English dropdown-ico

Manual Outback Power Systems FW-SP-R

22 pages 0.57 mb
Download

Go to site of 22

Summary
  • Outback Power Systems FW-SP-R - page 1

    Sur ge P r ot ec tor FW -SP-A CA FW -SP-250 FW -SP-R U ser ’ s Guide Includes M ounting and Installation ...

  • Outback Power Systems FW-SP-R - page 2

    About OutBack P ower S ystems OutBack P ower Systems is a leader in advanced ener gy conversion t echnology . Our products include true sine wave in verter/chargers, maximum power point char ge controllers, syst em com- munication components, as well as br eaker panels, breakers, accessories, and assembled syst ems. Notice of Cop yright FLEXware Su ...

  • Outback Power Systems FW-SP-R - page 3

    2 W arranty I ntroduction Dear OutBack Customer , Thank you for y our purchase of OutBack products. We make every e or t to assur e our power con- version products will give y ou long and reliable ser vice for your r enewable energy system. As with any manufactured device , repairs might be needed due to damage , inappropriate use, or unintentio ...

  • Outback Power Systems FW-SP-R - page 4

    OUTBACK FLEX ware Surge P rotector INST ALLA TION GUIDELINES AND SAFET Y INSTRUC TIONS This product is intended to be installed as part of a permanently grounded electrical system . • The FLEXware Sur ge P rotector is designed f or indoor installation or installation inside a weatherproof enclosure . • F or full system protection, one FLEXware ...

  • Outback Power Systems FW-SP-R - page 5

    INTRODUC TION The OutBack FLEXware Sur ge Pr otec tor connects to the f ollowing FX Ser ies Inverter/Charger por ts: • DC+ • DC- • AC HO T IN • AC NEUTRAL IN • AC HO T OUT • AC NEUTRAL OUT • GROUND The FLEXware Sur ge Pr otec tor is desig ned to protect the FX’ s sensitive components from excessively high v oltages (e.g., electrical ...

  • Outback Power Systems FW-SP-R - page 6

    The FLEX ware Surge P rotector Speci cations LEDs • AC TIVE lights are y ellow (power is present). • ERROR lights are red (pr otection in that circuit is compromised , replacing the surge pr otec tor is recommended). • F or the ERR OR light to show , its circuit must be pow ered; its ACTIVE light will also glow. Figur e 3 : Surge P rotecto ...

  • Outback Power Systems FW-SP-R - page 7

    FW-SP -ACA The FW-SP -ACA consists of an FW-A CA with an included surge prot ector and is installed onto an FX Series Inver ter/Char ger . Figur e 4: FLEXware Sur ge Pr otec tor -ACA LEDs Underside screw secures FW-SP -ACA to FX Phillips screw secur es FW-SP -ACA bracket and surge prot ector board to the FW-SP -ACA Underside screw secures FW-SP -AC ...

  • Outback Power Systems FW-SP-R - page 8

    (1) Remove the DC C or T urbo (secured by four Phillips corner screws) (2) Remove the DC battery caps (under the DCC or T urbo) (3) Remove the AC Wiring Compartment plastic cover (secured with two Phillips screws) (5) Remove the AC C on- duit Plate, which slides up and out from the FX (4) Remove these two M5 hex bolts from the FX Figur e 5 : Removi ...

  • Outback Power Systems FW-SP-R - page 9

    (7) Remove the appropriate knockouts for the individual power application. Note that knockouts should be scored  rst with a utility knife and then removed . The dual, concentric knock out on the back o ers openings for the FW500, FW1000, PS2 and PS4 AC enclosures . (9) The FW-SP-ACA slides ont o the FX in the same location as the now remov ed ...

  • Outback Power Systems FW-SP-R - page 10

    9 (11) Inser t a bushing into the AC enclosur e (it is not critical that this bushing line up precisely with the FW-SP -ACA); if  exible cable is used instead of an enclosure , appropriate strain relief is r equired. Screws (included) secure the FW -SP-A CA to an FX FW-SP -ACA slides down FX slots Figur e 7: T op view of FW-SP-ACA installed on a ...

  • Outback Power Systems FW-SP-R - page 11

    FW-SP -250 The FW-SP -250 is a two-piece combined FLEXware 250 top cover and FLEX ware Surge P rotector . I t replaces an existing FLEXwar e 250 cover , attaching at the AC end of the FLEXware 250. Pr ocedure The FLEXware 250 A C should already be installed (see FW250 AC instructions) and all AC and DC power shut o . (4) Replace the standard FLE ...

  • Outback Power Systems FW-SP-R - page 12

    (8) Route the FW-SP -250 wires through to the A C Wiring Compartment and to the batter y lugs. (9) Secure the surge pr otec tor’ s wiring in the appropriate locations and replace the various plastic covers as per the wiring instructions on page 16. 11 (5) Install the top section of the cover contain- ing the surge prot ector  rst. (6) The lowe ...

  • Outback Power Systems FW-SP-R - page 13

    Figur e 11: FW-ACA (2) Remove the FW-A CA plastic cover (secured with two Phillips screws) (3) Remove the FW- ACA Bracket (secured with one Phillips screw); if a damaged FLEXware Sur ge Pr otec tor is being replaced, r emove it by disengaging the locating pin FW-ACA housing Locating pin FW-SP -R (REPLACEMENT ) for the FW -SP-A CA or the FW-A CA An ...

  • Outback Power Systems FW-SP-R - page 14

    1/ 3/07 The locating pin on the FW-ACA bracket  ts in this slot (4) P ass the FW-SP -R wires through the FW - ACA Bracket opening, lining up the locating pin with the slot on the surge prot ector . FW-SP -R LEDs Figur es 12: FW-SP -R and FW-ACA Bracket 13 ...

  • Outback Power Systems FW-SP-R - page 15

    (5) With the FW-SP-R attached t o the FW-ACA Bracket, hold the ends of the FW-SP -R wires and slide it and the bracket back inside the FW-ACA to its original location. NO TE: The FW-SP -R slides into a double slot at the bottom of the FW-ACA. The LEDs should be level with the top of the FW-A CA housing. Figur e 13: FW-SP -R installed inside the FW- ...

  • Outback Power Systems FW-SP-R - page 16

    (6) When the new surge protector board has been secured to the FW-SP -250 cover , reinstall the FW-SP -250 as shown on pages 10-11. (3) Remove the FW-SP -250 (secured by six Phillips screws). (2) Remove the AC Wiring Compartment cover (secured by two Phillips screws). (1) Remove the DC C or T urbo cover (secured by f our Phillips screws) and the DC ...

  • Outback Power Systems FW-SP-R - page 17

    Wiring and C onnec ting the FLEX ware Surge Pr otec tor With the FW-SP -250 or FW-SP-ACA secur ed, connect all AC and DC wiring as well as any HUB, MA TE, A UX, and BA T TERY TEMP cables. • Install all AC and DC power cables  rst followed by the sur ge protector wires in their appropriate locations; each wire is labeled on the shrink- wrapped ...

  • Outback Power Systems FW-SP-R - page 18

    • Install the various covers in this order with the DCC or Turbo last: (1) DC battery terminals (2) FW-ACA (if used) (3) AC Wiring Compar tment Figur e 16: After wiring, install all covers . The surge prot ector ’ s DC + and DC- cables and the BA T T TEMP sensor cable pass under this rubber bushing The system can now be po wered up • DC power ...

  • Outback Power Systems FW-SP-R - page 19

    18 FLEX ware ™ Surge P rotector Limited W arranty OutBack P ower Systems , Inc. (“OutBack ”) provides a limit ed warranty (“ Warranty ”) against defects in materials and workmanship for its FLEXware Sur ge Pr otec tor P roducts (“Product”) if installed for use with OutBack FX Series Inverter/Chargers in  xed location applications. ...

  • Outback Power Systems FW-SP-R - page 20

    19 1. P roof- of-purchase in the f or m of a copy of the original P roduct purchase invoice or r eceipt con rming the Pr oduct model number and serial number ; 2. OutBack issued warranty cer ti cate f or the FX Series I n verter/Charger used with the Pr oduc t; 3. Description of the problem; and 4. Shipping address f or the replacement equipm ...

  • Outback Power Systems FW-SP-R - page 21

    Surge P rotector Limited W arranty Registra tion 20 Revision 2007-06-20 Surge P rotector Limited W arrant y Registration Complete this form to request a Limited W arranty , and return it to: Outback P ower Systems Inc. 19009 62nd Ave . NE Arlington, W A 98223 Note: A Limited Warranty Cer ti cate will only be issued if this Registration Card is r ...

  • Outback Power Systems FW-SP-R - page 22

    900-0089-01-00 REV A European Sales O c e Barcelona, España (+34) 600-843-845 19009 62nd Avenue NE Arlington, W A USA (+1) 360-435-6030 www.outbackpower .com ...

Manufacturer Outback Power Systems Category Surge Protector

Documents that we receive from a manufacturer of a Outback Power Systems FW-SP-R can be divided into several groups. They are, among others:
- Outback Power Systems technical drawings
- FW-SP-R manuals
- Outback Power Systems product data sheets
- information booklets
- or energy labels Outback Power Systems FW-SP-R
All of them are important, but the most important information from the point of view of use of the device are in the user manual Outback Power Systems FW-SP-R.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Outback Power Systems FW-SP-R, service manual, brief instructions and user manuals Outback Power Systems FW-SP-R. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Outback Power Systems FW-SP-R.

Similar manuals

A complete manual for the device Outback Power Systems FW-SP-R, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Outback Power Systems FW-SP-R by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Outback Power Systems FW-SP-R.

A complete Outback Power Systems manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Outback Power Systems FW-SP-R - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Outback Power Systems FW-SP-R, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Outback Power Systems FW-SP-R, that we can find in the current document
3. Tips how to use the basic functions of the device Outback Power Systems FW-SP-R - which should help us in our first steps of using Outback Power Systems FW-SP-R
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Outback Power Systems FW-SP-R
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Outback Power Systems FW-SP-R in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Outback Power Systems FW-SP-R?

Use the form below

If you did not solve your problem by using a manual Outback Power Systems FW-SP-R, ask a question using the form below. If a user had a similar problem with Outback Power Systems FW-SP-R it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)