Manuel d’utilisation Apple Drive Interconnect Board

11 pages 0.28 mb
Télécharger

Aller à la page of 11

Summary
  • Apple Drive Interconnect Board - page 1

    073-0673 Re v . C  Xserve Drive Interconnect Board Replacement Instructions F ollow the instructions in this sheet carefully . F ailure to f ollo w these instructions could damage your equipment and v oid its w arranty . Note: Online instructions covering customer-installab le par ts are av ailab le at http://www .info .apple.com/installpar ts/. ...

  • Apple Drive Interconnect Board - page 2

    Xserve Drive Interconnect Board - 2 4. If the ser v er is in the loc k ed position (the y ellow security LED on the front panel is on), use the Allen ke y that came with the server to unloc k it. 5. If the cable management arm is not in use, unplug all e xternal cables e xcept the power cord. 6. T ouch the ser ver’ s metal case to discharge any s ...

  • Apple Drive Interconnect Board - page 3

    Xserve Drive Interconnect Board - 3 9. Grasp the thumbscre ws and slide the bottom housing f orward part wa y to e xpose the two chassis le v ers . (Figure 2) 10. While depressing both le v ers , pull the bottom housing all the w a y forw ard and remo v e it from the rac k. Figure 2 11. Place the bottom housing on a sturdy , flat surf ace and ESD ...

  • Apple Drive Interconnect Board - page 4

    Xserve Drive Interconnect Board - 4 F or each installed drive , do the f ollowing: 1. Press the handle on the front of the drive module so the handle pops out. (Figure 3) Figure 3 2. Grasp the drive handle , and pull the drive module out of the server . (Figure 4) Figure 4 ...

  • Apple Drive Interconnect Board - page 5

    Xserve Drive Interconnect Board - 5 Blowers 1. Disconnect the cable f or the r ight blo wer from the driv e interconnect board. (Figure 5) 2. Lift the right blow er straight up off its mounting pegs and remo v e it from the ser v er . 3. Repeat steps 1 and 2 f or the left blo wer . Figure 5 ...

  • Apple Drive Interconnect Board - page 6

    Xserve Drive Interconnect Board - 6 Heatsink Duct Note: There are two versions of Xserve. If your v ersion does not include a plastic duct ov er the heatsink, skip to “A T A Controller Board” on the f ollo wing page. 1. Release the latch on the heatsink duct from its slot, slide the duct aw a y from the blo wer , and lift the end of the duct as ...

  • Apple Drive Interconnect Board - page 7

    Xserve Drive Interconnect Board - 7 A T A Controller Board 1. Press in on both ends of the clip securing the r ight side of the A T A controller board and remov e the clip from the server . Repeat f or the clip on the left side of the board. 2. Lift the A T A controller board straight up to disconnect it from the drive interconnect and logic boards ...

  • Apple Drive Interconnect Board - page 8

    Xserve Drive Interconnect Board - 8 Drive Inter connect Board 1. Disconnect the f ollowing cab les from the drive interconnect board: (Figure 8) • optical drive cable • power supply cable • locking switch cable • front panel board cable • FireWire cable Figure 8 2. Release the three thumbscrews that secure the driv e interconnect board to ...

  • Apple Drive Interconnect Board - page 9

    Xserve Drive Interconnect Board - 9 Installing the Replacement Driv e Inter connect Board 1. Install the replacement drive interconnect board on the two mounting pegs in the chassis. (Figure 10) 2. Check that the board engages with the three br ack ets on the chassis . 3. Press the board fir mly to ward the front of the server , and tighten the th ...

  • Apple Drive Interconnect Board - page 10

    Xserve Drive Interconnect Board - 10 5. Reconnect the A T A controller board to the dr iv e interconnect and logic boards. Note: When replacing the ATA controller board, align it over the two pairs of connectors on the drive interconnect and logic boards, making sure the “MLB” arrow points toward the logic board, and press down. (Figure 12) Fig ...

  • Apple Drive Interconnect Board - page 11

    Xserve Drive Interconnect Board - 11 7. If you remo v ed it earlier , replace the heatsink duct on the heatsink. 8. Reinstall the blo wers . 9. Reinstall the hard drives. Closing the Serv er 1. Carefully slide the bottom housing back into the r ack. 2. Tighten the front thumbscrews to secure it. W arning: Never turn on the server unless all of its ...

Fabricant Apple Catégorie Computer Hardware

Les documents que nous recevons du fabricant de l'appareilApple Drive Interconnect Board peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Apple
- manuels d’utilisations Drive Interconnect Board
- fiches produit Apple
- dépliants
- ou étiquettes-énergie Apple Drive Interconnect Board
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Apple Drive Interconnect Board.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Apple Drive Interconnect Board, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Apple Drive Interconnect Board. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Apple Drive Interconnect Board.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Apple Drive Interconnect Board, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Apple Drive Interconnect Board par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Apple Drive Interconnect Board.

Le manuel d’utilisation complet Apple, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Apple Drive Interconnect Board - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Apple Drive Interconnect Board, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lApple Drive Interconnect Board qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Apple Drive Interconnect Board - qui devraient nous aider dans les premières étapes lors de l'utilisation Apple Drive Interconnect Board
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Apple Drive Interconnect Board
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Apple Drive Interconnect Board dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Apple Drive Interconnect Board?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Apple Drive Interconnect Board, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Apple Drive Interconnect Board il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)