Italiano dropdown-ico

Manuale per l’uso Cisco Systems 17053

27 pagine 0.06 mb
Scarica

Vai alla pagina of 27

Summary
  • Cisco Systems 17053 - page 1

    Troubleshooting Cisco Catalyst Switches to NIC Compatibility Issues Document ID: 17053 Introduction Prerequisites Requirements Components Used Conventions Background Information Purpose Why Do Autonegotiation and Compatibility Issues Exist? General Troubleshooting for 10/100/1000 Mbps NICs Autonegotiation Valid Configuration Table EtherChannel and ...

  • Cisco Systems 17053 - page 2

    Components Used This document is not restricted to specific software and hardware versions. Conventions Refer to Cisco Technical Tips Conventions for more information on document conventions. Background Information Purpose This document discusses how to troubleshoot these issues: Autonegotiation • Physical Connectivity • Port Errors (Data Link ...

  • Cisco Systems 17053 - page 3

    performance−related issues. The most common problems with NIC issues deal with speed and duplex configuration. Table 1 summarizes all possible settings of speed and duplex for FastEthernet NICs and switch ports. Note: This section is only applicable for 10/100/1000 Mbps (1000BASE−T) NICs, and not 1000BASE−X NICs. Table 1Autonegotiation Val ...

  • Cisco Systems 17053 - page 4

    100 Mbps, Full−duplex 100 Mbps, Full−duplex 100 Mbps, Half−duplex Duplex Mismatch 1 AUTO 100 Mbps, Full−duplex 100 Mbps, Half−duplex 100 Mbps, Full−duplex Duplex Mismatch 1 100 Mbps, Full−duplex 100 Mbps, Full−duplex 100 Mbps, Full−duplex 100 Mbps, Full−duplex Correct Manual Configuration 2 100 Mbps, Half−duplex AUTO 100 Mbps, ...

  • Cisco Systems 17053 - page 5

    2 Some third−party NIC cards can fall back to half−duplex operation mode, even though both the switchport and NIC configuration are manually configured for 100 Mbps, full−duplex. This is because NIC autonegotiation link detection still operates when the NIC is manually configured. This causes duplex inconsistency between the switchport and th ...

  • Cisco Systems 17053 - page 6

    Example for Cisco IOS Software on the Switch − Catalyst 2900XL, 3500XL, 2948G−L3, and 6000 that Run Cisco IOS Software show interfaces type Switch# show interfaces fastethernet 0/1 FastEthernet0/1 is down, line protocol is down • States other than connected and line protocol is up indicate a physical connectivity issue. Complete these steps i ...

  • Cisco Systems 17053 - page 7

    This is an example: %PAGP−5−PORTFROMSTP:Port 3/3 left bridge port 3/3 %PAGP−5−PORTTOSTP:Port 3/3 joined bridge port 3/3 For Cisco IOS Software−based switches, these messages appear for link up/down situations: %LINK−3−UPDOWN: Interface interface , changed state to up %LINK−3−UPDOWN: Interface interface , changed state to down This ...

  • Cisco Systems 17053 - page 8

    collisions are normal. Generally, a one percent ratio of errors to total traffic is acceptable for half−duplex connections. If the ratio of errors to input packets is greater than two or three percent, performance degradation can be noticed. In half−duplex environments, it is possible for both the switch and the connected device to sense the wi ...

  • Cisco Systems 17053 - page 9

    64−byte transmit time occurs. They are only detected during transmissions of packets longer than 64 bytes. Its detection is exactly the same as it is for a normal collision; it just happens later than it does for a normal collision. Excessive Collisions Excessive collisions are the number of frames that are dropped after 16 attempts to send the p ...

  • Cisco Systems 17053 - page 10

    Multiple Collisions This is an indication of a half−duplex configuration. Late Collisions This is an indication of faulty hardware (NIC, cable, or switch port) or a duplex mismatch. Excessive Collisions This is an indication of overutilization of the switch port at half−duplex or duplex mismatch. Carrier Sense This is an indication of faulty ha ...

  • Cisco Systems 17053 - page 11

    2 In−Discard and Lrn−Discard do not exist on all Catalyst platforms. Table 5Possible Causes for Incrementing CatOS Counters Counter Possible Cause Delay Exced Severe problem with the switch. Create a service request with Cisco Technical Support. MTU−Exced Verify ISL and dot1q configurations. Verify another switch or router does not inject ...

  • Cisco Systems 17053 - page 12

    Teaming of Network Interface Cards Teaming of Network Interface Cards, or NIC Teaming, can cause instability in the networks. Such setups can introduce disruptions to the Spanning tree and can make it undergo frequent recomputations. If intermittent loss of connectivity to NIC teamed servers occurs for devices or hosts in the same VLAN, try to disa ...

  • Cisco Systems 17053 - page 13

    Cisco Catalyst Switch Compatibility and Operation−Specific Issues These sections deal with specific Cisco Catalyst switch issues that can affect performance, compatibility, and interoperation of certain NICs. Catalyst 8510 and 8540 CSR In the campus switch router (CSR) Cisco IOS Software Release 12.0(5)W5(13), autonegotiation for speed and duplex ...

  • Cisco Systems 17053 - page 14

    after an autonegotiation failure. For detailed information on Cisco bug IDs, refer to the Bug Toolkit ( registered customers only ) . Refer to Cisco Catalyst 6500 Series Switches Release Notes for more Catalyst 6000 and 6500 documented bug fixes. Catalyst 5000 and 5500 Switches This table lists several known issues found on the Catalyst 5000 and 55 ...

  • Cisco Systems 17053 - page 15

    WS−X5225R) can result in speed or duplex mismatches under certain conditions. The problem typically occurs after the module is reset or the switch port is disabled and reenabled. The workaround is to disconnect and reconnect the cable that connects the workstation to the switch port. CSCdk32984 ( registered customers only ) 4.2(2) The 48−port, ...

  • Cisco Systems 17053 - page 16

    day to once a month. This issue can reoccur even after the switch is power cycled. The purpose of this Cisco bug ID is to combine several software reworks, fixes that resolve and reduce the loss of connectivity issues, and additional troubleshooting checks in software. CSCdr37645 ( registered customers only ) 4.5(8), 5.5(2), 6.1(1) An invalid packe ...

  • Cisco Systems 17053 - page 17

    CSCds89148 ( registered customers only ) 5.5.6, 6.2.1 Xmit−Err counter increments on unconnected ports for unexplained reasons. The bug also resolves an issue of high−CPU utilization conditions that can be caused by unconnected ports that are configured as host ports. For detailed information on Cisco bug IDs, refer to the Bug Toolkit ( registe ...

  • Cisco Systems 17053 - page 18

    For detailed information on Cisco bug IDs, refer to the Bug Toolkit ( registered customers only ) . NIC Compatibility and Operation Issues Disclaimer : Use this table as a guide in order to troubleshoot NIC issues. Consult the NIC vendor for verification and proper resolution of the issue. Table 11 NIC Model/Manufacture Symptom Description Resoluti ...

  • Cisco Systems 17053 - page 19

    AsantéFast 10/100 PCI Adapter Slow login or fails to log in to server.  See technical document TID1084 at Asanté support website. AsantéFast 10/100 PCI Adapter Numerous CRC and FCS errors reported on switch when connected to Power Macintosh 9500.  See technical document TID1109 at Asanté support website. AsantéFast 10/100 PCI Adapter Slo ...

  • Cisco Systems 17053 - page 20

    traffic. 3Com 3C905/3C905B Intermittent DHCP issues. Despite the proper configuration of Catalyst switch ports, workstations still experience some intermittent DHCP issues. Upgrade to driver version 4.01b or later, which resolves DHCP issues. 3Com 3C905/3C905B Unable to log in to Novell Internetwork Packet Exchange (IPX) network. Despite the proper ...

  • Cisco Systems 17053 - page 21

    1.0.33921641.2241835. 3Com 3C985/3C985B Novell 5.0 issues Refer to 3Com technical support reference 1.0.16744826.2027011. 3Com 3C985/3C985B Clients are unable to log in or browse server, but pings work correctly.  Refer to 3Com technical support reference 2.0.4428387.2305072. 3Com 3C985/3C985B Packets larger than Ethernet MTU (1518 bytes) are ge ...

  • Cisco Systems 17053 - page 22

    fails. The motherboards were manufactured with an Intel Chipset that are incompatible with Cisco switches and Netgear hubs. IBM 10/100 EtherJet CardBus Adapter Extremely slow performance when operating at 10 Mbps. Certain 10/100 switches implement automatic correction for polarity−reversed cables that are not completely compatible with the same c ...

  • Cisco Systems 17053 - page 23

    can see poor network connections or excessive numbers of dropped packets. The interoperability issue arises when a module with a ten bit interface (TBI) transmits an odd byte packet to a receiver with a Gigabit media−independent interface (GMII). Carrier Extension is detailed in subsection 35.2.3.5 in the IEEE 802.3 specification. Carrier Extensi ...

  • Cisco Systems 17053 - page 24

    type keyword can be set to Auto Detect or 10BASE−T/100BaseTX. The related port on the attached hub or switch must also be set to 10Mbps, full−duplex. Xircom RealPort2 CardBus Ethernet 10/100 Adapter (R2BE/RBE/CBE) Models Extremely slow performance when operating at 10 Mbps. Certain 10/100 switches implement automatic correction for polarity−r ...

  • Cisco Systems 17053 - page 25

    manufacturer patches and utility software are installed. Xircom XE2000 PCMCIA NIC Does not autonegotiate to 100 Mbps, full−duplex. NIC only autonegotiates to 100 Mbps, half−duplex. Known limitation of XE2000 NIC. Refer to the XE2000 release notes. Appendix A: Information to Gather Before Creating a Service Request If the troubleshooting procedu ...

  • Cisco Systems 17053 - page 26

    0.14 Loopback 1 = loopback mode switched on 0 = loopback mode switched off 0.13 Rate Selection (least−significant bit [LSB]) 0.6 0.13 1 1 reserved 1 0 1000 Mbps 0 1 100 Mbps 0 0 10 Mbps 0.12 Autonegotiation Enable 1 = autonegotiaton enabled 0 = autonegotiation disabled 0.11 Power Down 1 = power down 0 = normal down 0.10 Isolated 1 = PHY electrica ...

  • Cisco Systems 17053 - page 27

    partner and defaults to half−duplex. As described in Appendix B: Understanding How Autonegotiation Works, pulses within the FLP are used to derive code words that exchange link partner capabilities. The first code word exchanged is referred to as the base page. It informs each link partner of the message type, IEEE 802.3 or IEEE 802.9a, and a tec ...

Fabbricante Cisco Systems Categoria Switch

I documenti che otteniamo dal fabbricante del dispositivoCisco Systems 17053 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cisco Systems
- manuali per l’uso 17053
- schede prodotto Cisco Systems
- opuscoli
- o etichette energetiche Cisco Systems 17053
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cisco Systems 17053.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cisco Systems 17053, manuali di manutenzione, brevi manuali o manuali utente Cisco Systems 17053. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cisco Systems 17053.

Manuali per l’uso simili

Manuale completo del dispositivo Cisco Systems 17053, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cisco Systems 17053 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cisco Systems 17053.

Il manuale per l’uso completo Cisco Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cisco Systems 17053 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cisco Systems 17053, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cisco Systems 17053 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cisco Systems 17053 - che ci dovrebbe aiutare nei primi passi durante l'uso Cisco Systems 17053
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cisco Systems 17053
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cisco Systems 17053 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cisco Systems 17053?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cisco Systems 17053 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cisco Systems 17053 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)