-
Porter-Cable 3802L - page 1
ESP AÑOL: PÁGINA 23 FRANÇAISE : P AGE 43 12" Compound Laser Miter Saw Instruction Manual Part No. 906984 - 07-20-04 The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. _____________________________________ T ype _____________________ ...
-
Porter-Cable 3802L - page 2
2 T ABLE OF CONTENTS IMPORT ANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 GENERAL SAFETY R ...
-
Porter-Cable 3802L - page 3
3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...
-
Porter-Cable 3802L - page 4
4 GENERAL SAFETY RULES READ AND UNDERST AND ALL WARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may r esult in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ INSTRUCTION MANUAL BEFORE OPERA TIN ...
-
Porter-Cable 3802L - page 5
5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJURY . 1 . DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE from your supervisor, instructor , or another qualified person if you are not familiar with the operation of this machine. 3. FOLLOW ALL WIRING CODES and rec ...
-
Porter-Cable 3802L - page 6
Use proper extension cor ds. Make sure your extension cord is in good condition. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cor d will cause a drop in line voltage, r esulting in loss of power and overheating. Fig. D, shows the correct gauge to use depending on the cord length. ...
-
Porter-Cable 3802L - page 7
7 1. Carefully r emove the machine from the carton. Retain all packing materials until you have inspected and satisfactorily operated the machine. Do not operate this machine until you read and understand the entir e instruction manual. 2. Place the machine on a firm, level surface with extra room for handling and pr oper support of the workpiece. ...
-
Porter-Cable 3802L - page 8
8 MOVING CUTTINGHEAD TO THE UP POSITION 1. Pull out the cuttinghead lockpin (A) Fig. 4, and move the cuttinghead (B) to the up position. 2. Fig. 5 illustrates the lockpin (A) pulled out and the cuttinghead (B) in the up position. A Fig. 4 Fig. 5 B A B MOVING T ABLE TO THE 0° CUT -OFF POSITION 1. Rotate locking knob (A) Fig. 6 counter -clockwise as ...
-
Porter-Cable 3802L - page 9
9 4. Attach the fence slide support (E) Fig. 11 to the extension table (B) by using the two 5/16-18 x1-1/4” hex head screws, 5/16” lockwashers, and 5/16” flat washers (F). Insert the two screws up thr ough the two holes (G) in the table extension and thread them into the two thr eaded holes (H) on the bottom of the fence slide support. NOTE: ...
-
Porter-Cable 3802L - page 10
1. This miter saw will cut any angle from 0° to 47° right and left. T urn the locking knob (A) Fig. 21 counter -clockwise, depr ess the lock lever (B), and rotate the table. 2. The compound miter saw is equipped with positive stops at 0°, 15°, 22.5°, 31.62°, and 45° left and right. 3. The center line (C) Fig. 22 on the cursor indicates the a ...
-
Porter-Cable 3802L - page 11
T o adjust the sliding fit between the movable table and the base, turn the nut (A) Fig. 23 clockwise to increase the sliding fit (opposite to decrease the fit). This adjustment should not be so tight that it restricts the r otating movement of the table, or so loose that it affects the accuracy of the saw . 11 A B C E D B DISCONNECT THE MACHINE FR ...
-
Porter-Cable 3802L - page 12
12 TIL TING CUTTINGHEAD FOR BEVEL CUTTING DISCONNECT THE MACHINE FROM THE POWER SOURCE. IMPORT ANT : Move the sliding fence to the left to provide clearance for the blade and guard. The degr ee of tilt determines how far to move the sliding fence. Refer to the section “ADJUSTING SLIDING FENCE.” 1. The cuttinghead can be tilted to cut any bevel ...
-
Porter-Cable 3802L - page 13
13 1. Adjust the saw so that both the bevel and miter pointers are set at 0°. Tighten the bevel lock handle and lock the cuttinghead in the down position. 2. Place one end of a square (A) Fig. 32 on the table and the other end against the blade. The blade should be 90° to the table. 3. T o adjust, loosen the bevel lock handle (H) Fig. 33. Loosen ...
-
Porter-Cable 3802L - page 14
14 ADJUSTING SLIDING FIT BETWEEN TRUNNION AND BEVEL BRACKET After a long period of time, the sliding fit between the trunnion and the bevel bracket may need to be adjusted. Adjust the sliding fit by tightening the adjusting nut (C) Fig. 36, located underneath the bevel lock (A) Fig. 36 and collar (B) Fig. 36. This adjustment should not be so tight ...
-
Porter-Cable 3802L - page 15
VERTICAL ALIGNMENT SET SCREWS 15 P ARTIAL CUT BRASS HEX NUT ADJUSTING THE DUAL LASERLOC ™ LINES Each of the laser lines have been aligned parallel to the blade at the factory and should not need any adjustment prior to use. However , left-to-right adjustment to the laser lines may be necessary if you change to a thicker or thinner kerf blade. For ...
-
Porter-Cable 3802L - page 16
16 LEFT LASER ADJUSTMENT SCREW 1. The vertical alignment is set correctly when the lines do not move horizontally (sideways) as the saw head is raised and lowered. If vertical alignment is corr ect, go to “ TO SET LEFT AND RIGHT KERF ADJUSTMENT” . 2. T o adjust, turn the left and right kerf adjustment screws one half turn clockwise. T ake of f ...
-
Porter-Cable 3802L - page 17
FENCE FENCE BLADE BLADE CORRECT INCORRECT 17 AUXILIAR Y WOOD FENCE When performing multiple or repetitive cut-of f operations that result in small cut-of f pieces (one inch or less), the saw blade can catch the cut-off pieces and pr oject them out of the machine or into the blade guard and housing, possibly causing damage and/or injury . In order t ...
-
Porter-Cable 3802L - page 18
18 A C 2 1 B D 1 2 Fig. 47 Fig. 48 CORRECT INCORRECT CUTTING BOWED MA TERIAL 1. If the material is bowed, position it on the table as shown in Fig. 43. 2. If the material is positioned the wr ong way (Fig. 44), the workpiece will pinch the blade near the completion of the cut. One of the many features of the saw is the ease of cutting cr own mouldi ...
-
Porter-Cable 3802L - page 19
19 For support when cutting long pieces, a work support extension can be constructed. Fig. 49 illustrates the miter saw mounted to two standard 2 x 4’ s (A). Fasten the four mounting legs (two of which are shown at (B) Fig. 49) to the 2 x 4’ s, using four screws (not supplied) thr ough the four holes in the mounting legs. The length of the 2 x ...
-
Porter-Cable 3802L - page 20
20 BRUSH INSPECTION AND REPLACEMENT BEFORE INSPECTING OR REMOVING BRUSHES, DISCONNECT THE MACHINE FROM THE POWER SOURCE. Brush life varies, depends on the load on the motor . Check the brushes after the first 50 hours of use of a new machine, or after a new set of brushes has been installed. After the first check, examine them after about 10 hours ...
-
Porter-Cable 3802L - page 21
21 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air . F AILURE TO ST AR T Should your tool fai ...
-
Porter-Cable 3802L - page 22
22 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original pur chase. W e will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, pr oves to be defective in workmanship or materi ...
-
Porter-Cable 3802L - page 23
The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ...
Avez-vous une question à propos de Porter-Cable 3802L?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Porter-Cable 3802L, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Porter-Cable 3802L il est probable qu’il a envie de partager la façon de le résoudre.