Italiano dropdown-ico

Manuale per l’uso Sears 26462_0

22 pagine 1.93 mb
Scarica

Vai alla pagina of 22

Summary
  • Sears 26462_0 - page 1

    SF./_S OWNERS MANUAL Model No. 26462_0 CRAFTSMAN o PROFESSIONAL MID-SIZED ROUTER TABLE WARNING: Before operating product, read this manual and follow all its Safety and Operating Instructions. Sears, Roebuck and Co., Hoffman Estates IL 60179 USA 26462 12/00 Printed in U.S.A. 4 9LCN- 84 ...

  • Sears 26462_0 - page 2

    General Safety Instructions for Power Tools ................................................ 3 Additional Safety Instructions for Router Tables ......................................... 4 Introduction ........................................ . ......................................................... '...5 Optional Router Table Accessories ... ...

  • Sears 26462_0 - page 3

    SAFETY GUIDELINES- DEFINITIONS This manual contains informa- tion that is important for you to know and understand. This information relates to protect- ing YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you rec- ognize this information, we use the symbols to the right. Please read the manual and pay attention to these sections. IADANGER l ...

  • Sears 26462_0 - page 4

    18. Use recommended accessories Consult the owner's manual for recommended accessories and follow the instructions. The use of improper accessories may cause hazards. 19. Never stand on tool Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. DO NOT store materials above or near the tool making it ...

  • Sears 26462_0 - page 5

    switch box when turning the router ONor OFF. DO NOT touch anything but the switch box when doing this. NEVER reach under the router table for anyrea- son when therouter is running, except to turn it OFF. I A I 24.[ WARNING J Before making any cut, make sure the router is turned OFF, the router bit is not rotating, and the power cord is unplugged fr ...

  • Sears 26462_0 - page 6

    TOOLS REQUIRED • Phillips screwdriver. ° Small or medium sized adjustable wrench (or a set of nutdrivers). ° Electrical with 5/32" drill bit. • Hammer ROUTER TABLE 1. Position the router table top (Part No. 29LCN-981) as shown in Figure 1, with the bottom of the table top facing toward you. 2. Position the table legs (Part No. 29LCN-1283 ...

  • Sears 26462_0 - page 7

    FIGURE 5 FIGURE 7 Front of--. Router Table #10-32 Hex "Keps"_ Nut, (Typical)_ -_,- _ / Router _ _ ,_/ / Table _,_ _ --///_ / Leg Switch_ "_ #10-32 518" Long Truss Head Machin Screw, (Typical) MOUNTING ROUTER TO THE ROUTER TABLE I WARNINGI ALWAYS UNPLUG ROUTER BEFORE MOUNTING. Craftsman Routers with Three-Hole and 6" Diame ...

  • Sears 26462_0 - page 8

    Other Brands of Routers It will be necessary for you to purchase a Craftsman Professional Router Adapter Plate, #25333, from your local Sears Retail Outlet, or through the Sears Catalogue. Routers with a total overall height of 13 inches or less, and a base diameter of 7 inches or less can be accommodated. m I NOTE I Because of vibration that occur ...

  • Sears 26462_0 - page 9

    4. Repeat steps 1 through 3 for the other side of the fence. 5. Make sure the adjustable jointing fence is inside the router table fence as far as it will go and that the clamping knob has been securely tightened. FIGURE 14 Fence Clamping Knob 114-20 x 1-3/4",ong II Round Head _./|l Square IL Neck Bolt / 9/32" LD. x 3/4" O.D. L_ / x ...

  • Sears 26462_0 - page 10

    I _'WARNINGI The vibrations from operating the router can, from time to time, cause the hex nut and the clamp plate to become loose on the clamp rod. PERIODICALLY CHECK THESE FASTENERS AND ALL FASTENERS to ensure that they are tight and secure. PUSH BLOCK ASSEMBLY TO THE ROUTER TABLE FENCE 1. Position the clamp plate relative to the push block ...

  • Sears 26462_0 - page 11

    surface before use. Failure to do so could cause the router table to tip over or slide, resulting in property damage and/or serious personal injury. 1. Set the router table on a workbench or other stable and sturdy surface. 2, While holding the router table in place, spot the loca- tion of the two mounting holes in each of the legs onto the workben ...

  • Sears 26462_0 - page 12

    GENERAL The power switch box is designed to be used with most Craftsman router tables. It provides the conven- ience of an "ON-OFF" switch box at the front of the table, thus eliminating the need to reach underneath the table to turn the router "ON" and "OFF". The power switch box also provides an optional simultaneous ...

  • Sears 26462_0 - page 13

    The switch box incorporates two positive features to prevent inadvertent switching on of the router and the unauthorized, and possibly hazardous, use by others. Inadvertent switching on of the router is prevented by the clear plastic switch box cover. The cover must be raised and the switch box manually toggled to the "ON" position to sta ...

  • Sears 26462_0 - page 14

    USING THE ROUTER TABLE The fence on your router table is provided as a guide to hold the work piece for accuracy in routing. I_I_WARNING] BEFORE each and every use, make sure the router table is SECURE on a work- bench and DOES NOT MOVE. ALIGNMENT OF UNITIZED FENCE TO MITER BAR SLOT 1. Line up the front of the fence with the "0" marks on ...

  • Sears 26462_0 - page 15

    section ADJUSTING DEPTH AND HEIGHT OFTHE CUT. Tightly secure the fence assembly and the router as described before. (MAKE SURE ROUTER IS UNPLUGGED WHEN MAKING ADJUSTMENTS.) 3. LOWER THE OVERHEAD GUARD to the operating position. (Overhead guard shown raised for reasons of clarity.) 4. Check you adjustments by turning the router "ON" using ...

  • Sears 26462_0 - page 16

    FIGURE 29 Fence Clamping Knob Fence Clamping Knob Fence.,. Clamping_ Knob', _crap Nood Adjustabk Jointing Fence flush with Router Table ' Piloted Router Bit Fence Overhead guard shown raised for reasons of clarity. FIGURE 30 Router Table Fence Work Piece Pilot Bearing rides against Router Pilot Bearing Piloted Router Bit "Work Piece ...

  • Sears 26462_0 - page 17

    Cutting Tenons 1. Make certain that the adjustable fence is locked in position with its face flush with the front face of the fence. 2. Mount the push block assembly on the fence, as described in the section PUSH BLOCK ASSEMBLY TO THE ROUTER TABLE UNITIZED FENCE. 3. Install the proper table top insert into the table top hole. 4. Mark line "A&q ...

  • Sears 26462_0 - page 18

    I I When cutting tenons, always clamp I NOTE the work piece with the end to be cut resting flat on the table top. This will minimize steps in the finished tenon surface due to variations in the table top flatness. See FIGURE 36 k Piece ////_ _" Previous cuts Figure 37. l I NOTE I Always cut full depth on all four J sides of tenon in one pass a ...

  • Sears 26462_0 - page 19

    PARTS LIST FOR CRAFTSMAN PROFESSIONAL MID-SIZED ROUTER TABLE MODEL NO. 26462 @ @ @ @ @@@ @ @ @@ @@@ @ @@ KEY! 1 2 '3 4 5 6 7 .-. 8 9 10 "-11 - "12 "13 _14 15 _16 17 _'- 18 _19 -"'- 20 PART NO. 29LCN-981 29LCN-1283 29LCN-996-1 29LCN-996-2 29LCN-996-3 29LCN-1255 29LCN-1019 29LCN-1018 29LCN-994 29LCN-758 29LCN-99 ...

  • Sears 26462_0 - page 20

    TABLE ASSEMBLY FENCE ASSEMBLY U MISCELLANEOUS PARTS 2O ...

  • Sears 26462_0 - page 21

    MITER BAR ASSEMBLY @ PUSH BLOCK ASSEMBLY SWITCH ASSEMBLY 21 ...

  • Sears 26462_0 - page 22

    When corresponding, always give the following information as shown in the list: Printed in U.S.A. 12/00 49LCN-84 1. The PART NUMBER 2. The PART DESCRIPTION 3. The MODEL NUMBER: 26462 4. The ITEM NAME - PROFESSIONAL MID-SIZED ROUTER TABLE ...

Fabbricante Sears Categoria Router

I documenti che otteniamo dal fabbricante del dispositivoSears 26462_0 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Sears
- manuali per l’uso 26462_0
- schede prodotto Sears
- opuscoli
- o etichette energetiche Sears 26462_0
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Sears 26462_0.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Sears 26462_0, manuali di manutenzione, brevi manuali o manuali utente Sears 26462_0. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Sears 26462_0.

Manuali per l’uso simili

Manuale completo del dispositivo Sears 26462_0, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Sears 26462_0 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Sears 26462_0.

Il manuale per l’uso completo Sears, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Sears 26462_0 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Sears 26462_0, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Sears 26462_0 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Sears 26462_0 - che ci dovrebbe aiutare nei primi passi durante l'uso Sears 26462_0
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Sears 26462_0
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Sears 26462_0 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Sears 26462_0?

Utilizza il modulo sottostante

Se non hai risolto il problema con Sears 26462_0 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Sears 26462_0 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)