Italiano dropdown-ico

Manuale per l’uso Quantum 6-01376-07

32 pagine 0.27 mb
Scarica

Vai alla pagina of 32

Summary
  • Quantum 6-01376-07 - page 1

    6-01376-07 StorNext 3.1 ® StorNext File System T uning Guide File System T uning Guide File System T uning Guide ...

  • Quantum 6-01376-07 - page 2

    StorNext 3.1 File System Tuning Guide, 6-01376-07 , Ver. A, Rel. 3.1 , October 2007, Made in USA. Quantum Corporation provides this publ ication “as is” without warranty of an y kind, either express or implied, including but not limited to the implied warranties of merc hantability or fitness for a particular purpose. Quantum Corporation may re ...

  • Quantum 6-01376-07 - page 3

    StorNext File System Tuning Gu ide i Content s Chapter 1 StorNext File System Tuning 1 The Underlying Storage System ............. ... ......... .............. .............. .............. ... 1 RAID Cache Configuration .............. .............. .............. ............... .............. 2 RAID Write-Back Caching .... .............. ....... ...

  • Quantum 6-01376-07 - page 4

    StorNext File System Tuning Guide 1 0 S torNext File System T uning The StorNext File System (SNFS) pr ovides extremely high performance for widely varying scenarios. Many factors determine the level of performance you will realiz e. In particular, the performance characteristics of the underlying st orage system are the most critical factors. Howe ...

  • Quantum 6-01376-07 - page 5

    StorNext File System T uning The Underlying Storage System StorNext File System Tuning Guide 2 RAID Cache Configuration 0 The single most i mportant RAID tuning component is the cache configuration. This is particular ly t rue for small I/O operat ions. Contemporary RAID systems such as the EMC CX series and the various Engenio systems provide exce ...

  • Quantum 6-01376-07 - page 6

    StorNext File System T uning The Underlying Storage System StorNext File System Tuning Guide 3 File System Mana ger (FSM) stati stics reports in the cvlog file. For example, here is a message line from the cvlog file: PIO HiPriWr SUMMAR Y SnmsMetaDisk0 sysavg/350 sysmin/333 sysmax/367 This statistics message rep orts av erage, minimum, and maximum ...

  • Quantum 6-01376-07 - page 7

    StorNext File System T uning The Underlying Storage System StorNext File System Tuning Guide 4 unusual cases, it severely degrades typical sce narios. Therefore, it is unsuitable for most environments. RAID Level, Segment Size, and S tripe Size 0 Configuration settings such as RAID level, segment si ze, and stripe size are very important and cannot ...

  • Quantum 6-01376-07 - page 8

    StorNext File System T uning File Size Mix and Application I/O Characteristics StorNext File System Tuning Guide 5 File Size Mix and Application I/O Characteristics It is always valuabl e to understand th e file size mix of the target dataset as well as the application I/O characte ristics. This includes t he number of concurrent streams, proportio ...

  • Quantum 6-01376-07 - page 9

    StorNext File System T uning File Size Mix and Application I/O Characteristics StorNext File System Tuning Guide 6 It is usually best to configure the RA ID stripe size no greater than 256K for optimal small file buffer cache performance. For more buffer cache configuration settings, see Mount Command Options on page 17. NFS / CIFS 0 It i s b es t ...

  • Quantum 6-01376-07 - page 10

    StorNext File System T uning The Metadata Network StorNext File System Tuning Guide 7 The Metadat a Network As with any client/server protocol, SNFS perfor mance is subject to the limitations of the underlying network. Therefore, it is recommended that you use a dedicated Metadata Networ k to avoid contention with other network traffic. Either 100B ...

  • Quantum 6-01376-07 - page 11

    StorNext File System T uning The Metadata Controller System StorNext File System Tuning Guide 8 Some metadata operations such as fi le creation can be CPU intensive, and benefit from increased CPU power. The MDC platform is important in these scenarios because lower clock- speed CPUs such as Sparc and M ips degrade performance. Other operations can ...

  • Quantum 6-01376-07 - page 12

    StorNext File System T uning The Metadata Controller System StorNext File System Tuning Guide 9 Example: [stripeGroup RegularFiles] S tatus UP Exclusive No ##Non-Exclusive stripeGroup for all Fi les## Read Enabled Wr it e Enabled S trip eBreadth 256K MultiPathMethod Rotate Node CvfsDisk6 0 Node CvfsDisk7 1 Affinities 0 Affinities are another stripe ...

  • Quantum 6-01376-07 - page 13

    StorNext File System T uning The Metadata Controller System StorNext File System Tuning Guide 10 Str i p eB re a dth 0 T h i s s e t t i n g m u s t m a t c h t h e R A I D s t r i p e s i z e o r b e a m u l t i p l e o f t h e R A I D stripe size. Matching th e RAID stripe size i s usually the most optimal setting. However, depending on the RAID ...

  • Quantum 6-01376-07 - page 14

    StorNext File System T uning The Metadata Controller System StorNext File System Tuning Guide 11 InodeCacheSize 0 This setting consumes about 800-1000 bytes of memory times the nu mber specified. Increasing t his value can reduce latency of any metadat a operation by performing a hot cache access to inode information instead of an I/O to get inode ...

  • Quantum 6-01376-07 - page 15

    StorNext File System T uning The Metadata Controller System StorNext File System Tuning Guide 12 Settings greater than 64K are not recommended because performance will be adversel y impacted due to in efficient metad ata I/O operations. Values less than 16K are not reco mmended in most scenarios because startup and failover time may be ad versely i ...

  • Quantum 6-01376-07 - page 16

    StorNext File System T uning The Metadata Controller System StorNext File System Tuning Guide 13 man cvfs_config page.) T he snfsdefrag man page explains the command options in greater detail. FSM hourly statistics reporting is another very useful tool. This can show you the mix of metadata operations be ing invoked by cl ient processes, as well as ...

  • Quantum 6-01376-07 - page 17

    StorNext File System T uning The Metadata Controller System StorNext File System Tuning Guide 14 SNFS supports the Windows Perfmon utility. This provides many useful statistics counters for the SNFS client component. To instal l, obtain a copy of cvfsperf .dll from the SCM team in Denver and copy it into the c:/ winnt/system32 directory on the SN F ...

  • Quantum 6-01376-07 - page 18

    StorNext File System T uning The Metadata Controller System StorNext File System Tuning Guide 15 The “PERF: VFS” trace shows throughput measured for the read or write system call and significant aspects of the I/O, incl uding: •D m a : D M A •B u f : B u f f e r e d • Eof: File extended • Algn: Well-formed DMA I/O • Shr: File is share ...

  • Quantum 6-01376-07 - page 19

    StorNext File System T uning The Metadata Controller System StorNext File System Tuning Guide 16 • Identify read/modify/w rite condition. If buffered VFS writes are causing De vice reads, it might be beneficial to match I/O request size to a multiple of t he “cachebufsize” (default 64KB; see mount_cvfs man page). Another way to avoid this is ...

  • Quantum 6-01376-07 - page 20

    StorNext File System T uning The Metadata Controller System StorNext File System Tuning Guide 17 Mount Command Options 0 The following SNFS mount command settings are explained in greater detail in the mount_cvfs man page. The default size of the buffer cache varies by platform and main memory size, and ranges between 32MB and 256M B. And, by defau ...

  • Quantum 6-01376-07 - page 21

    StorNext File System T uning The Distributed LAN (Disk Proxy) Networks StorNext File System Tuning Guide 18 SNFS External API 0 The SNFS External API might be useful in some scenarios because it offers programmatic use of special SN FS performance capabilities such as affinities, preallocation, and quality of service. For more information, see the ...

  • Quantum 6-01376-07 - page 22

    StorNext File System T uning The Distributed LAN (Disk Proxy) Networks StorNext File System Tuning Guide 19 is set to auto-detect but the host is set to 1000Mb/full , you will observe a high error rate and extremely poor perfor mance. On Linux the ethto ol command can be very useful to invest igate and a djust speed/duplex settings. In some cases, ...

  • Quantum 6-01376-07 - page 23

    StorNext File System T uning The Distributed LAN (Disk Proxy) Networks StorNext File System Tuning Guide 20 Figure 1 Multi-NIC Hardware and IP Configurati on Diagram In the diagram there are two subnetwork s: the blue subnetwork (10.0.0.x) and the red subnetwork (192.168.9.x). Se rvers such as S1 are connecte d to both the blue and red subnetwork s ...

  • Quantum 6-01376-07 - page 24

    StorNext File System T uning Distributed LAN Servers StorNext File System Tuning Guide 21 Distributed LAN Servers Distributed LAN Servers must ha ve suff icient memory. When a Distributed LAN Server does not have sufficient me mory, its performance in servicing Distributed LAN I/O requests might suffer. In some cases (particul arly on Windows,) it ...

  • Quantum 6-01376-07 - page 25

    StorNext File System T uning Distributed LAN Client Vs. Legacy Network Attached Storage StorNext File System Tuning Guide 22 Performance 0 DLC outperforms NFS and CIFS for single-stream I/O and provides higher aggregate bandwidth. For in ferior NFS client implementations, the difference can be more th an a factor of two. DLC also makes extremely ef ...

  • Quantum 6-01376-07 - page 26

    StorNext File System T uning Windows Memory Requirements StorNext File System Tuning Guide 23 Therefore, DLC provides incr eased st abilit y that is comparable to the StorNext SAN Client. Consistent Security Model 0 DLC clients hav e the same security mo del as StorNext SAN clients. When CIFS and NFS are used, some security models aren’t supporte ...

  • Quantum 6-01376-07 - page 27

    StorNext File System T uning Windows Memory Requirements StorNext File System Tuning Guide 24 The first is the Directory Cach e Size . The default is 10 (MB). If you do not have large directories, or do not pe rform lots of directory scans, this number can be reduced to 1 or 2 MB. The impact wil l be slightly slower directory lookups in directories ...

  • Quantum 6-01376-07 - page 28

    StorNext File System T uning Sample FSM Configuration File StorNext File System Tuning Guide 25 Sample FSM Configuration File This sample configuration file is locat ed in the SNFS install directory under the examples subdirectory named example.cfg. # **************************************************************************** # A global section fo ...

  • Quantum 6-01376-07 - page 29

    StorNext File System T uning Sample FSM Configuration File StorNext File System Tuning Guide 26 MAX(StripeBreadth) # MaxMBPerClientReserve 50 # in MBs, default 100 MB reserved per client # OpHangLimitSecs 300 # default 180 secs # DataMigrationThreadPoolSize 128 # Managed only, default 8 # ************************************************************ ...

  • Quantum 6-01376-07 - page 30

    StorNext File System T uning Sample FSM Configuration File StorNext File System Tuning Guide 27 [Disk CvfsDisk4] Status UP Type VideoDrive [Disk CvfsDisk5] Status UP Type VideoDrive [Disk CvfsDisk6] Status UP Type VideoDrive [Disk CvfsDisk7] Status UP Type VideoDrive [Disk CvfsDisk8] Status UP Type VideoDrive [Disk CvfsDisk9] Status UP Type VideoDr ...

  • Quantum 6-01376-07 - page 31

    StorNext File System T uning Sample FSM Configuration File StorNext File System Tuning Guide 28 [Disk CvfsDisk17] Status UP Type DataDrive # **************************************************************************** # A stripe section for defining stripe groups. # **************************************************************************** [Strip ...

  • Quantum 6-01376-07 - page 32

    StorNext File System T uning Sample FSM Configuration File StorNext File System Tuning Guide 29 [StripeGroup AudioFiles] Status UP Exclusive Yes ##Exclusive StripeGroup for Audio File Only## Affinity AudioFiles Read Enabled Write Enabled StripeBreadth 1M MultiPathMethod Rotate Node CvfsDisk10 0 Node CvfsDisk11 1 Node CvfsDisk12 2 Node CvfsDisk13 3 ...

Fabbricante Quantum Categoria Webcam

I documenti che otteniamo dal fabbricante del dispositivoQuantum 6-01376-07 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Quantum
- manuali per l’uso 6-01376-07
- schede prodotto Quantum
- opuscoli
- o etichette energetiche Quantum 6-01376-07
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Quantum 6-01376-07.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Quantum 6-01376-07, manuali di manutenzione, brevi manuali o manuali utente Quantum 6-01376-07. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Quantum 6-01376-07.

Manuali per l’uso simili

Manuale completo del dispositivo Quantum 6-01376-07, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Quantum 6-01376-07 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Quantum 6-01376-07.

Il manuale per l’uso completo Quantum, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Quantum 6-01376-07 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Quantum 6-01376-07, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Quantum 6-01376-07 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Quantum 6-01376-07 - che ci dovrebbe aiutare nei primi passi durante l'uso Quantum 6-01376-07
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Quantum 6-01376-07
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Quantum 6-01376-07 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Quantum 6-01376-07?

Utilizza il modulo sottostante

Se non hai risolto il problema con Quantum 6-01376-07 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Quantum 6-01376-07 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)