Français dropdown-ico

Manuel d’utilisation Telex FMR-10

26 pages 0.54 mb
Télécharger

Aller à la page of 26

Summary
  • Telex FMR-10 - page 1

    Telex â Operating Instructions FMR-10 SERIES WIRELESS USER GUIDE Channel Diversity Audio RF A B 1 234 -20 -10 0 +3 T elex R CLEAR SCAN TM FMR-10 T e l e x P O W E R B A T . N O A U D I O T e l e x W T - 1 0 U H F T R A N S M I T T E R R ...

  • Telex FMR-10 - page 2

    ...

  • Telex FMR-10 - page 3

    T able of Contents Section Page 1. Quick System Setup Guide . . . . . . . . . . . . . . . . . . . . . . . 1 2. System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Detailed system/component setup instructions . . . . . . . . 4 3.1. FMR-10 Receiver Setup and Operation . . . . . . . . . . 4 3.1.1 Rack Mount Installation . ...

  • Telex FMR-10 - page 4

    T ransmitter Setup T ransmitter Setup 1. Open battery compartment, install 9 Volt battery. Make sure to observe proper battery polarity. 2. Adjust channel setting to match channel number shown on re - ceiver channel display. Replace battery cover. 3. If using bodypack transmitter, plug the microphone into the trans - mitter connector. Operating the ...

  • Telex FMR-10 - page 5

    2. System Description The Telex FMR-10 Wireless is a series of 10 channel frequency agile UHF wireless systems that combine Telex’s legendary quality and reliability with high value. The transmitters and receivers operate in the UHF frequency range. The well-designed audio circuitry ensures excellent signal-to-noise ratio with accurate sound qual ...

  • Telex FMR-10 - page 6

    3. Detailed Setup Instructions 3.1 FMR-10 Receiver Setup & Operation Receiver Setup & Operation 1. Place the receiver where there is a clear line of sight to the area where the transmitter will be used. 2. Attach either the supplied 1/4-wave antennas or two remotely mounted antennas to the antenna connectors on the rear panel of the FMR-10. ...

  • Telex FMR-10 - page 7

    CAUTION: Please make sure that the AC adapter is the cor - rect voltage for your local requirements. 4. ClearScan ™ : The FMR-10 Wireless system features ClearScan ™ . ClearScan ™ automates the process of finding a clear channel to use in setup of your FMR-10 Wireless system. To use ClearScan ™ , depress and hold down the set button for 3 s ...

  • Telex FMR-10 - page 8

    NOTE: If the system is in “lock-out”, ClearScan ™ will not fun ction. 7. Make sure the gain setting is muted or turned down on the mixer or amp channel you will connect the wireless system to. 8. Plug the audio cable (not supplied) into the output connector. NOTE: The 3-pin XLR-type connector output level is fixed, and cannot be adjusted. Now ...

  • Telex FMR-10 - page 9

    3.1.1 Rack Mount Installation 3.1.1 Rack Mount Installation The FMR-10 is supplied with rack mounts for single and double mount - ing in a standard EIA 19”/ 483mm equipment rack (see Figure 3). For rack mounting a single unit, a long and short “ear” are used. For dual side-by-side mounting, use the short “ears” and the mid sized brackets ...

  • Telex FMR-10 - page 10

    2. Install the previously removed screws. Insert an additional screw (provided in the parts pack) into the remaining holes. Tighten all screws securely. 3. Place the two assemblies side-by-side with the mid brackets to - gether. (The left bracket should fit above the right so that the countersinks are visible). Install 4 flat-head screws (Item #5) ...

  • Telex FMR-10 - page 11

    3.1.2 Antenna Placement 3.1.2 Antenna Placement For any wireless system to perform correctly, strong RF signals are mandatory. To maximize signal strength, good antenna placement must be utilized. Although some situations prohibit perfect antenna placement, here are some guidelines: 1. The antennas should be placed in a location with a clear signal ...

  • Telex FMR-10 - page 12

    If antennas are remote-mounted, separating them 6 feet (1.8m) or more and keeping them at least 2 feet (.6m) from other barriers will improve performance (see Figure 8). If you are remote mounting the antennas and require strong signal over a large area, consider using highly directional antennas such as a log-periodic. The ALP-450 available from T ...

  • Telex FMR-10 - page 13

    3.2 Handheld T ransmitter Setup 3.2 Handheld T ransmitter Setup 1. Insert battery. Slide open the hinged battery compartment cover by placing your thumb on the indents of the battery door (at the bottom of the transmitter) and gently pushing down (see Figure 9). Insert the battery, terminal end first, into the compartment, with the smaller positive ...

  • Telex FMR-10 - page 14

    4. Verify Reception. When the transmitter is turned on: (FMR-10) the RF meter will illuminate, indicating that the receiver is pick - ing up the signal. If this does not happen, make sure that the trans - mitter and receiver are set to the same channels. 5. Unmute the audio by sliding the audio switch (immediately be - low the mic element) towards ...

  • Telex FMR-10 - page 15

    3.3 Bodypack T ransmitter Setup T ransmitter Setup 1. Insert battery. Open the hinged battery compartment by placing your thumb or finger on the indent labeled OPEN on the battery door and pushing down, see Figure 11. When inserting the bat - tery, pay attention to the polarity (+/-) and insert the terminals into the battery compartment first. Clos ...

  • Telex FMR-10 - page 16

    3. Turn on the transmitter by sliding the power switch to its on po - sition. Check the condition of the battery by watching the light below the power switch. The red battery light should flash once and then go out. If the light stays on, the battery is weak and should be replaced. 4. Verify reception. When the transmitter is turned on: (FMR-10) th ...

  • Telex FMR-10 - page 17

    8. Adjust the transmit gain if necessary. Gently insert the pro - vided screwdriver or other 3/32-in. 2.4mm screwdriver into the gain adjustment located at the top edge of the battery compart - ment under the door (see Figure 11). The door has to be opened but not swung upward to make adjustments. Turn lightly until the screwdriver tip drops into t ...

  • Telex FMR-10 - page 18

    4. Guidelines/Recommendations for Best Performance Compatibility The receiver and transmitter must be set to the same channel to oper - ate together. Using Multiple Wir eless Systems Using Multiple Wir eless Systems If two or more FMR-10 Wireless and/or other VHF/UHF wireless systems are being used in the same location, proper frequency coordi - na ...

  • Telex FMR-10 - page 19

    Multiple System Setup & Multiple System Setup & ClearScan™ ClearScan ™ is most useful for finding operating frequencies for situ - ations where no more than 2 systems will be used simultaneously. When setting up more than 2 systems, use ClearScan ™ to choose the first channel of operation. Set up subsequent systems following the chann ...

  • Telex FMR-10 - page 20

    Battery Recommendations Battery Recommendations Fresh 9-volt alkaline batteries from a quality manufacturer will yield the best performance from your FMR-10 transmitters. Rechargeable 8.4-volt Ni-cad batteries can be used, but will yield much shorter op - erational time. When the transmitter switch is turned on, the red battery light will flash onc ...

  • Telex FMR-10 - page 21

    -19- 5. T roubleshooting Guide Problem Possible Causes Solutions No audio & no lights on receiver No audio & no Tx ON light on receiver No audio Low audio signal Distorted audio signal Interference Short range or drop-outs Receiver is off Transmitter is off No (or dead) battery in transmitter Faulty battery contacts in transmitter Transmitt ...

  • Telex FMR-10 - page 22

    6. FMR-10 Wir eless Series System T echnical Specifications UHF Receivers: UHF Receivers: FMR-10 Receiver UHF T ransmitters: UHF T ransmitters: WT-10 and HT-10D and HT-10D -20- Receiver Type Synthesized PLL Frequency Range (RF) Selected Frequencies between 710-866 MHz (depending on Country of Operation) Number of Selectable Channels 10 Diversity Tr ...

  • Telex FMR-10 - page 23

    -21- FCC INFORMATION The TELEX Receiver FMR-10 is authorized under Part 15 of the Federal Communication Commission. The Telex WT-10 and HT-10D Transmitters are type Ac - cepted under United States Federal Communications Com - mission Part 74. Licensing of Telex equipment is the user’s responsibility and licensability depends upon the user’s cla ...

  • Telex FMR-10 - page 24

    ACCESSORIES AND REPLACEMENT PARTS Order No. Description 450131 Plastic belt clip for bodypack 63850006 WLM-50 tie clip-horizontal 63850007 WLM-50 tie clip-vertical 64277000 WLM-50 omnidirectional lapel microphone 57013001 WLM-50 foam windscreen 70925001 ELM-22 MicroMini ™ omnidirectional lapel mic 70928001 ELM-22 mic clip 57013001 ELM-22 foam win ...

  • Telex FMR-10 - page 25

    ...

  • Telex FMR-10 - page 26

    R PN 803341 May 2001 Telex Communications Inc., 12000 Portland Ave. South, Bur nsville, MN 55337 (952) 884-4051, (800) 828-6107, Fax: (952) 887-9212 ...

Fabricant Telex Catégorie Microphone

Les documents que nous recevons du fabricant de l'appareilTelex FMR-10 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Telex
- manuels d’utilisations FMR-10
- fiches produit Telex
- dépliants
- ou étiquettes-énergie Telex FMR-10
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Telex FMR-10.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Telex FMR-10, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Telex FMR-10. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Telex FMR-10.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Telex FMR-10, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Telex FMR-10 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Telex FMR-10.

Le manuel d’utilisation complet Telex, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Telex FMR-10 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Telex FMR-10, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lTelex FMR-10 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Telex FMR-10 - qui devraient nous aider dans les premières étapes lors de l'utilisation Telex FMR-10
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Telex FMR-10
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Telex FMR-10 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Telex FMR-10?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Telex FMR-10, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Telex FMR-10 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)