Italiano dropdown-ico

Manuale per l’uso Beckett CULUS CF1400

24 pagine 1.5 mb
Scarica

Vai alla pagina of 24

Summary
  • Beckett CULUS CF1400 - page 1

    COMMERCIAL PRODUCT S Potential for Fire, Smoke and Asphyxiation Hazards T o the Homeowner or Equipment Owner: Please read and carefully follow all instructions provided in this manual regarding your responsibilities in caring for your heating equipment. Contact a professional, quali fi ed service agency for installation, start-up or service work. ...

  • Beckett CULUS CF1400 - page 2

    2 Special Requirements - The installation of a burner shall be in accordance with the regulations of authorities having Jurisdiction. For recommended installation practices in the U.S. refer to the latest edition of NFP A 31. (CSA-B139 and CSA-B140 in Canada. ○ Impaired Burner Performance & Fire Hazard Do NOT operate the burner beyond speci ? ...

  • Beckett CULUS CF1400 - page 3

    3 CF1400/CF2300 Burner Manual Owner ’ s Responsibility: Service Agency Responsibility: Follow these instructions exactly . Failure to follow these instructions, misuse, or incorrect adjustment of the burner could result in asphyxiation, explosion or fi re. Contact a professional, quali fi ed service agency for the installation, adjustment and s ...

  • Beckett CULUS CF1400 - page 4

    4 Pr e-Installa tion Checklist Combustion Air Supply The fuel supply piping and tank must provide #1 or #2 fuel oil at pressure or vacuum conditions suitable for the fuel unit (oil pump) on the burner . Refer to fuel unit literature in the literature envelope in the burner carton to verify allowable suction pressure. If fuel supply is level with or ...

  • Beckett CULUS CF1400 - page 5

    5 CF1400/CF2300 Burner Manual The fuel unit nozzle port pressure is factory set at 300 psig. Some original equipment manufacturer burner applications may call for a lower pressure to obtain a required fi ring rate. Do not change this pressure unless directed to do so by the appliance manufacturer . Electrical Supply V erify that the power connecti ...

  • Beckett CULUS CF1400 - page 6

    6 Model Firing Rate (gph) Minimum Dimensions Refractory Lined Wet-based Boilers HLHL CF1400 0 to 5 7.0” 25.0” 7.0” 25.0” 5 to 10 8.0” 35.0” 8.0” 40.0” CF2300 5 to 10 8.0” 35.0” 8.0” 40.0” 10 to 15 9.0” 40.0” 9.0” 50.0” 15 to 20 1 1.0” 55.0” 1 1.0” 60.0” Note: 10% turndown indicates suf fi cient reserve air t ...

  • Beckett CULUS CF1400 - page 7

    7 CF1400/CF2300 Burner Manual Stray Light The control must detect a dark, no- fl ame condition in order to start the burner or it will hold in the stray light lockout mode. Shield the burner view window from direct exposure to intense light. ○ ○ Mount the Bur ner Mount Flange(s) on Air T ube This section does not apply to burners with welded ? ...

  • Beckett CULUS CF1400 - page 8

    8 Figure 5 – Nozzle and Nozzle Line Assembly Figure 6 – Nozzle Line Assembly in Burner Mount Air T ube to Burner Remove the rear access door from the back of the burner for improved access to the interior . Attach the air tube to the burner with the bolts and acorn nuts provided. The acorn nuts must go on the outside of the burner , with the bo ...

  • Beckett CULUS CF1400 - page 9

    9 CF1400/CF2300 Burner Manual Set “Z” Dimension Replace the rear access door on the burner , making sure that the adjusting plate assembly is seated in the recessed area in the housing. Loosen acorn nut (item c ) and spline nut (item b ). Move nozzle line forward to the maximum head setting #9 and tighten acorn nut (item c ). Loosen acorn nut ( ...

  • Beckett CULUS CF1400 - page 10

    10 Special Note: The burner is shipped with a by- pass plug installed in the fuel unit. For low/high operation, the by-pass plug must be left in the fuel unit, regardless of the fuel system used (one-pipe with by-pass loop or two-pipe). Do not remove the by-pass plug. One-pipe Oil System By-pass Loop Refer to Figure 9 (item m ). Note the addition o ...

  • Beckett CULUS CF1400 - page 11

    11 CF1400/CF2300 Burner Manual Low- fi re/high- fi re operation – The fuel unit nozzle port pressure is factory set at 300 psig. At high fi re, full pressure (300 psig) is applied at the oil nozzle, causing full input. At low fi re, the by-passing is done inside the fuel unit when the by-pass valve operates. This by-passing of oil reduces the ...

  • Beckett CULUS CF1400 - page 12

    12 2 1 3 5 6 8 4 7 Standby Motor -off delay V alve-on delay T rial for ignition Ignition carryover Run Lockout Recycle 9 Pump prime Run : With a fl ame established and the control continuing to detect a fl ame, the burner will operate in the RUN Mode until the load demand is satis fi ed or a limit opens. If terminals RC1 and RC2 are jumpered, th ...

  • Beckett CULUS CF1400 - page 13

    13 CF1400/CF2300 Burner Manual Figure 13 – T ypical Wiring (7505P) Section: Wire the Burner ...

  • Beckett CULUS CF1400 - page 14

    14 Figure 14 – T ypical Wiring (R7184B) T ypical Burner Sequence of Operation - 7184B Control Refer to the appliance manufacturer ’s wiring diagram for actual speci fi cations. Standby — The burner is idle, waiting for a call for heat. When a call for heat is initiated, there is a 3- to 10-second delay while the control performs a safe start ...

  • Beckett CULUS CF1400 - page 15

    15 CF1400/CF2300 Burner Manual Pr epare the Bur ner f or Star t-up Start-up checklist V erify the following before attempting to start burner . Combustion air supply and venting have been inspected and veri fi ed to be free of obstructions and installed in accordance with all applicable codes. Fuel unit by-pass plug has not been installed for one- ...

  • Beckett CULUS CF1400 - page 16

    16 Figure 16 – Adjusting Plate Initial Setting, Typical T able 4A – CF1400 Initial Indicator Adjustment Plate Settings CF1400 T ube Head Position Damper Position Approximate Head Setting Firing Rate (gph) Approximate Air Damper Setting Firing Rate (gph) A 0 4.00 0 -- 1 4.50 10 -- 2 5.00 20 4.00 3 6.00 30 5.00 4 7.00 40 7.00 5 7.50 50 8.00 6 8.0 ...

  • Beckett CULUS CF1400 - page 17

    17 CF1400/CF2300 Burner Manual Initial Air Settings If your burner was built for a speci fi c OEM (Original Equipment Manufacturer) application, the “Mfr ’s Settings” label (see Figure 1 ) will indicate the application and the initial air settings made at Beckett. Please verify those settings using the following procedure. If your burner was ...

  • Beckett CULUS CF1400 - page 18

    18 Star t the Bur ner Start Burner and V ent Air From Oil Line Disable Function Any time the motor is running, press and hold the reset button to disable the burner . The burner will remain of f as long as the button is held and will return to standby when released. Cad Cell Resistance Measurement: If the Beckett 7505 control is equipped with the G ...

  • Beckett CULUS CF1400 - page 19

    19 CF1400/CF2300 Burner Manual Place the low- fi re hold switch in the high- fi re position . The damper motor will begin to rotate after four seconds. Use combustion test instruments to adjust the burner . Adjust the air by moving the red cam to a lower number until a trace of smoke is achieved with CO 2 level as high as possible (lowest possibl ...

  • Beckett CULUS CF1400 - page 20

    20 Annual Service Replace the oil supply line fi lter . The line fi lter cartridge must be replaced to avoid contamination of the fuel unit and nozzle. Inspect the oil supply system. All fi ttings should be leak-tight. The supply lines should be free of water , sludge and other restrictions. Remove and clean the pump strainer if applicable. Repl ...

  • Beckett CULUS CF1400 - page 21

    21 CF1400/CF2300 Burner Manual SK9930 3 2 4 5 6 1 SK9931 8 9 7 Section: Replacement Parts Figure 19a – Burner Replacement Parts ...

  • Beckett CULUS CF1400 - page 22

    22 Item Part Name Description CF1400 Part No. CF2300 Part No. 1 Oil V alve Mounted on Junction Box 21789U 21789U 2 Knurled Nut All models 3666 3666 3 Adjusting plate assembly w/ cast aluminum door w/ stamped sheet-metal door 51213U 5201701U 51213U 5201701U 4 Fuel pump B2T A-8245 21313U 21313U 5 Damper motor 2-stage 750601U 750601U 6 Fuel lines Spec ...

  • Beckett CULUS CF1400 - page 23

    23 CF1400/CF2300 Burner Manual Figure 19b – Burner Replacement Parts (Continued) SK9936 SK9932 SK9930 14 13 12 10 20 11 21 22 23 15 16 17 18 19 ...

  • Beckett CULUS CF1400 - page 24

    USA: P .O. Box 1289 ● Elyria, Ohio 44036 Canada: R.W . Beckett Canada, Ltd. ● Unit #3, 430 Laird Road ● Guelph, Ontario N1G 3X7 www .beckettcorp.com Part Number 6104 BCF23 R14, Printed in the U.S.A. 08/10 The R. W . BECKETT CORPORA TION (“Beckett”) warrants to persons who purchase its “Products” from Beckett for resale, or for incorpo ...

Fabbricante Beckett Categoria Burner

I documenti che otteniamo dal fabbricante del dispositivoBeckett CULUS CF1400 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Beckett
- manuali per l’uso CULUS CF1400
- schede prodotto Beckett
- opuscoli
- o etichette energetiche Beckett CULUS CF1400
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Beckett CULUS CF1400.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Beckett CULUS CF1400, manuali di manutenzione, brevi manuali o manuali utente Beckett CULUS CF1400. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Beckett CULUS CF1400.

Manuali per l’uso simili

Manuale completo del dispositivo Beckett CULUS CF1400, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Beckett CULUS CF1400 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Beckett CULUS CF1400.

Il manuale per l’uso completo Beckett, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Beckett CULUS CF1400 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Beckett CULUS CF1400, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Beckett CULUS CF1400 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Beckett CULUS CF1400 - che ci dovrebbe aiutare nei primi passi durante l'uso Beckett CULUS CF1400
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Beckett CULUS CF1400
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Beckett CULUS CF1400 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Beckett CULUS CF1400?

Utilizza il modulo sottostante

Se non hai risolto il problema con Beckett CULUS CF1400 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Beckett CULUS CF1400 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)