Italiano dropdown-ico

Manuale per l’uso Husqvarna 268K, 272K

24 pagine 0.69 mb
Scarica

Vai alla pagina of 24

Summary
  • Husqvarna 268K, 272K - page 1

    Svenska – 1 Operator ’ s Manual 268K/272K 101 87 70-27 Read through the Operator’s Manual carefully and understand the contents before you use the power cutter. ...

  • Husqvarna 268K, 272K - page 2

    2 –English WARNING! The power cutter can be dangerous! Careless and incorrect use can result in serious, even fatal injury. SYMBOL EXPLANA TION Symbols on the power cutter: Read through the Operator's Manual carefully and understand the contents before you use the power cutter. Checks and/or maintenance shall be carried out with the engine s ...

  • Husqvarna 268K, 272K - page 3

    English – 3 Before using your new Power cutter • Read the Operator’s Manual carefully. • Check the assembly and adjustment of the cutting disc, see chapter ” Assembly ”. • Start the engine and check the carburettor settings. See chapter ” Maintenance ”, section ” Carburettor ”. When adjusted correctly the cutting disc should n ...

  • Husqvarna 268K, 272K - page 4

    4 – English ! SAFETY INSTRUCTIONS ! ! WARNING! Incorrect or careless use of a power cutter can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand this manual. PERSONAL SAFETY EQUIPMENT WARNING! When using a power cutter, safety equipment approved by the appropriate aut ...

  • Husqvarna 268K, 272K - page 5

    English – 5 The silencer is designed to give the lowest possible noise level and to direct the engine‘s exhaust fumes away from the user. The engine‘s exhaust fumes are hot and can contain sparks, which can lead to the outbreak of fire. In countries that have a warm and dry climate the risk of forest fires is obvious. We have therefore fitted ...

  • Husqvarna 268K, 272K - page 6

    6 – English SAFETY INSTRUCTIONS GENERAL SAFETY INSTRUCTIONS IMPORTANT INFORMATION! Do not use the power cutter until you have read the entire contents of this Operator’s Manual. All servicing, in addition to the points listed in the section ” Control, maintenance and service of the power cutter’s safety equipment” , should be carried out ...

  • Husqvarna 268K, 272K - page 7

    English – 7 ! ! SAFETY INSTRUCTIONS ! Fuel safety (Filling/Fuel mixture/Storage) WARNING! Exercise great care when handling fuel. Bear in mind the risk of fire, explosions and inhaling fumes. • Never fill the machine while the engine is running. • Provide good ventilation when filling or mixing fuel (petrol and 2-stroke oil). • Move the mac ...

  • Husqvarna 268K, 272K - page 8

    8 – English SAFETY INSTRUCTIONS ! Over exposure to vibrations can result in blood-vessel or nerve injury to persons suffering with blood circulation problems. Seek medical attention if you experience physical symptoms that can be related to over exposure to vibrations. Examples of such symptoms are numbness, lack of feeling, “tickling“, “pr ...

  • Husqvarna 268K, 272K - page 9

    English – 9 SAFETY INSTRUCTIONS Pull in Pull in occurs when the lower part of the disc is suddenly stopped or when the cut closes. (To avoid this see the section ” How to avoid kickback ” and ”Pinching/rotation” below). Pinching/rotation Pinching occurs when the cut closes. The power cutter can be drawn suddenly and powerfully downwards. ...

  • Husqvarna 268K, 272K - page 10

    10 – English ! SAFETY INSTRUCTIONS CUTTING DISCS AND BLADES ! General Cutting discs and discs are available in two standard designs; abrasive discs and diamond discs. High speed portable tools Cutting discs of the make Husqvarna are manufactured for portable, high speed, power cutters. If other makes of cutting discs are used, ensure the discs co ...

  • Husqvarna 268K, 272K - page 11

    English – 11 SAFETY INSTRUCTIONS Cutting discs Type of cutting discs Check that the disc is approved for high speed, portable power cutters. Do not exceed the maximum working speed stated on the disc. Damage • Ensure the disc it not cracked or damaged in any other way. • Test the disc by hitting it gently with a piece of wood. If the disc doe ...

  • Husqvarna 268K, 272K - page 12

    12 – English WHA T IS WHA T? 1. Cutting trolley 2. Upper guide section 3. Locking lever for upper guide section 4. Fuel tank 5. Splash guard 6. Choke 7. Throttle catch 8. Stop switch 9. Cutting head 10. Cutting arm 11. Belt tensioning screw 12. Cutting disc What is what on a power cutter? 17 19 14 6 4 8 2 1 18 3 5 7 9 10 11 12 13 13 15 16 22 24 2 ...

  • Husqvarna 268K, 272K - page 13

    English – 13 ASSEMBL Y Checking the drive shaft and flanges • Check that the threads on the drive shaft are undamaged. • Check that the contact surfaces of the cutting disc and flanges are flat, run correctly on the spindle and are free from foreign objects. Do not use flanges that are twisted, have damaged edges, untrue or dirty. Do not use ...

  • Husqvarna 268K, 272K - page 14

    14 – English Two-stroke oil • For the best results use HUSQVARNA two-stroke oil, which has been specially produced for power cutters. Mixing ratio 1:50 (2%). • If HUSQVARNA two-stroke oil is not available you can use a high quality two- stroke oil intended for air cooled engines. Contact your dealer when selecting an oil. Mixing ratio: 1:33 ( ...

  • Husqvarna 268K, 272K - page 15

    English – 15 Starting a cold engine IGNITION: Slide the stop switch to the left. CHOKE: Pull out the choke. DECOMPRESSION VALVE (272K) Press in the value to reduce the pressure in the cylinder, this makes starting the power cutter easier. The decompression valve should always be used when starting. When the machine has started the value automatic ...

  • Husqvarna 268K, 272K - page 16

    16 – English MAINTENANCE ! WARNING! Never use a power cutter without a disc guard over the cutting disc. Changing the drive belt • Loosen the two nuts (A). • Turn the tensioning screws (B) until the tension has been released. • Remove the two nuts (A). • Remove the front belt cover (C). • Remove the belt from the pulley. • Dismantle t ...

  • Husqvarna 268K, 272K - page 17

    English – 17 ! MAINTENANCE Carburettor Operation, Basic settings, Fine tuning Operation • The carburettor governs the engine‘s speed via the throttle. Air/fuel is mixed in the carburettor. The air/fuel mixture is adjustable. To take advantage of the engine‘s optimal output the adjustment must be correct. • The setting of the carburettor m ...

  • Husqvarna 268K, 272K - page 18

    18 – English MAINTENANCE Fuel filter • The fuel filter sits inside the fuel tank. • The fuel tank must be protected from contamination when filling. This reduces the risk of operating disturbances caused by blockage of the fuel filter. • The filter cannot be cleaned but must be replaced with a new filter when it blocked. The filter should b ...

  • Husqvarna 268K, 272K - page 19

    English – 19 Replacing a broken or worn starter cord • Loosen the bolts that hold the starter against the crankcase and lift off the starter unit. • Pull out the cord approx. 30 cm and lift it out of the cut- out in the starter-pulley’s periphery. Reset the recoil spring by allowing the pulley to slowly rotate backwards. • Loosen the scre ...

  • Husqvarna 268K, 272K - page 20

    20 – English MAINTENANCE Spark plug The condition of the spark plug is affected by: • An incorrect carburettor setting. • An incorrect fuel mixture (too much oil). • A dirty air filter. These factors cause deposits on the spark plug electrode that may result in malfunction or starting difficulties. • If the machine is low on power, diffic ...

  • Husqvarna 268K, 272K - page 21

    English – 21 MAINTENANCE Below follows some general maintenance instructions. If you need further information please contact your service workshop. W eekly maintenance 9. Check the main filter. 10. Check that the anti-vibration elements are not damaged. 11. Clean the spark plug. Check that the electrode gap is 0.5 mm. 12. Clean the cooling fins o ...

  • Husqvarna 268K, 272K - page 22

    22 – English TECHNICAL DA T A Engine Cylinder volume, cu.in/cm 3 Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. speed, unloaded, rpm Power, kW Ignition system Manufacture Type of ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Manufacturer Carburettor type Fuel capacity, US pint/litre Weight ...

  • Husqvarna 268K, 272K - page 23

    English – 23 ...

  • Husqvarna 268K, 272K - page 24

    ´*2m"¶7ߨ 1998W17 ...

Fabbricante Husqvarna Categoria Brush Cutter

I documenti che otteniamo dal fabbricante del dispositivoHusqvarna 268K, 272K possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Husqvarna
- manuali per l’uso 268K, 272K
- schede prodotto Husqvarna
- opuscoli
- o etichette energetiche Husqvarna 268K, 272K
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Husqvarna 268K, 272K.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Husqvarna 268K, 272K, manuali di manutenzione, brevi manuali o manuali utente Husqvarna 268K, 272K. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Husqvarna 268K, 272K.

Manuali per l’uso simili

Manuale completo del dispositivo Husqvarna 268K, 272K, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Husqvarna 268K, 272K dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Husqvarna 268K, 272K.

Il manuale per l’uso completo Husqvarna, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Husqvarna 268K, 272K - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Husqvarna 268K, 272K, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Husqvarna 268K, 272K che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Husqvarna 268K, 272K - che ci dovrebbe aiutare nei primi passi durante l'uso Husqvarna 268K, 272K
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Husqvarna 268K, 272K
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Husqvarna 268K, 272K in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Husqvarna 268K, 272K?

Utilizza il modulo sottostante

Se non hai risolto il problema con Husqvarna 268K, 272K con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Husqvarna 268K, 272K è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)