Italiano dropdown-ico

Manuale per l’uso Axis Communications P3225-LV

63 pagine 0.99 mb
Scarica

Vai alla pagina of 63

Summary
  • Axis Communications P3225-LV - page 1

    AXIS P3225-L V Network Camera User Manual ...

  • Axis Communications P3225-LV - page 2

    About this Document This manual is intended for administrators and users of AXIS P3225-LV Network Camera, and is applicable to rmware 5.70 and later . It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems ...

  • Axis Communications P3225-LV - page 3

    be connected using a shielded network cable (STP) that is properly grounded. Japan こ の 装 置 は 、 ク ラ ス B 情 報 技 術 装 置 で す 。 こ の 装 置 は 、 家 庭 環 境 で使 用 す る こ と を 目 的 と し てい ま す が 、 こ の 装 置 が ラ ジ オ やテ レ ビ ジ ョ ン 受 信 機 に 近 接 ...

  • Axis Communications P3225-LV - page 4

    AXIS P3225-L V Network Camera Safety Infor mation Safety Infor mation Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury . WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury . CAUTION Indicates a hazardous situation which, if not avoi ...

  • Axis Communications P3225-LV - page 5

    AXIS P3225-L V Network Camera T able of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Other Message Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Axis Communications P3225-LV - page 6

    AXIS P3225-L V Network Camera T able of Contents Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Reset to Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Axis Communications P3225-LV - page 7

    AXIS P3225-L V Network Camera Hardware Overview Hardware Overview 1 2 3 4 5 1 Network connector (P oE) 2 SD memory card slot 3 P art number (P/N) & Serial number 4 Control button 5 Status LED indicator Connectors and Buttons For technical specications, see page 60 . Network Connector RJ45 Ethernet connector with P ower over Ethernet (P oE). ...

  • Axis Communications P3225-LV - page 8

    AXIS P3225-L V Network Camera Hardware Overview • Resetting the product to factory default settings. See page 56 . • Connecting to an AXIS Video Hosting System service. See page 49 . To connect, press and hold the button for about 3 seconds until the Status LED ashes green. • Connecting to AXIS Internet Dynamic DNS Service. See page 49 . T ...

  • Axis Communications P3225-LV - page 9

    AXIS P3225-L V Network Camera Access the Pr oduct Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are • Internet Explorer ® with Windows ® • Safari ® with OS X ® and • Chrome TM or Firefox ® wit ...

  • Axis Communications P3225-LV - page 10

    AXIS P3225-L V Network Camera Access the Pr oduct For T echnical notes on this and other topics, visit the Axis Support web at www .axis.com/techsup Set the Root P assword To access the Axis product, you must set the password for the default administrator user root . This is done in the Congure Root P assword dialog, which opens when the product ...

  • Axis Communications P3225-LV - page 11

    AXIS P3225-L V Network Camera Access the Pr oduct Set P ower Line Frequency P ower line frequency is set the rst time the Axis product is accessed and can only be changed from Plain Cong (see page 56 ) or by resetting the product to factory default. Select the power line frequency (50 Hz or 60 Hz) used at the location of the Axis product. Sel ...

  • Axis Communications P3225-LV - page 12

    AXIS P3225-L V Network Camera Access the Pr oduct 4. From the second drop-down list, select Manual Trigger . 5. Select the desired action and congure the other settings as required. For more information about action rules, see Events on page 37 . To show the manual trigger buttons in the Live View page: 1. Go to Setup > Live View Cong . 2. ...

  • Axis Communications P3225-LV - page 13

    AXIS P3225-L V Network Camera Access the Pr oduct P an and Tilt bars – Use the arrows to pan and tilt the camera view , or click on a position on the bar to steer the camera view to that position. Zoom bar – Use the arrows to zoom in and out, or click on a position on the bar to zoom to that position. The PTZ controls can be disabled under PTZ ...

  • Axis Communications P3225-LV - page 14

    AXIS P3225-L V Network Camera Media Streams Media Streams The Axis product provides several video stream formats. Y our requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, and to the list of available stream proles. Other applic ...

  • Axis Communications P3225-LV - page 15

    AXIS P3225-L V Network Camera Media Streams The AMC Control P anel can be used to congure various video settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control P anel is automatically installed on rst use, after which it can be congured. Open the AMC Control P anel from: • Windows Control P anel ...

  • Axis Communications P3225-LV - page 16

    AXIS P3225-L V Network Camera Media Streams Note • <ip>= IP addess • The Axis product supports QuickTime 6.5.1 and later . • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this. 16 ...

  • Axis Communications P3225-LV - page 17

    AXIS P3225-L V Network Camera Set Up the Product Set Up the Product The Axis product can be congured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to all set ...

  • Axis Communications P3225-LV - page 18

    AXIS P3225-L V Network Camera Video Video It is possible to congure the following video features in your Axis product: • Video stream. See page 18 . • Stream proles. See page 20 . • Camera settings. See page 20 . • View areas. See page 23 . • Overlay image. See page 23 . • Privacy mask. See page 25 . Set Up Video Streams To set up ...

  • Axis Communications P3225-LV - page 19

    AXIS P3225-L V Network Camera Video • Maximum frame rate . To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a xed amount. Alternatively , the frame rate can be set as Unlimited , which means the Axis product always delivers the highest frame rate possible under the current conditions. • Overlay settings . ...

  • Axis Communications P3225-LV - page 20

    AXIS P3225-L V Network Camera Video • Medium Zipstream strength . Medium bandwidth reduction. Limited visual quality degradation in not prioritized areas in some scenes • Highest Zipstream strength . High bandwidth reduction. Visible quality degradation in not prioritized areas in many scenes Lowest Zipstream strength is the default setting for ...

  • Axis Communications P3225-LV - page 21

    AXIS P3225-L V Network Camera Video To change capture mode, follow these steps: 1. Go to Setup > Video > Camera Settings . 2. Select the new capture mode. 3. Click Save . 4. Review and recongure all settings, for example: - View areas - Stream proles - PTZ settings including preset positions and guard tours - Privacy masks - Image overl ...

  • Axis Communications P3225-LV - page 22

    AXIS P3225-L V Network Camera Video Important Use WDR in combination with automatic exposure control. Other exposure settings could give undesirable results. Exposure Settings Congure the exposure settings to suit the image quality requirements in relation to lighting, frame rate and bandwidth considerations. Exposure value - Use the Exposure va ...

  • Axis Communications P3225-LV - page 23

    AXIS P3225-L V Network Camera Video Built-in IR Illuminations LEDs WARNING Risk of eye injury . Do not look directly into the IR LED at short distance. Since the light provided from the IR LED is outside of the visible range, it is not possible to see if it is active. Use the camera to check if the IR illumination is active. The IR illumination can ...

  • Axis Communications P3225-LV - page 24

    AXIS P3225-L V Network Camera Video An overlay text can display the current date and time, or a text string. When using a text string, modiers can be used to display information such as the current bit rate or the current frame rate. For information about available modiers, see File Naming & Date/Time Formats in the online help . It is al ...

  • Axis Communications P3225-LV - page 25

    AXIS P3225-L V Network Camera Video To select the image to use as overlay: 1. Go to Video > Overlay Image . 2. Select the image to use from the Use overlay image list and click Save . To display the overlay image: 1. Go to Video > Video Stream and select the Image tab . 2. Under Overlay Settings , select Include overlay image at the coordinat ...

  • Axis Communications P3225-LV - page 26

    AXIS P3225-L V Network Camera Video Important Adding many privacy masks may affect the product’s performance. 26 ...

  • Axis Communications P3225-LV - page 27

    AXIS P3225-L V Network Camera Configure the Live View Page Configure the Live View Page Y ou can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole. See page 20 . • Default Viewer for Browser . See page 27 . • Viewer Settings. See pag ...

  • Axis Communications P3225-LV - page 28

    AXIS P3225-L V Network Camera Configure the Live View Page • Select Enable recording button to enable recording from the Live View page. This button is available when using the AMC viewer . The recordings are saved to the location specied in the AMC Control P anel. See AXIS Media Control (AMC) on page 14 . User Dened Links To display user- ...

  • Axis Communications P3225-LV - page 29

    AXIS P3225-L V Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area. For more information on view areas, see View Area on page 23 . Preset P ositions A preset position is a saved view that can be used to quickly steer the camera to a specic posit ...

  • Axis Communications P3225-LV - page 30

    AXIS P3225-L V Network Camera PTZ (Pan Tilt Zoom) 3. Specify the pause length between runs. 4. Select an available preset position and click Apply . 5. Specify the View Time in seconds or minutes. 6. Specify the View Order or select the Random view order option. 7. Click Save . To modify or remove guard tours, go to PTZ > Guard T our , select th ...

  • Axis Communications P3225-LV - page 31

    AXIS P3225-L V Network Camera PTZ (Pan Tilt Zoom) 2. Event — The Axis product can be congured to go to a preset position when triggered by an alarm (see Events on page 37 ). The event will immediately be placed rst in the queue except when an administrator is in control. 3. Operator — Same as administrator but with lower priority 4. Guard ...

  • Axis Communications P3225-LV - page 32

    AXIS P3225-L V Network Camera Detectors Detectors Camera T ampering Camera T ampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, spray-painted or severely defocused. To send an alarm, for example an email, an action rule must be set up. To congure tampering detection: 1. Go to Detectors > Camera Ta ...

  • Axis Communications P3225-LV - page 33

    AXIS P3225-L V Network Camera Detectors Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera. Changing the orientation of the camera will also change the position of the Motion Detection Window . Set Up Motion Detect ...

  • Axis Communications P3225-LV - page 34

    AXIS P3225-L V Network Camera Detectors Note • T o trigger on small objects or movements, use several small motion detection windows rather than one large window and select a low object size. • T o avoid triggering on small objects, select a high object size. • While monitoring an area where moving objects are not expected, select a high hist ...

  • Axis Communications P3225-LV - page 35

    AXIS P3225-L V Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting. For information about available applications, down ...

  • Axis Communications P3225-LV - page 36

    AXIS P3225-L V Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings . 36 ...

  • Axis Communications P3225-LV - page 37

    AXIS P3225-L V Network Camera Events Events The Event pages allow you to congure the Axis product to perform actions when different events occur . For example, the product can start a recording or send an email notication when motion is detected. The set of conditions that denes how and when the action is triggered is called an action rule ...

  • Axis Communications P3225-LV - page 38

    AXIS P3225-L V Network Camera Events - Temperature – Trigger the rule if the temperature falls outside or inside the operating range of the product. This can for example be used to send maintenance notications. • Input Signal - Manual T rigger – Trigger the rule using the Manual Trigger button in the Live View page. See Controls on the Liv ...

  • Axis Communications P3225-LV - page 39

    AXIS P3225-L V Network Camera Events • Send SNMP T rap – Send an SNMP trap message to the operator . Make sure that SNMP is enabled and congured under System Options > Network > SNMP . • Send Video Clip – Send a video clip to a recipient. • WDR Mode – The WDR Mode can be turned on or off when the action rule is triggered. Add R ...

  • Axis Communications P3225-LV - page 40

    AXIS P3225-L V Network Camera Events HTTPS Send Images Send Notication Send Video Clip Encrypted le transfer using HyperText T ransfer Protocol Secure (HTTPS). Specify login information for the HTTPS server and validate the server’s certicate. If there is a proxy between the Axis product and the HTTPS server , also specify the proxy sett ...

  • Axis Communications P3225-LV - page 41

    AXIS P3225-L V Network Camera Events Set Up Recurrences Recurrences are used to trigger action rules repeatedly , for example every 5 minutes or every hour . To set up a recurrence: 1. Go to Events > Recurrences and click Add . 2. Enter a descriptive name and recurrence pattern. 3. Click OK . To use the recurrence in an action rule, rst selec ...

  • Axis Communications P3225-LV - page 42

    AXIS P3225-L V Network Camera Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 43 . • To set up action rules, see page 37 . • To access recordings, see Find Recordings on page 42 . • To play recordings, see Play Recording on pag ...

  • Axis Communications P3225-LV - page 43

    AXIS P3225-L V Network Camera Recordings To play a recording, follow these steps: 1. Go to Recordings > List . 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the lters. See also Find Recordings on page 42 . 3. Select the recording and click Play . The recording wil ...

  • Axis Communications P3225-LV - page 44

    AXIS P3225-L V Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. T o switch languages, go to Setup > Languages and rst upload the new language le. Browse and locate the le and click the Upload Language button. Se ...

  • Axis Communications P3225-LV - page 45

    AXIS P3225-L V Network Camera System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may ...

  • Axis Communications P3225-LV - page 46

    AXIS P3225-L V Network Camera System Options 2. Select an HTTPS certicate from the list of installed certicates. 3. Optionally , click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection P olicy for the different user groups. 5. Click Save to enable the settings. To access the Axis product via the desired ...

  • Axis Communications P3225-LV - page 47

    AXIS P3225-L V Network Camera System Options A Server/Client certicate can be self-signed or issued by a Certicate Authority (CA). A self-signed certicate offers limited protection and can be used before a CA-issued certicate has been obtained. To install a self-signed certicate: 1. Go to Setup > System Options > Security > ...

  • Axis Communications P3225-LV - page 48

    AXIS P3225-L V Network Camera System Options IPv4 Address Conguration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP . The IPv4 settings are congured under System Options > Network > TCP/IP > Basic . DHCP (Dynamic Host Conguration Protocol) allows network administ ...

  • Axis Communications P3225-LV - page 49

    AXIS P3225-L V Network Camera System Options 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar . 6. Open a browser and type http://<IP address> in the Location/Address eld. For other methods of assigning the IP address, see the document Assign an IP Address and Access the Video Stream on Axi ...

  • Axis Communications P3225-LV - page 50

    AXIS P3225-L V Network Camera System Options NTP Conguration NTP (Network Time Protocol) is used to synchronize the clock times of devices in a network. The NTP settings are congured under System Options > Network > T CP/IP > Advanced . Select Obtain NTP server address via DHCP to use the NTP settings provided by the DHCP server . To ...

  • Axis Communications P3225-LV - page 51

    AXIS P3225-L V Network Camera System Options Use manually selected NAT router - Select this option to manually select a NA T router and enter the IP address for the router in the eld. If no router is specied, the product automatically searches for NAT routers on your network. If more than one router is found, the default router is selected. A ...

  • Axis Communications P3225-LV - page 52

    AXIS P3225-L V Network Camera System Options Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message. Note If HTTPS is enabled, SNMP v1 and SNMP v2c shoul ...

  • Axis Communications P3225-LV - page 53

    AXIS P3225-L V Network Camera System Options Storage SD Card NO NO NO TICE TICE TICE To prevent data corruption, the SD card should be unmounted before removal. Note For SD card recommendations see www .axis.com The Axis product supports microSD/microSDHC/microSDXC cards. The following SD card le systems are supported: • ext4 — recommended d ...

  • Axis Communications P3225-LV - page 54

    AXIS P3225-L V Network Camera System Options To enable automatic formatting, follow these steps: 1. Open the Axis product’s webpages and go to Setup > System Options > Storage . 2. Click SD Card . 3. Under General Settings , select Autoformat to . 4. Click OK to save settings. An SD card inserted into the product can be manually formatted t ...

  • Axis Communications P3225-LV - page 55

    AXIS P3225-L V Network Camera System Options Click Restore to reset most settings to the factory default values. The following settings are not affected: • the boot protocol (DHCP or static) • the static IP address • the default router • the subnet mask • the system time • the IEEE 802.1X settings • uploaded applications are kept but ...

  • Axis Communications P3225-LV - page 56

    AXIS P3225-L V Network Camera System Options Advanced Scripting Scripting allows experienced users to customize and use their own scripts. NO NO NO TICE TICE TICE Improper use may cause unexpected behavior and loss of contact with the Axis product. Axis strongly recommends that you do not use this function unless you understand the consequences. Ax ...

  • Axis Communications P3225-LV - page 57

    AXIS P3225-L V Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version. The latest version may contain a correction that xes your particular problem. The c ...

  • Axis Communications P3225-LV - page 58

    AXIS P3225-L V Network Camera Troubleshooting The IP address is being used by another device Disconnect the Axis product from the network. Run the Ping command (in a Command/DOS window , type ping and the IP address of the product): • If you receive: Reply from <IP address>: bytes=32; time=10... this means that the IP address may already be ...

  • Axis Communications P3225-LV - page 59

    AXIS P3225-L V Network Camera Troubleshooting Installation of additional ActiveX component restricted or prohibited Congure the Axis product to use a Java applet for updating video images in your browser . Go to Setup > Live View Cong and select Java applet under Default viewer . P oor rendering of H.264 images Ensure that your graphics ca ...

  • Axis Communications P3225-LV - page 60

    AXIS P3225-L V Network Camera T echnical Specifications T echnical Specifications Camera Image sensor Progressive scan RGB CMOS 1/2.8” Lens Varifocal, 3.0–1 0.5 mm, F1.4 Horizontal angle of view 92°–34° V ertical angle of view 50°–20° Remote focus and zoom, P-Iris control, IR corrected Day and night Automatically removable infrared-cu ...

  • Axis Communications P3225-LV - page 61

    AXIS P3225-L V Network Camera T echnical Specifications Event actions File upload: FTP , SFTP , HTTP , HTTPS, network share and email Notication: email, HTTP , HTTPS, T CP and SNMP trap Video recording to edge storage Pre- and post-alarm video buffering Send video clip Overlay text IR illumination on/off Data streaming Event data Built-in insta ...

  • Axis Communications P3225-LV - page 62

    AXIS P3225-L V Network Camera T echnical Specifications Warranty Axis 3-year warranty and AXIS Extended Warranty option, see www .axis.com/warranty a. This product includes software developed by the OpenSSL Project for use in the OpenSSL T oolkit. (www .openssl.org), and cryptographic software written by Eric Y oung (eay@cryptsoft.com). More infor ...

  • Axis Communications P3225-LV - page 63

    User Manual V er . M2.2 AXIS P3225-LV Network Camera Date: July 20 15 © Axis Communications AB, 20 15 P art No. 149350 7 ...

Fabbricante Axis Communications Categoria Security Camera

I documenti che otteniamo dal fabbricante del dispositivoAxis Communications P3225-LV possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Axis Communications
- manuali per l’uso P3225-LV
- schede prodotto Axis Communications
- opuscoli
- o etichette energetiche Axis Communications P3225-LV
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Axis Communications P3225-LV.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Axis Communications P3225-LV, manuali di manutenzione, brevi manuali o manuali utente Axis Communications P3225-LV. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Axis Communications P3225-LV.

Manuali per l’uso simili

Manuale completo del dispositivo Axis Communications P3225-LV, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Axis Communications P3225-LV dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Axis Communications P3225-LV.

Il manuale per l’uso completo Axis Communications, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Axis Communications P3225-LV - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Axis Communications P3225-LV, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Axis Communications P3225-LV che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Axis Communications P3225-LV - che ci dovrebbe aiutare nei primi passi durante l'uso Axis Communications P3225-LV
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Axis Communications P3225-LV
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Axis Communications P3225-LV in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Axis Communications P3225-LV?

Utilizza il modulo sottostante

Se non hai risolto il problema con Axis Communications P3225-LV con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Axis Communications P3225-LV è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)