Italiano dropdown-ico

Manuale per l’uso ADTRAN AHDSL2

30 pagine 0.29 mb
Scarica

Vai alla pagina of 30

Summary
  • ADTRAN AHDSL2 - page 1

    61221002L2-5B 1 ADTRAN ® AHDSL2 Asynchronous H2TU-C Line Card for Alcatel Litespan ® Channel Bank Assemblies Using Narrowband Pairs Installation and Maintenance Practice Section 61221002L2-5B Issue 2, August 2003 CLEI Code: SLL5R3DG_ _ CONTENTS 1. General ......................................................................... 1 2. Applications ...

  • ADTRAN AHDSL2 - page 2

    2 61221002L2-5B Table 1 lists and defines the H2TU-C Front Panel LED indicators. Each ADTRAN Litespan H2TU-C line card provides a 1.552 kbps data transport over one unconditioned CSA copper pair. These CSA loops can range up to 12 kft of 24-AWG twisted pair wire. The Litespan H2TU-C can be used in Litespan 2000, Litespan 2012, and Litespan ONU chan ...

  • ADTRAN AHDSL2 - page 3

    61221002L2-5B 3 2. APPLICATIONS The ADTRAN HDSL2 system provides a cost-effective alternative for deploying T1 service over metallic cable pairs. In contrast with traditional T1 service equipment, ADTRAN HDSL2 can be successfully deployed over one unconditioned, nonloaded, bridged-tapped copper pair CSA loop (see Deployment Guidelines , Section 4). ...

  • ADTRAN AHDSL2 - page 4

    4 61221002L2-5B CAUTION Prior to installing or removing the Litespan H2TU-C, observe the following warning: If the Litespan H2TU-C is removed from a line card slot, wait at least 15 seconds before reinsertion. If connected to the MTI craft interface terminal, wait until the message “AID:MJ,UEQ.” appears (where “AID” is the access identifier ...

  • ADTRAN AHDSL2 - page 5

    61221002L2-5B 5 Provisioning Commands Upon initial insertion of the Litespan H2TU-C into the Litespan system, configuration options are downloaded automatically to the line card and take precedence over the ADTRAN default provisioning options. NOTE The provisioning options stored in the shelf controller can be pre-configured by the user through the ...

  • ADTRAN AHDSL2 - page 6

    6 61221002L2-5B 1 L T s d n a m m o C t f a r c e t i L s r e t e m a r a P C - U T 2 H s n o i t p O C - U T 2 H s g n i t t e S e l b a l i a v A g n i d n o p s e r r o C s g n i t t e S t f a r c e t i L e l b a r u g i f n o C - e r P e u l a V L S D H - D EK B P L D I Nk c a b p o o L U I Nd e l b a s i D d e l b a n E O N S E Y S E Y L S D H ...

  • ADTRAN AHDSL2 - page 7

    61221002L2-5B 7 Testing Commands The H2TU-C testing commands are used to initiate and terminate loopbacks and disconnect for testing purposes. Table 8 lists and defines the TL1/Litecraft testing commands. NOTE Before entering loopbacks, the user needs to remove the card from service. This can be done with the RMV-HDSL command. The card can then be ...

  • ADTRAN AHDSL2 - page 8

    8 61221002L2-5B Figure 4. Deployment Guidelines Table 9 lists the ADTRAN Litespan H2TU-C and H2TU-R factors needed to calculate channel bank power using Worksheet PW-1. The Table 9 power factors are derived from the power parameters listed in Table 10 . 4. DEPLOYMENT GUIDELINES The ADTRAN HDSL2 system is designed to provide DS1-based services over ...

  • ADTRAN AHDSL2 - page 9

    61221002L2-5B 9 Loop loss per kft for other wire is summarized in Table 11 . Cable Gauge 26 26 24 24 22 22 19 19 Cable Type PIC Pulp PIC Pulp PIC Pulp PIC Pulp Temperature ( ° F) 68 ° 90 ° 120 ° 3.902 4.051 4.253 4.030 4.179 4.381 2.863 2.957 3.083 3.159 3.257 3.391 2.198 2.255 2.333 2.483 2.450 2.629 1.551 1.587 1.634 1.817 1.856 1.909 Table 1 ...

  • ADTRAN AHDSL2 - page 10

    10 61221002L2-5B Table 13. Troubleshooting Guide Condition At power up, all front panel indicators are OFF The STAT LED remains RED. The STAT LED is OFF, but the HLOS LED remains RED . The STAT LED is OFF, but the RLOS LED remains RED. Solution 1. Verify that the channel bank or ONU BPS power LEDs are on. 2. Make sure that the unit is fully and cor ...

  • ADTRAN AHDSL2 - page 11

    61221002L2-5B 11 Table 14. ADTRAN H2TU-C Specifications Loop Interface Modulation Type ............................................... 16 TC PAM Mode .................................................................. Full duplex, partially overlapped echo canceling Number of Pairs ................................................ One Line Rate ..... ...

  • ADTRAN AHDSL2 - page 12

    12 61221002L2-5B This page is intentionally blank. ...

  • ADTRAN AHDSL2 - page 13

    61221002L2-5B A-1 HDSL MAINTENANCE MODES This appendix describes operation of the HDSL2 system with regard to detection of in-band and ESF facility data link loopback codes. Upon deactivation of a loopback, the HDSL2 system will synchronize automatically. Loopback Process Description In general, the loopback process for the HDSL2 system elements is ...

  • ADTRAN AHDSL2 - page 14

    A-2 61221002L2-5B Table A-1. In-Band Addressable Loopback Codes n o i t c n u Fe d o Ce s n o p s e R 3 n i 1 1 0 0 1. g n i h t y r e v e n w o d p o o L 6 n i 1 1 0 0 0 0 0 1 e r o f e b d e m r a e b t s u m ; k r o w t e n e h t d r a w o t R - U T 2 H e h t t a k c a b p o o L . d e t a i t i n i 7 n i 40 0 0 1 1 1 1 . C - U T 2 H e h t n i k ...

  • ADTRAN AHDSL2 - page 15

    61221002L2-5B A-3 n o i t c n u Fe d o Ce s n o p s e R n w o d p o o L 3 , 1 3 9 3 9 1 0 0 1 1 1 0 0 1 0 0 1 1 1 0 0 k c a b p o o l n i y l t n e r r u c s t i n u l l a , r e m o t s u c r o k r o w t e n e h t m o r f t n e s n e h W a e k i l e v a h e b o t r e d r o n I . m r a s i d t o n l l i w s t i n u d e m r A . n w o d p o o l l l i ...

  • ADTRAN AHDSL2 - page 16

    A-4 61221002L2-5B This page is intentionally blank. ...

  • ADTRAN AHDSL2 - page 17

    61221002L2-5B B-1 Appendix B TL1 H2TU-C T utorial GENERAL This appendix is intended to highlight the necessary menus/commands needed to provision the ADTRAN H2TU-C card. A more detailed explanation of shelf specific items may be found in the Alcatel TL1 Reference Practice, OSP-363-205-502. Logging into the TL1 command screens is accomplished by ent ...

  • ADTRAN AHDSL2 - page 18

    B-2 61221002L2-5B MAINTENANCE MENU AND ASSOCIATED SUB-MENUS From the Main Menu, enter “2” to display the Maintenance Menu as shown below. Maintenance Menu 1. ADSL Maintenance Menu 2. ATM Maintenance Menu 3. EC1 Maintenance Menu 4. Equipment Maintenance Menu 5. External Controls Menu 6. HDSL Maintenance Menu ← ← ← ← ← Item of interest ...

  • ADTRAN AHDSL2 - page 19

    61221002L2-5B B-3 HDSL MAINTENANCE MENU From the Maintenance Menu, enter “6” to display the HDSL Maintenance Menu as shown below. HDSL Maintenance Menu 1. ALW-MSG-HDSL 2. INH-MSG-HDSL 3. RMV-HDSL 4. RST-HDSL 5. RTRV-ALM-HDSL ← ← ← ← ← Retrieve existing HDSL alarms for the H2TU-C 6. RTRV-ATTR-HDSL 7. RTRV-COND-HDSL 8. SET-ATTR-HDSL B. ...

  • ADTRAN AHDSL2 - page 20

    B-4 61221002L2-5B T1 MAINTENANCE MENU From the Maintenance Menu, enter “20” to display the T1 Maintenance Menu as shown below. T1 Maintenance Menu 1. ALW-MSG-T1 2. ALW-SW-T1 3. CONN-JACK-T1 4. DISC-JACK-T1 5. INIT-REG-T1 ← ← ← ← ← Clears the T1 PM data for the H2TU-C 6. INH-MSG-T1 7. INH-SW-T1 8. OPR-PROTNSW-T1 9. RLS-PROTNSW-T1 10. R ...

  • ADTRAN AHDSL2 - page 21

    61221002L2-5B B-5 PROVISIONING MENU From the Main Menu, enter “3” to display the Provisioning Menu as shown below. Provisioning Menu 1. ADSL Provisioning Menu 2. Cross-Connection Menu ← ← ← ← ← Item of interest for the H2TU-C 3. EC1 Provisioning Menu 4. Equipment Provisioning Menu 5. Ethernet Provisioning Menu 6. HDSL Provisioning Men ...

  • ADTRAN AHDSL2 - page 22

    B-6 61221002L2-5B CROSS-CONNECTION MENU From the Provisioning Menu, enter “2” to display the Cross-Connection Menu as shown below. Cross-Connection Menu 1. DLT-CRS-STS1 2. DLT-CRS-T0 3. DLT-CRS-T1 ← ← ← ← ← Delete an existing cross-connect 4. DLT-CRS-T3 5. DLT-CRS-VC 6. DLT-CRS-VP 7. ED-CRS-STS1 8. ED-CRS-T0 9. ED-CRS-T3 10. ENT-CRS-S ...

  • ADTRAN AHDSL2 - page 23

    61221002L2-5B B-7 ENT-CRS-T1 Command Input Format The choice to enter cross-connects may be accomplished either by selecting “12” from the Cross-Connection Menu or by entering the command directly as shown in the example below where a cross-connect is initiated between slot 1 and slot 21. <ENT-CRS-T1 FROM[]= RT-1-1 TO[]= RT-1-21. or <ENT- ...

  • ADTRAN AHDSL2 - page 24

    B-8 61221002L2-5B HDSL PROVISIONING MENU From the Provisioning Menu, enter “6” to display the HDSL Provisioning Menu as shown below. HDSL Provisioning Menu 1. DLT-HDSL 2. ED-HDSL ← ← ← ← ← Edit HDSL provisioning parameters for the H2TU-C 3. ENT-HDSL 4. RTRV-HDSL 5. DLT-GOS-HDSL 6. ED-GOS-HDSL ← ← ← ← ← Edit the HDSL Grade of ...

  • ADTRAN AHDSL2 - page 25

    61221002L2-5B B-9 <ED-HDSL LPBKACTR[]={0000000000000000 | 0000000000000001}; or <ED-HDSL::RT-1-21:::: LPBKACTR ={0000000000000000 | 0000000000000001}; <ED-HDSL LPBKDEACTCDE[]={0000000000000000 | 0000000000000001 | 0000000000000010}; or <ED-HDSL::RT-1-21:::: LPBKDEACTCDE ={0000000000000000 | 0000000000000001 | 0000000000000010}; <ED-H ...

  • ADTRAN AHDSL2 - page 26

    B-10 61221002L2-5B Grade of Service tables allow the user to set performance monitoring threshold levels for various alarms/event conditions. There are 15 GOS tables available for each type of service (in our case T1 and HDSL). Example: The HDSL GOS1 may contain a loop attenuation threshold setting of 30 (dB) while HDSL GOS2 contains a loop attenua ...

  • ADTRAN AHDSL2 - page 27

    61221002L2-5B B-11 <ED-T1 FMT[]={ESF | SF | UNFR | AUTO}; or <ED-T1::RT-1-21::::FMT={ESF | SF | UNFR | AUTO}; <ED-T1 LINECDE[]= {AMI | B8ZS}; or <ED-T1::RT-1-21::::LINECDE={AMI | B8ZS}; TESTING MENU From the Main Menu, enter “4” to display the Testing Menu as shown below. Testing Menu 1. OPR-LPBK-HDSL ← ← ← ← ← Enable a lo ...

  • ADTRAN AHDSL2 - page 28

    B-12 61221002L2-5B NOTE Prior to entering any loopback command, the line card must be removed from service. Remove card from service = RMV-HDSL; H2TU-C Network Loopback Loop up command = OPR-LPBK-HDSL::RT-1-21-C:::NEND; Loop down command = RLS-LPBK-HDSL::RT-1-21-C:::NEND; H2TU-C Customer Loopback Loop up command = OPR-LPBK-HDSL::RT-1-21-C:::FEND; L ...

  • ADTRAN AHDSL2 - page 29

    61221002L2-5B C-1 This appendix describes the testing functionality available for the ADTRAN H2TU-C card via the MTAU unit. For a complete description of the MTAU unit refer to Alcatel document Common Equipment Unit Descriptions , OSP 363-405-250. NOTE The functionality of the SPLIT and MON features detailed in this document supercedes that shown i ...

  • ADTRAN AHDSL2 - page 30

    C-2 61221002L2-5B Figure C-2 . MON Mode HDSL2 T ransceiver AHDSL2 T est LIU Tip A-3 HDSL2 Loop Ring1 A-4 T AE, RAE EQPT jacks on the MT A U TBE, RBE Alcatel Network Equip MON Mode Used to test tow ard the remote customer equipment REMOVAL OF MTAU TEST ACCESS DISC-JACK-T1 The Disconnect T1 Jack command disconnects a T1 or HDSL facility from the meta ...

Fabbricante ADTRAN Categoria Network Card

I documenti che otteniamo dal fabbricante del dispositivoADTRAN AHDSL2 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici ADTRAN
- manuali per l’uso AHDSL2
- schede prodotto ADTRAN
- opuscoli
- o etichette energetiche ADTRAN AHDSL2
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso ADTRAN AHDSL2.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione ADTRAN AHDSL2, manuali di manutenzione, brevi manuali o manuali utente ADTRAN AHDSL2. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto ADTRAN AHDSL2.

Manuali per l’uso simili

Manuale completo del dispositivo ADTRAN AHDSL2, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare ADTRAN AHDSL2 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti ADTRAN AHDSL2.

Il manuale per l’uso completo ADTRAN, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale ADTRAN AHDSL2 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice ADTRAN AHDSL2, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per ADTRAN AHDSL2 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo ADTRAN AHDSL2 - che ci dovrebbe aiutare nei primi passi durante l'uso ADTRAN AHDSL2
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del ADTRAN AHDSL2
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio ADTRAN AHDSL2 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su ADTRAN AHDSL2?

Utilizza il modulo sottostante

Se non hai risolto il problema con ADTRAN AHDSL2 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con ADTRAN AHDSL2 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)