Husqvarna 268K, 272Kの取扱説明書

24ページ 0.69 mb
ダウンロード

ページに移動 of 24

Summary
  • Husqvarna 268K, 272K - page 1

    Svenska – 1 Operator ’ s Manual 268K/272K 101 87 70-27 Read through the Operator’s Manual carefully and understand the contents before you use the power cutter. ...

  • Husqvarna 268K, 272K - page 2

    2 –English WARNING! The power cutter can be dangerous! Careless and incorrect use can result in serious, even fatal injury. SYMBOL EXPLANA TION Symbols on the power cutter: Read through the Operator's Manual carefully and understand the contents before you use the power cutter. Checks and/or maintenance shall be carried out with the engine s ...

  • Husqvarna 268K, 272K - page 3

    English – 3 Before using your new Power cutter • Read the Operator’s Manual carefully. • Check the assembly and adjustment of the cutting disc, see chapter ” Assembly ”. • Start the engine and check the carburettor settings. See chapter ” Maintenance ”, section ” Carburettor ”. When adjusted correctly the cutting disc should n ...

  • Husqvarna 268K, 272K - page 4

    4 – English ! SAFETY INSTRUCTIONS ! ! WARNING! Incorrect or careless use of a power cutter can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand this manual. PERSONAL SAFETY EQUIPMENT WARNING! When using a power cutter, safety equipment approved by the appropriate aut ...

  • Husqvarna 268K, 272K - page 5

    English – 5 The silencer is designed to give the lowest possible noise level and to direct the engine‘s exhaust fumes away from the user. The engine‘s exhaust fumes are hot and can contain sparks, which can lead to the outbreak of fire. In countries that have a warm and dry climate the risk of forest fires is obvious. We have therefore fitted ...

  • Husqvarna 268K, 272K - page 6

    6 – English SAFETY INSTRUCTIONS GENERAL SAFETY INSTRUCTIONS IMPORTANT INFORMATION! Do not use the power cutter until you have read the entire contents of this Operator’s Manual. All servicing, in addition to the points listed in the section ” Control, maintenance and service of the power cutter’s safety equipment” , should be carried out ...

  • Husqvarna 268K, 272K - page 7

    English – 7 ! ! SAFETY INSTRUCTIONS ! Fuel safety (Filling/Fuel mixture/Storage) WARNING! Exercise great care when handling fuel. Bear in mind the risk of fire, explosions and inhaling fumes. • Never fill the machine while the engine is running. • Provide good ventilation when filling or mixing fuel (petrol and 2-stroke oil). • Move the mac ...

  • Husqvarna 268K, 272K - page 8

    8 – English SAFETY INSTRUCTIONS ! Over exposure to vibrations can result in blood-vessel or nerve injury to persons suffering with blood circulation problems. Seek medical attention if you experience physical symptoms that can be related to over exposure to vibrations. Examples of such symptoms are numbness, lack of feeling, “tickling“, “pr ...

  • Husqvarna 268K, 272K - page 9

    English – 9 SAFETY INSTRUCTIONS Pull in Pull in occurs when the lower part of the disc is suddenly stopped or when the cut closes. (To avoid this see the section ” How to avoid kickback ” and ”Pinching/rotation” below). Pinching/rotation Pinching occurs when the cut closes. The power cutter can be drawn suddenly and powerfully downwards. ...

  • Husqvarna 268K, 272K - page 10

    10 – English ! SAFETY INSTRUCTIONS CUTTING DISCS AND BLADES ! General Cutting discs and discs are available in two standard designs; abrasive discs and diamond discs. High speed portable tools Cutting discs of the make Husqvarna are manufactured for portable, high speed, power cutters. If other makes of cutting discs are used, ensure the discs co ...

  • Husqvarna 268K, 272K - page 11

    English – 11 SAFETY INSTRUCTIONS Cutting discs Type of cutting discs Check that the disc is approved for high speed, portable power cutters. Do not exceed the maximum working speed stated on the disc. Damage • Ensure the disc it not cracked or damaged in any other way. • Test the disc by hitting it gently with a piece of wood. If the disc doe ...

  • Husqvarna 268K, 272K - page 12

    12 – English WHA T IS WHA T? 1. Cutting trolley 2. Upper guide section 3. Locking lever for upper guide section 4. Fuel tank 5. Splash guard 6. Choke 7. Throttle catch 8. Stop switch 9. Cutting head 10. Cutting arm 11. Belt tensioning screw 12. Cutting disc What is what on a power cutter? 17 19 14 6 4 8 2 1 18 3 5 7 9 10 11 12 13 13 15 16 22 24 2 ...

  • Husqvarna 268K, 272K - page 13

    English – 13 ASSEMBL Y Checking the drive shaft and flanges • Check that the threads on the drive shaft are undamaged. • Check that the contact surfaces of the cutting disc and flanges are flat, run correctly on the spindle and are free from foreign objects. Do not use flanges that are twisted, have damaged edges, untrue or dirty. Do not use ...

  • Husqvarna 268K, 272K - page 14

    14 – English Two-stroke oil • For the best results use HUSQVARNA two-stroke oil, which has been specially produced for power cutters. Mixing ratio 1:50 (2%). • If HUSQVARNA two-stroke oil is not available you can use a high quality two- stroke oil intended for air cooled engines. Contact your dealer when selecting an oil. Mixing ratio: 1:33 ( ...

  • Husqvarna 268K, 272K - page 15

    English – 15 Starting a cold engine IGNITION: Slide the stop switch to the left. CHOKE: Pull out the choke. DECOMPRESSION VALVE (272K) Press in the value to reduce the pressure in the cylinder, this makes starting the power cutter easier. The decompression valve should always be used when starting. When the machine has started the value automatic ...

  • Husqvarna 268K, 272K - page 16

    16 – English MAINTENANCE ! WARNING! Never use a power cutter without a disc guard over the cutting disc. Changing the drive belt • Loosen the two nuts (A). • Turn the tensioning screws (B) until the tension has been released. • Remove the two nuts (A). • Remove the front belt cover (C). • Remove the belt from the pulley. • Dismantle t ...

  • Husqvarna 268K, 272K - page 17

    English – 17 ! MAINTENANCE Carburettor Operation, Basic settings, Fine tuning Operation • The carburettor governs the engine‘s speed via the throttle. Air/fuel is mixed in the carburettor. The air/fuel mixture is adjustable. To take advantage of the engine‘s optimal output the adjustment must be correct. • The setting of the carburettor m ...

  • Husqvarna 268K, 272K - page 18

    18 – English MAINTENANCE Fuel filter • The fuel filter sits inside the fuel tank. • The fuel tank must be protected from contamination when filling. This reduces the risk of operating disturbances caused by blockage of the fuel filter. • The filter cannot be cleaned but must be replaced with a new filter when it blocked. The filter should b ...

  • Husqvarna 268K, 272K - page 19

    English – 19 Replacing a broken or worn starter cord • Loosen the bolts that hold the starter against the crankcase and lift off the starter unit. • Pull out the cord approx. 30 cm and lift it out of the cut- out in the starter-pulley’s periphery. Reset the recoil spring by allowing the pulley to slowly rotate backwards. • Loosen the scre ...

  • Husqvarna 268K, 272K - page 20

    20 – English MAINTENANCE Spark plug The condition of the spark plug is affected by: • An incorrect carburettor setting. • An incorrect fuel mixture (too much oil). • A dirty air filter. These factors cause deposits on the spark plug electrode that may result in malfunction or starting difficulties. • If the machine is low on power, diffic ...

  • Husqvarna 268K, 272K - page 21

    English – 21 MAINTENANCE Below follows some general maintenance instructions. If you need further information please contact your service workshop. W eekly maintenance 9. Check the main filter. 10. Check that the anti-vibration elements are not damaged. 11. Clean the spark plug. Check that the electrode gap is 0.5 mm. 12. Clean the cooling fins o ...

  • Husqvarna 268K, 272K - page 22

    22 – English TECHNICAL DA T A Engine Cylinder volume, cu.in/cm 3 Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. speed, unloaded, rpm Power, kW Ignition system Manufacture Type of ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Manufacturer Carburettor type Fuel capacity, US pint/litre Weight ...

  • Husqvarna 268K, 272K - page 23

    English – 23 ...

  • Husqvarna 268K, 272K - page 24

    ´*2m"¶7ߨ 1998W17 ...

メーカー Husqvarna カテゴリー Brush Cutter

Husqvarna 268K, 272Kのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 268K, 272Kの取扱説明書
- Husqvarnaの製品カード
- パンフレット
- またはHusqvarna 268K, 272Kの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Husqvarna 268K, 272Kの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Husqvarna 268K, 272Kの取り付け説明書、サービスマニュアル、簡易説明書、またはHusqvarna 268K, 272Kのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Husqvarna 268K, 272Kの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Husqvarna 268K, 272Kデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHusqvarna 268K, 272Kを使用するのを助ける技術的文書のことです。説明書は通常、全てのHusqvarna 268K, 272Kユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Husqvarnaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Husqvarna 268K, 272Kの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHusqvarna 268K, 272Kの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Husqvarna 268K, 272Kに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Husqvarna 268K, 272Kデバイスの基本機能を使うにあたってのヒント。 Husqvarna 268K, 272Kのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Husqvarna 268K, 272Kに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHusqvarna 268K, 272Kのメーカー/サービスへの連絡先に関する情報。

Husqvarna 268K, 272Kについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHusqvarna 268K, 272Kの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHusqvarna 268K, 272Kで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)