Italiano dropdown-ico

Manuale per l’uso Vermont Casting A052041

24 pagine 1.75 mb
Scarica

Vai alla pagina of 24

Summary
  • Vermont Casting A052041 - page 1

    F O R Y O U R S A F E T Y I f y o u sm e l l g a s: 1 S h u t o g a s to th e a p p l i a n c e . 2 E x t i n g u i sh a n y o p e n  a m e . 3 O p e n l i d . 4 I f o d or c on t i n u e s, i m m e d i a te l y c a l l y o u r g a s su p p l i e r o r  r e d e p a r tm e n t . F O R Y O U R SA F E TY 1 D o n o t st o r e or u se g a so l ...

  • Vermont Casting A052041 - page 2

    T able of Contents Page Number Chapter One - INSTALLATION 4 Necessary Information 4 Choosing a Safe Location 4 Portable L.P. Gas Grills 5 - 7 Important Features of the Series 4000 LP Gas Grill 8 L.P. Gas Dealer Instructions 9 Chapter Two - ASSEMBL Y INSTRUCTIONS 10 Identifying Parts 11 Attach Pillar to Grill Bottom 12 - 13 Assemble Base to Pillar 1 ...

  • Vermont Casting A052041 - page 3

    The gas fuel used by this product is highly flammable and must be used in a responsible and cautious manner . It is your responsibility to assemble, operate, and maintain your gas barbecue grill properly . If these instructions are ignored, there is a possibility of a hazardous fire or explosion which could result in proper- ty damage, physical inj ...

  • Vermont Casting A052041 - page 4

    • The ventilation openings of the cylinder enclosure must be kept free and clear from other debris. 6. Do Not store a spare L.P. gas cylinder under or near this appliance. • Do not store an L.P. cylinder in a build- ing, garage or any other enclosed area. Instead, store the cylinder outdoors in a well ventilated area, away from people and out o ...

  • Vermont Casting A052041 - page 5

    2. The system has a thermal element that will shut off the flow of gas between 240° F and 300° F . 3. The system has a flow-limiting device which when activated, will limit the flow of gas to 10 cubic feet per hour . 4. The pressure regulator and hose assem- bly provided is factory set at an outlet pres- sure of 11 inches water column (.4 lb. per ...

  • Vermont Casting A052041 - page 6

    L.P. GAS CYLINDER SPECIFICATIONS Any L.P. gas-supply cylinder used with this grill must be approximately 12 inches diameter and 18 inches high. The maxi- mum fuel capacity must be 20 pounds of propane. Full-cylinder weight should be approximately 38 pounds (43.7 lbs. nominal water capacity). The L.P. cylinder must have a shut-off valve terminating ...

  • Vermont Casting A052041 - page 7

    8 Rear view of Series A052041 grill with the heat shield, gaskets, collar assembly. HEA T SHIELD, GASKETS AND COLLAR W ARNING! Do not remove the heat shield, gaskets, collar assembly from the grill bottom. Operating this grill without the heat shield, gaskets, collar assembly attached to the grill bottom would result in a hazardous situation which ...

  • Vermont Casting A052041 - page 8

    Filling a Type 1 Cylinder Valve Example A: shows a CGA-510 POL fitting. Example B: shows using a Type 1 POL fitting. When using a cylinder exchange, be sure the exchanged cylinder is a T ype 1 cylinder; a 510 POL cylinder will not fit a T ype 1 regulator . F ILLING AND P URGING T YPE 1 L.P. G AS C YLINDERS DANGER! Purging and filling of L.P. Gas cy ...

  • Vermont Casting A052041 - page 9

    Assembly Instructions Chapter 2 Getting Star ted 1. Please follow the steps in the order that they are presented. 2. Assemble the grill where you plan to use it. 3. Y ou may want to place an old towel or cloth at the assembly site to prevent nuts and bolts from becoming lost. 4. Have a friend help. An assistant can make the assembly easier by holdi ...

  • Vermont Casting A052041 - page 10

    A ssembly Instructions • Identify the G r ill Parts warming rack (1) cooking grid (1) ceramic briquettes ( 1 package ) rock grate (1) left side table (1) right side table (1) base (1) master hardware bag (1) consisting of: (1) "A" bag (1) "B" bag (1) "C" bag (1) "D" bag 11 handle (1) handle standoff (2) gri ...

  • Vermont Casting A052041 - page 11

    HINT: For the first portion of the assembly you will be assembling the grill bottom, pillar and base up- side-down. 1. Position the grill bottom casting upside down so that the heat collar assembly is upward. 2. W orking from the back (open) side of the pillar, set the pillar upside down onto the collar assembly . 3. Locate the holes in the pillar ...

  • Vermont Casting A052041 - page 12

    back hinge strut pillar bottom grill bottom back gas control valve ends fuel supply hose w/ regulator burner venturi tubes collar 13 ...

  • Vermont Casting A052041 - page 13

    1. Lock the pre-assembled casters on base by pushing down on the latch. 2. Set the base upside-down on onto the pillar bottom as shown on the adjacent page, aligning holes in base with holes in pillar . 3. Insert six bolts through the holes in the pillar and base. Thread the locking hex nuts onto bolts. T ighten with a wrench and a flat- head screw ...

  • Vermont Casting A052041 - page 14

    15 ignitor unit base back top pillar black lead wires heat shield bottom casting back ...

  • Vermont Casting A052041 - page 15

    1 Now with the help of an assistant carefully turn the grill assembly right-side-up. 2. IMPORTANT : Inspect beneath the grill bottom to check that the control-valve ends are still inside the burner venturi tubes. The valve ends must always be inside the burner tubes for the grill to safely operate. grill bottom as shown from below back. No tools ne ...

  • Vermont Casting A052041 - page 16

    17 A TTENTION PRODUCT ASSEMBLER: Install the X-brace retainer wire across the back of the pillar for warranty validation. 3. Position the wire ends “A” and “B” firmly into the pillar corners behind the bolt heads and against the base. (See Lower Detail.) 4. Complete the installation by snapping bent ends “C” and “D” into the two hol ...

  • Vermont Casting A052041 - page 17

    Locate these parts: 18 tools needed: 3/8" open-end wrench 7/16" open-end wrench A ssembly Instructions • Install the Side T ables. 1/4-20 x 3/4” bolt ( 8 ) Use hardware bag “C”: 1/4-20 hex nut ( 8 ) right side table assembly ( 1 ) 1. Insert four 3 /4" bolts through holes in the support brackets of the right side table assembl ...

  • Vermont Casting A052041 - page 18

    19 3. Insert four 3 /4" bolts through holes in the support brackets of the left side table assembly . 4. Attach the left side table to the four holes located in the left side of the grill bottom using the locking hex nuts provided. HINT: Preformed hooks included on the right side table assembly may be used to keep cooking utensils (not include ...

  • Vermont Casting A052041 - page 19

    20 A ssembly Instructions • Assemble the G rill Lid tools needed: 7/16" open-end wrench flat-blade screwdriver handle standoff ( 2 ) handle ( 1 ) 1. Position the back of the lid so that the rear holes are in line with the hinge struts on the back of the grill bottom. 2. Gently set the grill lid onto the grill bottom. hairpin ( 2 ) use hardwa ...

  • Vermont Casting A052041 - page 20

    7. Raise the lid to attach the front handle. 8. Attach a handle standoff to the front of the grill lid, as shown. 9. Insert one end of the handle into the hole of the standoff. 10.Place other standoff onto handle and while holding the handle in place assem- ble the opposite standoff to the lid in the same manner . 3. Hold the lid to align the hinge ...

  • Vermont Casting A052041 - page 21

    rock grate ( 1 ) No tools are needed. A ssembly Instructions • Installing the In ternal G rill Parts . 22 ceramic briquettes ( 1 box ) warming rack ( 1 ) 1. Place the single rock grate into the grill bottom. cooking grid ( 1 ) 2. Open the package containing the ceramic briquettes and place them on the rockgrate. Locate these parts: ...

  • Vermont Casting A052041 - page 22

    3. It is important to properly arrange all the ceramic briquettes onto the rock grate to allow for good air flow during use. NOTICE THE SPACING: The proper amount of briquettes are supplied and there is no need to add more. Some space between the briquettes is necessary. 4. Set the porcelain coated cooking grid on the front and back ledges formed i ...

  • Vermont Casting A052041 - page 23

    Replacement parts are available direct from our warehouse. Some components are not available preassembled and may be ordered separately. For convenience, the following parts list is provided along with a representation of the items listed. Charges for replacement parts and shipping may apply . For warranty replacements, proof of own- ership and dat ...

  • Vermont Casting A052041 - page 24

    35 Base Assembly Breakdown of P r eassembled Components Pillar Assembly Bottom/Burner Assembly Side T able Assemblies 1 Base Assembly consisting of: 1 Base SF AH000402 2 Locking Caster AH000303 2 Caster AH000305 quantity description part number 1 Bottom/Burner Assembly consisting of: 1 Cast Iron Burner AZ001505 1 V enturi T ube w/gasket AZ000507 8 ...

Fabbricante Vermont Casting Categoria Gas Grill

I documenti che otteniamo dal fabbricante del dispositivoVermont Casting A052041 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Vermont Casting
- manuali per l’uso A052041
- schede prodotto Vermont Casting
- opuscoli
- o etichette energetiche Vermont Casting A052041
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Vermont Casting A052041.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Vermont Casting A052041, manuali di manutenzione, brevi manuali o manuali utente Vermont Casting A052041. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Vermont Casting A052041.

Manuali per l’uso simili

Manuale completo del dispositivo Vermont Casting A052041, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Vermont Casting A052041 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Vermont Casting A052041.

Il manuale per l’uso completo Vermont Casting, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Vermont Casting A052041 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Vermont Casting A052041, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Vermont Casting A052041 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Vermont Casting A052041 - che ci dovrebbe aiutare nei primi passi durante l'uso Vermont Casting A052041
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Vermont Casting A052041
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Vermont Casting A052041 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Vermont Casting A052041?

Utilizza il modulo sottostante

Se non hai risolto il problema con Vermont Casting A052041 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Vermont Casting A052041 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)