/07 The locating pin on the FW-ACA bracket  ts in this slot (4) P ass the FW-SP -R wires through the FW - ACA Bracket opening, lining up the locating pin with the slot on the surge prot ector . FW-SP -R LEDs Figur es 12: FW-SP -R and FW-ACA Bracket 13 ...

  • Outback Power Systems FW-SP-R - page 15

    (5) With the FW-SP-R attached t o the FW-ACA Bracket, hold the ends of the FW-SP -R wires and slide it and the bracket back inside the FW-ACA to its original location. NO TE: The FW-SP -R slides into a double slot at the bottom of the FW-ACA. The LEDs should be level with the top of the FW-A CA housing. Figur e 13: FW-SP -R installed inside the FW- ...

  • Outback Power Systems FW-SP-R - page 16

    (6) When the new surge protector board has been secured to the FW-SP -250 cover , reinstall the FW-SP -250 as shown on pages 10-11. (3) Remove the FW-SP -250 (secured by six Phillips screws). (2) Remove the AC Wiring Compartment cover (secured by two Phillips screws). (1) Remove the DC C or T urbo cover (secured by f our Phillips screws) and the DC ...

  • Outback Power Systems FW-SP-R - page 17

    Wiring and C onnec ting the FLEX ware Surge Pr otec tor With the FW-SP -250 or FW-SP-ACA secur ed, connect all AC and DC wiring as well as any HUB, MA TE, A UX, and BA T TERY TEMP cables. • Install all AC and DC power cables  rst followed by the sur ge protector wires in their appropriate locations; each wire is labeled on the shrink- wrapped ...

  • Outback Power Systems FW-SP-R - page 18

    • Install the various covers in this order with the DCC or Turbo last: (1) DC battery terminals (2) FW-ACA (if used) (3) AC Wiring Compar tment Figur e 16: After wiring, install all covers . The surge prot ector ’ s DC + and DC- cables and the BA T T TEMP sensor cable pass under this rubber bushing The system can now be po wered up • DC power ...

  • Outback Power Systems FW-SP-R - page 19

    18 FLEX ware ™ Surge P rotector Limited W arranty OutBack P ower Systems , Inc. (“OutBack ”) provides a limit ed warranty (“ Warranty ”) against defects in materials and workmanship for its FLEXware Sur ge Pr otec tor P roducts (“Product”) if installed for use with OutBack FX Series Inverter/Chargers in  xed location applications. ...

  • Outback Power Systems FW-SP-R - page 20

    19 1. P roof- of-purchase in the f or m of a copy of the original P roduct purchase invoice or r eceipt con rming the Pr oduct model number and serial number ; 2. OutBack issued warranty cer ti cate f or the FX Series I n verter/Charger used with the Pr oduc t; 3. Description of the problem; and 4. Shipping address f or the replacement equipm ...

  • Outback Power Systems FW-SP-R - page 21

    Surge P rotector Limited W arranty Registra tion 20 Revision 2007-06-20 Surge P rotector Limited W arrant y Registration Complete this form to request a Limited W arranty , and return it to: Outback P ower Systems Inc. 19009 62nd Ave . NE Arlington, W A 98223 Note: A Limited Warranty Cer ti cate will only be issued if this Registration Card is r ...

  • Outback Power Systems FW-SP-R - page 22

    900-0089-01-00 REV A European Sales O c e Barcelona, España (+34) 600-843-845 19009 62nd Avenue NE Arlington, W A USA (+1) 360-435-6030 www.outbackpower .com ...

Fabricant Outback Power Systems Catégorie Surge Protector

Les documents que nous recevons du fabricant de l'appareilOutback Power Systems FW-SP-R peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Outback Power Systems
- manuels d’utilisations FW-SP-R
- fiches produit Outback Power Systems
- dépliants
- ou étiquettes-énergie Outback Power Systems FW-SP-R
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Outback Power Systems FW-SP-R.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Outback Power Systems FW-SP-R, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Outback Power Systems FW-SP-R. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Outback Power Systems FW-SP-R.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Outback Power Systems FW-SP-R, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Outback Power Systems FW-SP-R par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Outback Power Systems FW-SP-R.

Le manuel d’utilisation complet Outback Power Systems, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Outback Power Systems FW-SP-R - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Outback Power Systems FW-SP-R, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lOutback Power Systems FW-SP-R qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Outback Power Systems FW-SP-R - qui devraient nous aider dans les premières étapes lors de l'utilisation Outback Power Systems FW-SP-R
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Outback Power Systems FW-SP-R
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Outback Power Systems FW-SP-R dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Outback Power Systems FW-SP-R?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Outback Power Systems FW-SP-R, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Outback Power Systems FW-SP-R il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)