Manuel d’utilisation Delta 36-312

17 pages 0.74 mb
Télécharger

Aller à la page of 17

Summary
  • Delta 36-312 - page 1

    INSTRUCTION MANUAL ESP AÑOL: PÁGINA 17 T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 12" Single-Bevel Compound Miter Saw (Model 36-312) Patents Pending P ART NO. 910706 - 10-10-03 Copyright ...

  • Delta 36-312 - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta 36-312 - page 3

    3 GENERAL SAFETY RULES 1. FOR YOUR OWN SAFETY , READ THE INSTRUC- TION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly mini- mize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT . Eye protection equipment should comply with ANSI Z87.1 standards, ...

  • Delta 36-312 - page 4

    4 ADDITIONAL SAFETY RULES FOR MITER SA WS Refer to them often and use them to instruct others . F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS INJURY . 04-24-03 SA VE THESE INSTRUCTIONS . 1. DO NOT OPERA TE THIS MACHINE until it is completely assembled and installed according to the instructions. A machine incorrectly assembled can cause se ...

  • Delta 36-312 - page 5

    5 Y our new Compound Miter Saw is DOUBLE-INSULA TED to give you added safety . As a result, this saw is equipped with a two-prong plug which permits you to use any conventional 120 volt electrical outlet with concern for maintaining a ground connection. Before connecting the motor to the power sour ce, confirm that the electric current is 120 volts ...

  • Delta 36-312 - page 6

    6 B Fig. 3A A ASSEMBL Y AND OPERA TION Fig. 3 C DA B Fig. 4 A TT ACHING DUST BAG 1. Attach dust spout (A) Fig. 3 to port (B). 2. Depress spring clips (C) Fig. 3 of dust bag (D) and clip dust bag (D) over rib of dust spout (A). MOVING CUTTINGHEAD TO THE UP POSITION Push down on the handle (B) Fig. 3A, pull out cutting- head lockpin and move the cutt ...

  • Delta 36-312 - page 7

    7 Fig. 5 A B C E D E Fig.6 FENCE OPERA TION The saw is supplied with left fence segment (A) Fig. 7 that incorporates a squeeze clamp feature. T o operate the fence segment or to slide to another location, squeeze the clamp (A) Fig. 7 to disengage the lock. Slide the fence to desired location and r elease to lock the fence. T o remove the fence, dep ...

  • Delta 36-312 - page 8

    8 A B C D E B 1. The compound miter saw will cut any angle from a straight 0° cut to 48° right and left. T urn the locking knob (A) Fig. 13 counterclockwise, depr ess the lock lever (B), and rotate the table to the desired position. 2. This machine is equipped with positive stops at the 0° cut-off position and at the 15°, 22.5°, 31.6°, and 45 ...

  • Delta 36-312 - page 9

    9 Fig. 16 C A D B DISCONNECT THE MACHINE FROM THE POWER SOURCE. Fig. 15 T o adjust the sliding fit between the movable table and the base, turn the nut (A) Fig. 15 clockwise to tighten the fit (counter -clockwise to loosen the fit). This adjustment should not be so tight that it restricts the r otating movement of the table, or so loose that it aff ...

  • Delta 36-312 - page 10

    DISCONNECT THE MACHINE FROM THE POWER SOURCE. 1. Position the bevel detent plate so that the desired angle (A) Fig. 23 is exposed immediately to the left of the housing (H) Fig. 23. 2. Lift the front handle (A) Fig. 22 to disengage bevel lock. 3. Tilt the cuttinghead left as desired until it stops on plate (A) Fig. 23. NOTE: Fig. 25 illustrates the ...

  • Delta 36-312 - page 11

    11 DISCONNECT THE MACHINE FROM THE POWER SOURCE. 1. Position the bevel detent plate so that the desired angle (A) Fig. 25 is exposed. 2. Lift the front handle (A) Fig. 26 to disengage the bevel lock. 3. Tilt the cuttinghead left until it stops on the plate (B) Fig. 25. 4. T o adjust, loosen the pin locking set screw (C) Fig. 27 (shown fr om the rea ...

  • Delta 36-312 - page 12

    If the size of the workpiece causes your hand to be inside the table hazard zone (see section “T ABLE HAZARD ZONE” SEE FIG. 21 ), use a clamp to secure the workpiece. AUXILIAR Y WOOD FENCE When performing multiple or repetitive cut-of f operations that result in small cut-of f pieces (one inch or less), the saw blade can catch the cut-off piece ...

  • Delta 36-312 - page 13

    13 Fig. 36 CORRECT CUTTING BOWED MA TERIAL 1. Check the workpiece. If it is bowed, position the workpiece on the table as shown in Fig. 36. 2. When the workpiece is positioned the wrong way (Fig. 37), it will pinch the blade near the completion of the cut. Fig. 37 INCORRECT CUTTING CROWN MOULDING CUTTING CROWN MOULDING One of the many features of t ...

  • Delta 36-312 - page 14

    14 Fig. 42 A MAINTENANCE Disconnect the machine from the power sour ce. Fig. 43 E G C D H Fig. 44 F CHANGING THE BLADE J 1. Use only 12" diameter blades (with 1" arbor holes) that are rated for 5000 RPM or higher . 2. Use the supplied wrench to loosen scr ews (A) Fig. 42. NOTE: One screw is located under the arbor cover arm. 3. Rotate the ...

  • Delta 36-312 - page 15

    15 Fig.46 B C Fig. 45 A A BRUSH INSPECTION AND REPLACEMENT Before inspecting brushes, disconnect the machine fr om the power source. Brush life varies, depending on the load on the motor . Check the brushes after the first 50 hours, or after a new set of brushes has been installed. After the first check, examine them about every 10 hours. The brush ...

  • Delta 36-312 - page 16

    16 T wo Y ear Limited New Pr oduct W arranty Delta will repair or r eplace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, pr ovided that the customer returns the product prepaid to a Delta factory service center or authorized ser ...

  • Delta 36-312 - page 17

    The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ACRAFT ® , DEL T AGRAM™, Delta Series 2000™, DURA TRONIC™, Emc²™, FLEX ® , Flying Chips? ...

Fabricant Delta Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilDelta 36-312 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Delta
- manuels d’utilisations 36-312
- fiches produit Delta
- dépliants
- ou étiquettes-énergie Delta 36-312
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Delta 36-312.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Delta 36-312, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Delta 36-312. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Delta 36-312.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Delta 36-312, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Delta 36-312 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Delta 36-312.

Le manuel d’utilisation complet Delta, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Delta 36-312 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Delta 36-312, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDelta 36-312 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Delta 36-312 - qui devraient nous aider dans les premières étapes lors de l'utilisation Delta 36-312
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Delta 36-312
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Delta 36-312 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Delta 36-312?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Delta 36-312, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Delta 36-312 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)