Français dropdown-ico

Manuel d’utilisation MTD 615

28 pages 12.13 mb
Télécharger

Aller à la page of 28

Summary
  • MTD 615 - page 1

    IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y MTD PR ODUCTS INC. P .O . BO X 368022 CLEVELAND , OHIO 44136-9722 MODELS 615 E645E E665E Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covered or grass-covered land unless the engine’s exhaust s ...

  • MTD 615 - page 2

    2 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY ...

  • MTD 615 - page 3

    3 • If the snow thrower should start to vibrate abnormally, stop the engine and check immediately for the cause. Vibration is generally a warning of trouble. • Stop engine whenever you leave the operating position, before unclogging the collector/impeller housing or discharge guide, and making any repairs, adjustments, or inspections. Never pla ...

  • MTD 615 - page 4

    4 SECTION 2: FINDING YOUR MODEL NUMBER This Operators Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain your snow thrower. Please read and understand what it says. Before you start to prepare your snow thrower for its first use, please locate the model plate and copy the information from it in thi ...

  • MTD 615 - page 5

    5 SECTION 4: CONTENTS OF HARDWARE PACK La y out the hardware according to the illustration f or identification pur poses. Part numbers are shown in parentheses. (Hardware pac k may contain e xtra items which are not used on y our unit.) A ATTACHING THE HANDLES (2)Hex Bolts (A) (710-3180) (4)Lock Washers (C) (736-0119) (2) Saddle (I) (784-5599) (2) ...

  • MTD 615 - page 6

    6 SECTION 5: ASSEMBLY INSTRUCTIONS IMPORTANT: After assembly, service engine with gasoline, and check oil level as instructed in the separate engine manual packed with your unit. NOTE: References to right or left side of the snow thrower are determined from behind the unit in the operating position. UNP A CKING • Remove staples or break glue on t ...

  • MTD 615 - page 7

    7 ASSEMBLING THE HANDLES AND HANDLE P ANEL (Hard ware B) 1. Raise both clutch grips. 2. Lower left and right handles down through handle panel between the pivot rod and the clutch grips and attach using hardware B. See Figure 2. Figure 2 3. Do not tighten at this time. 4. Lay handle panel assembly behind snow thrower. See Figure 3. Figure 3 5. Inse ...

  • MTD 615 - page 8

    8 A TT A CHING THE CLUTCH CABLES (Hard ware D) 1. Thread hex nuts (J) onto the “Z” fittings (R) (see inset,). Insert “Z” fitting into hole in clutch grips. See Figure 6. Figure 6 2. Route the left cable between engine and speed selector plate and then between handle panel and clutch lever pivot rod before threading onto the left “Z” fit ...

  • MTD 615 - page 9

    9 3. Thread one hex nut (D) onto the eyebolt on the chute crank assembly until there is at least two inches of threads showing between the nut and the head of the eyebolt. See Figure 10. Figure 10 4. Place the eyebolt into the hole located half way up the left handle. Secure with cupped washer (N) (cupped side against the handle, see inset, Figure ...

  • MTD 615 - page 10

    10 ADJUSTING THE SKID SHOES The space between the shave plate and the ground can be adjusted. For close snow removal on a smooth surface, raise the skid shoes into a high position on the auger housing. Use a middle or lower position when the area to be cleared is uneven. See Figure 13. Figure 13 Adjust skid shoes by loosening the four hex nuts and ...

  • MTD 615 - page 11

    11 THRO TTLE CONTROL (See Figure 15) The throttle control is located on the engine. It regulates the speed of the engine. SAFETY IGNITION KEY (See Figure 15) The ignition key must be inserted in the switch before the unit will start. Remove the ignition key when snow thrower is not in use. FUEL CUT OFF V AL VE The fuel cutoff valve, located under t ...

  • MTD 615 - page 12

    12 Electric Starter WARNING: The optional electric starter is equipped with a three-wire power cord and plug, and is designed to operate on 120 volt AC household current. It must be properly grounded at all times to avoid the possibility of electric shock which may be injurious to the operator. Follow all instructions carefully. Determine that your ...

  • MTD 615 - page 13

    13 T O ENGA GE DRIVE 1. With the engine running near top speed, move shift lever into one of the five FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist. Use the slower speeds until you are familiar with the operation of the snow thrower. 2. Squeeze the auger clutch grip and the augers will tur ...

  • MTD 615 - page 14

    14 NOTE: If you placed plastic under the gas cap, be certain to remove it. A UGER CLUTCH ADJUSTMENT To adjust the auger clutch, refer to Final Assembly and Adjustments section on page 9. CARBURET OR ADJUSTMENT WARNING: If any adjustments are made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful ...

  • MTD 615 - page 15

    15 DRIVE AND SHIFTING MECHANISM Remove rear cover. Oil any chains, sprockets, gears, bearings, shafts, and shifting mechanism at least once a season. Use engine oil or a spray lubricant. Avoid getting oil on rubber friction wheel and aluminum drive plate. GEAR CASE The worm gear case has been filled with grease at the factory. If disassembled for a ...

  • MTD 615 - page 16

    16 Figure 23 7. Unhook the support bracket spring from the frame. NOTE: It may be necessary to loosen the six nuts that connect the frame to the auger housing to aid in belt removal. 8. Lift the rear auger belt from the auger pulley, and slip belt between the support bracket and the auger pulley. See Figure 23. Repeat this step for the front auger ...

  • MTD 615 - page 17

    17 7. Slide the gear shaft to the right, then slide the friction wheel assembly from the shaft. 8. Remove the six screws from the friction wheel assembly (three from each side). Remove the friction wheel rubber from between the friction wheel plate. 9. Reassemble new friction wheel rubber to the friction wheel assembly, tightening the six screws in ...

  • MTD 615 - page 18

    18 SECTION 12: TROUBLE SHOOTING GUIDE Note: For repairs beyond the minor adjustments above, contact your local authorized service dealer. T rouble P ossible Cause(s) Corrective Action Engine f ails to star t Fuel tank empty , or stale fuel. Block ed fuel line. Choke not in ON position F aulty spark plug. K ey not in s witch on engine. Spark plug wi ...

  • MTD 615 - page 19

    19 SECTION 13: ILLUSTRATED PARTS GEAR ASSEMBLY Ref. No. P ar t No. Description Ref. No. P ar t No. Description 1 618-0123 Housing—L.H. 11 721-0327 Seal-Oil 2 618-0124 Housing—R.H. 12 721-0328 Locktite 5699 3 710-0642 Screw 13 736-0351 W asher-Flat 4 711-1020 Spiral Axle 22" 14 736-0369 W asher-Flat 711-0908 Spiral Axle 24" 15 736-0445 ...

  • MTD 615 - page 20

    20 HANDLE ASSEMBLY 57 ...

  • MTD 615 - page 21

    21 HANDLE ASSEMBLY Ref. No. Part No. Description Ref. No. Part No. Description 1 784-5717 Control P anel Ass’y (615) 33 784-5599 Handle T ab 784-5718 Control P anel Ass’y (E645, E665) 34 720-0274 Grip 2 710-0788 He x Bolt 1/4-20 x 1.00 35 749-0910A Handle RH Black 3 705-5233 Clutch Le ver LH 36 749-0911A Handle LH Black 4 705-5234 Clutch Le ver ...

  • MTD 615 - page 22

    22 BLOWER HOUSING ...

  • MTD 615 - page 23

    23 Ref. No. P art No. Description Ref. No. P art No. Description 1 784-5618 Housing, Bearing 24 715-0114 Spring Pin 2 05931 Housing, Bearing 25 731-1379 Adapter , Chute 3 618-0152 Gear Assembly (22") 26 732-0611 Spring 618-0120 Gear Assemb ly (24") 27 736-0119 Loc k W asher 4 684-0052 22" Housing Assembly 28 736-0167 W asher , Flat 6 ...

  • MTD 615 - page 24

    24 FRAME ASSEMBLY ...

  • MTD 615 - page 25

    25 FRAME ASSEMBLY †Used with 13" Wheels ††Used with 16" Wheels WHEEL ASSEMBLIES Ref. No. Part No. Description Ref. No. Part No. Description 1 618-0063 Bear ing Ass’y . 25 736-0242 W asher, Bell 2 656-0012A Ass’y ., Friction Wheel Disc 30 Lubricant 3 684-0013 Rod Shift, Wheel Driv e 31 738-0869 Axle† 4 684-0021 Br kt. Ass’y . ...

  • MTD 615 - page 26

    26 ENGINE AND “V” BELTS Ref. No. P art No. Description Ref. No. P art No. Description 1 05896A Brac ket 17 736-0331 W asher—Bell 2 629-0071 Cord, Extension 18 736-0505 Washer—Flat 3 710-0117 Screw 19 748-0234 Shoulder Spacer 4 710-0157 Screw 20 748-0360 Pulley , Adapter 5 710-0230 Screw 21 754-0346 V -Belt 6 710-0342 Screw 22 754-0430 V -Be ...

  • MTD 615 - page 27

    27 ENGINE AND “V” BELTS Ref. No. P art No. Description Ref. No. P art No. Description 1 05896A Brac ket-Idler 16 736-0329 W asher-Lock 2 629-0071 Cord-Extension 110V† 17 736-0331 Washer-Loc k 3 710-0117 Screw-He x 18 736-0505 W asher-Flat 4 710-0157 Screw-He x 19 736-0507 W asher 5 710-0230 Screw-He x 20 748-0234 Spacer 6 710-0342 Screw-He x ...

  • MTD 615 - page 28

    MANUF A CTURER’S LIMITED W ARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship. This warranty covers u ...

Fabricant MTD Catégorie Snow Blower

Les documents que nous recevons du fabricant de l'appareilMTD 615 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques MTD
- manuels d’utilisations 615
- fiches produit MTD
- dépliants
- ou étiquettes-énergie MTD 615
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation MTD 615.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation MTD 615, manuels d’entretien, brefs manuels ou manuels de l’utilisateur MTD 615. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit MTD 615.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil MTD 615, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser MTD 615 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs MTD 615.

Le manuel d’utilisation complet MTD, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel MTD 615 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières MTD 615, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lMTD 615 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil MTD 615 - qui devraient nous aider dans les premières étapes lors de l'utilisation MTD 615
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de MTD 615
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service MTD 615 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de MTD 615?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec MTD 615, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec MTD 615 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)