ページに移動 of 63
AXIS P3225-L V Network Camera User Manual ...
About this Document This manual is intended for administrators and users of AXIS P3225-LV Network Camera, and is applicable to rmware 5.70 and later . It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems ...
be connected using a shielded network cable (STP) that is properly grounded. Japan こ の 装 置 は 、 ク ラ ス B 情 報 技 術 装 置 で す 。 こ の 装 置 は 、 家 庭 環 境 で使 用 す る こ と を 目 的 と し てい ま す が 、 こ の 装 置 が ラ ジ オ やテ レ ビ ジ ョ ン 受 信 機 に 近 接 ...
AXIS P3225-L V Network Camera Safety Infor mation Safety Infor mation Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury . WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury . CAUTION Indicates a hazardous situation which, if not avoi ...
AXIS P3225-L V Network Camera T able of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hazard Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Other Message Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
AXIS P3225-L V Network Camera T able of Contents Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Reset to Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
AXIS P3225-L V Network Camera Hardware Overview Hardware Overview 1 2 3 4 5 1 Network connector (P oE) 2 SD memory card slot 3 P art number (P/N) & Serial number 4 Control button 5 Status LED indicator Connectors and Buttons For technical specications, see page 60 . Network Connector RJ45 Ethernet connector with P ower over Ethernet (P oE). ...
AXIS P3225-L V Network Camera Hardware Overview • Resetting the product to factory default settings. See page 56 . • Connecting to an AXIS Video Hosting System service. See page 49 . To connect, press and hold the button for about 3 seconds until the Status LED ashes green. • Connecting to AXIS Internet Dynamic DNS Service. See page 49 . T ...
AXIS P3225-L V Network Camera Access the Pr oduct Access the Product To install the Axis product, see the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are • Internet Explorer ® with Windows ® • Safari ® with OS X ® and • Chrome TM or Firefox ® wit ...
AXIS P3225-L V Network Camera Access the Pr oduct For T echnical notes on this and other topics, visit the Axis Support web at www .axis.com/techsup Set the Root P assword To access the Axis product, you must set the password for the default administrator user root . This is done in the Congure Root P assword dialog, which opens when the product ...
AXIS P3225-L V Network Camera Access the Pr oduct Set P ower Line Frequency P ower line frequency is set the rst time the Axis product is accessed and can only be changed from Plain Cong (see page 56 ) or by resetting the product to factory default. Select the power line frequency (50 Hz or 60 Hz) used at the location of the Axis product. Sel ...
AXIS P3225-L V Network Camera Access the Pr oduct 4. From the second drop-down list, select Manual Trigger . 5. Select the desired action and congure the other settings as required. For more information about action rules, see Events on page 37 . To show the manual trigger buttons in the Live View page: 1. Go to Setup > Live View Cong . 2. ...
AXIS P3225-L V Network Camera Access the Pr oduct P an and Tilt bars – Use the arrows to pan and tilt the camera view , or click on a position on the bar to steer the camera view to that position. Zoom bar – Use the arrows to zoom in and out, or click on a position on the bar to zoom to that position. The PTZ controls can be disabled under PTZ ...
AXIS P3225-L V Network Camera Media Streams Media Streams The Axis product provides several video stream formats. Y our requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, and to the list of available stream proles. Other applic ...
AXIS P3225-L V Network Camera Media Streams The AMC Control P anel can be used to congure various video settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control P anel is automatically installed on rst use, after which it can be congured. Open the AMC Control P anel from: • Windows Control P anel ...
AXIS P3225-L V Network Camera Media Streams Note • <ip>= IP addess • The Axis product supports QuickTime 6.5.1 and later . • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this. 16 ...
AXIS P3225-L V Network Camera Set Up the Product Set Up the Product The Axis product can be congured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to all set ...
AXIS P3225-L V Network Camera Video Video It is possible to congure the following video features in your Axis product: • Video stream. See page 18 . • Stream proles. See page 20 . • Camera settings. See page 20 . • View areas. See page 23 . • Overlay image. See page 23 . • Privacy mask. See page 25 . Set Up Video Streams To set up ...
AXIS P3225-L V Network Camera Video • Maximum frame rate . To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a xed amount. Alternatively , the frame rate can be set as Unlimited , which means the Axis product always delivers the highest frame rate possible under the current conditions. • Overlay settings . ...
AXIS P3225-L V Network Camera Video • Medium Zipstream strength . Medium bandwidth reduction. Limited visual quality degradation in not prioritized areas in some scenes • Highest Zipstream strength . High bandwidth reduction. Visible quality degradation in not prioritized areas in many scenes Lowest Zipstream strength is the default setting for ...
AXIS P3225-L V Network Camera Video To change capture mode, follow these steps: 1. Go to Setup > Video > Camera Settings . 2. Select the new capture mode. 3. Click Save . 4. Review and recongure all settings, for example: - View areas - Stream proles - PTZ settings including preset positions and guard tours - Privacy masks - Image overl ...
AXIS P3225-L V Network Camera Video Important Use WDR in combination with automatic exposure control. Other exposure settings could give undesirable results. Exposure Settings Congure the exposure settings to suit the image quality requirements in relation to lighting, frame rate and bandwidth considerations. Exposure value - Use the Exposure va ...
AXIS P3225-L V Network Camera Video Built-in IR Illuminations LEDs WARNING Risk of eye injury . Do not look directly into the IR LED at short distance. Since the light provided from the IR LED is outside of the visible range, it is not possible to see if it is active. Use the camera to check if the IR illumination is active. The IR illumination can ...
AXIS P3225-L V Network Camera Video An overlay text can display the current date and time, or a text string. When using a text string, modiers can be used to display information such as the current bit rate or the current frame rate. For information about available modiers, see File Naming & Date/Time Formats in the online help . It is al ...
AXIS P3225-L V Network Camera Video To select the image to use as overlay: 1. Go to Video > Overlay Image . 2. Select the image to use from the Use overlay image list and click Save . To display the overlay image: 1. Go to Video > Video Stream and select the Image tab . 2. Under Overlay Settings , select Include overlay image at the coordinat ...
AXIS P3225-L V Network Camera Video Important Adding many privacy masks may affect the product’s performance. 26 ...
AXIS P3225-L V Network Camera Configure the Live View Page Configure the Live View Page Y ou can customize the Live View page and alter it to suit your requirements. It is possible to dene the following features of the Live View page. • Stream Prole. See page 20 . • Default Viewer for Browser . See page 27 . • Viewer Settings. See pag ...
AXIS P3225-L V Network Camera Configure the Live View Page • Select Enable recording button to enable recording from the Live View page. This button is available when using the AMC viewer . The recordings are saved to the location specied in the AMC Control P anel. See AXIS Media Control (AMC) on page 14 . User Dened Links To display user- ...
AXIS P3225-L V Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area. For more information on view areas, see View Area on page 23 . Preset P ositions A preset position is a saved view that can be used to quickly steer the camera to a specic posit ...
AXIS P3225-L V Network Camera PTZ (Pan Tilt Zoom) 3. Specify the pause length between runs. 4. Select an available preset position and click Apply . 5. Specify the View Time in seconds or minutes. 6. Specify the View Order or select the Random view order option. 7. Click Save . To modify or remove guard tours, go to PTZ > Guard T our , select th ...
AXIS P3225-L V Network Camera PTZ (Pan Tilt Zoom) 2. Event — The Axis product can be congured to go to a preset position when triggered by an alarm (see Events on page 37 ). The event will immediately be placed rst in the queue except when an administrator is in control. 3. Operator — Same as administrator but with lower priority 4. Guard ...
AXIS P3225-L V Network Camera Detectors Detectors Camera T ampering Camera T ampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, spray-painted or severely defocused. To send an alarm, for example an email, an action rule must be set up. To congure tampering detection: 1. Go to Detectors > Camera Ta ...
AXIS P3225-L V Network Camera Detectors Note • Using the motion detection feature may decrease the product’s overall performance. • The position of the Motion Detection Window is relative to the orientation of the Camera. Changing the orientation of the camera will also change the position of the Motion Detection Window . Set Up Motion Detect ...
AXIS P3225-L V Network Camera Detectors Note • T o trigger on small objects or movements, use several small motion detection windows rather than one large window and select a low object size. • T o avoid triggering on small objects, select a high object size. • While monitoring an area where moving objects are not expected, select a high hist ...
AXIS P3225-L V Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting. For information about available applications, down ...
AXIS P3225-L V Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings . 36 ...
AXIS P3225-L V Network Camera Events Events The Event pages allow you to congure the Axis product to perform actions when different events occur . For example, the product can start a recording or send an email notication when motion is detected. The set of conditions that denes how and when the action is triggered is called an action rule ...
AXIS P3225-L V Network Camera Events - Temperature – Trigger the rule if the temperature falls outside or inside the operating range of the product. This can for example be used to send maintenance notications. • Input Signal - Manual T rigger – Trigger the rule using the Manual Trigger button in the Live View page. See Controls on the Liv ...
AXIS P3225-L V Network Camera Events • Send SNMP T rap – Send an SNMP trap message to the operator . Make sure that SNMP is enabled and congured under System Options > Network > SNMP . • Send Video Clip – Send a video clip to a recipient. • WDR Mode – The WDR Mode can be turned on or off when the action rule is triggered. Add R ...
AXIS P3225-L V Network Camera Events HTTPS Send Images Send Notication Send Video Clip Encrypted le transfer using HyperText T ransfer Protocol Secure (HTTPS). Specify login information for the HTTPS server and validate the server’s certicate. If there is a proxy between the Axis product and the HTTPS server , also specify the proxy sett ...
AXIS P3225-L V Network Camera Events Set Up Recurrences Recurrences are used to trigger action rules repeatedly , for example every 5 minutes or every hour . To set up a recurrence: 1. Go to Events > Recurrences and click Add . 2. Enter a descriptive name and recurrence pattern. 3. Click OK . To use the recurrence in an action rule, rst selec ...
AXIS P3225-L V Network Camera Recordings Recordings The Axis product can be congured to record video continuously or according to an action rule: • To start a continuous recording, see page 43 . • To set up action rules, see page 37 . • To access recordings, see Find Recordings on page 42 . • To play recordings, see Play Recording on pag ...
AXIS P3225-L V Network Camera Recordings To play a recording, follow these steps: 1. Go to Recordings > List . 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the lters. See also Find Recordings on page 42 . 3. Select the recording and click Play . The recording wil ...
AXIS P3225-L V Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. T o switch languages, go to Setup > Languages and rst upload the new language le. Browse and locate the le and click the Upload Language button. Se ...
AXIS P3225-L V Network Camera System Options System Options Security Users User access control is enabled by default and can be congured under System Options > Security > Users . An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may ...
AXIS P3225-L V Network Camera System Options 2. Select an HTTPS certicate from the list of installed certicates. 3. Optionally , click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection P olicy for the different user groups. 5. Click Save to enable the settings. To access the Axis product via the desired ...
AXIS P3225-L V Network Camera System Options A Server/Client certicate can be self-signed or issued by a Certicate Authority (CA). A self-signed certicate offers limited protection and can be used before a CA-issued certicate has been obtained. To install a self-signed certicate: 1. Go to Setup > System Options > Security > ...
AXIS P3225-L V Network Camera System Options IPv4 Address Conguration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP . The IPv4 settings are congured under System Options > Network > TCP/IP > Basic . DHCP (Dynamic Host Conguration Protocol) allows network administ ...
AXIS P3225-L V Network Camera System Options 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar . 6. Open a browser and type http://<IP address> in the Location/Address eld. For other methods of assigning the IP address, see the document Assign an IP Address and Access the Video Stream on Axi ...
AXIS P3225-L V Network Camera System Options NTP Conguration NTP (Network Time Protocol) is used to synchronize the clock times of devices in a network. The NTP settings are congured under System Options > Network > T CP/IP > Advanced . Select Obtain NTP server address via DHCP to use the NTP settings provided by the DHCP server . To ...
AXIS P3225-L V Network Camera System Options Use manually selected NAT router - Select this option to manually select a NA T router and enter the IP address for the router in the eld. If no router is specied, the product automatically searches for NAT routers on your network. If more than one router is found, the default router is selected. A ...
AXIS P3225-L V Network Camera System Options Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message. Note If HTTPS is enabled, SNMP v1 and SNMP v2c shoul ...
AXIS P3225-L V Network Camera System Options Storage SD Card NO NO NO TICE TICE TICE To prevent data corruption, the SD card should be unmounted before removal. Note For SD card recommendations see www .axis.com The Axis product supports microSD/microSDHC/microSDXC cards. The following SD card le systems are supported: • ext4 — recommended d ...
AXIS P3225-L V Network Camera System Options To enable automatic formatting, follow these steps: 1. Open the Axis product’s webpages and go to Setup > System Options > Storage . 2. Click SD Card . 3. Under General Settings , select Autoformat to . 4. Click OK to save settings. An SD card inserted into the product can be manually formatted t ...
AXIS P3225-L V Network Camera System Options Click Restore to reset most settings to the factory default values. The following settings are not affected: • the boot protocol (DHCP or static) • the static IP address • the default router • the subnet mask • the system time • the IEEE 802.1X settings • uploaded applications are kept but ...
AXIS P3225-L V Network Camera System Options Advanced Scripting Scripting allows experienced users to customize and use their own scripts. NO NO NO TICE TICE TICE Improper use may cause unexpected behavior and loss of contact with the Axis product. Axis strongly recommends that you do not use this function unless you understand the consequences. Ax ...
AXIS P3225-L V Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your rst actions when troubleshooting a problem should be to check the current rmware version. The latest version may contain a correction that xes your particular problem. The c ...
AXIS P3225-L V Network Camera Troubleshooting The IP address is being used by another device Disconnect the Axis product from the network. Run the Ping command (in a Command/DOS window , type ping and the IP address of the product): • If you receive: Reply from <IP address>: bytes=32; time=10... this means that the IP address may already be ...
AXIS P3225-L V Network Camera Troubleshooting Installation of additional ActiveX component restricted or prohibited Congure the Axis product to use a Java applet for updating video images in your browser . Go to Setup > Live View Cong and select Java applet under Default viewer . P oor rendering of H.264 images Ensure that your graphics ca ...
AXIS P3225-L V Network Camera T echnical Specifications T echnical Specifications Camera Image sensor Progressive scan RGB CMOS 1/2.8” Lens Varifocal, 3.0–1 0.5 mm, F1.4 Horizontal angle of view 92°–34° V ertical angle of view 50°–20° Remote focus and zoom, P-Iris control, IR corrected Day and night Automatically removable infrared-cu ...
AXIS P3225-L V Network Camera T echnical Specifications Event actions File upload: FTP , SFTP , HTTP , HTTPS, network share and email Notication: email, HTTP , HTTPS, T CP and SNMP trap Video recording to edge storage Pre- and post-alarm video buffering Send video clip Overlay text IR illumination on/off Data streaming Event data Built-in insta ...
AXIS P3225-L V Network Camera T echnical Specifications Warranty Axis 3-year warranty and AXIS Extended Warranty option, see www .axis.com/warranty a. This product includes software developed by the OpenSSL Project for use in the OpenSSL T oolkit. (www .openssl.org), and cryptographic software written by Eric Y oung (eay@cryptsoft.com). More infor ...
User Manual V er . M2.2 AXIS P3225-LV Network Camera Date: July 20 15 © Axis Communications AB, 20 15 P art No. 149350 7 ...
Axis Communications P3225-LVのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- P3225-LVの取扱説明書
- Axis Communicationsの製品カード
- パンフレット
- またはAxis Communications P3225-LVの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Axis Communications P3225-LVの取扱説明書に含まれています。
取扱説明書と呼ばれる文書のグループは、Axis Communications P3225-LVの取り付け説明書、サービスマニュアル、簡易説明書、またはAxis Communications P3225-LVのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Axis Communications P3225-LVの製品を使用するにあたって最も人気のある説明書を閲覧できます。
Axis Communications P3225-LVデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAxis Communications P3225-LVを使用するのを助ける技術的文書のことです。説明書は通常、全てのAxis Communications P3225-LVユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。
Axis Communicationsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。
1. Axis Communications P3225-LVの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAxis Communications P3225-LVの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Axis Communications P3225-LVに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Axis Communications P3225-LVデバイスの基本機能を使うにあたってのヒント。 Axis Communications P3225-LVのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Axis Communications P3225-LVに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAxis Communications P3225-LVのメーカー/サービスへの連絡先に関する情報。
Axis Communications P3225-LVについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもAxis Communications P3225-LVの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAxis Communications P3225-LVで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。