Italiano dropdown-ico

Manuale per l’uso Cleveland Range KET-3-T

28 pagine 2.36 mb
Scarica

Vai alla pagina of 28

Summary
  • Cleveland Range KET-3-T - page 1

    SE95004 Rev . 4 Operators Manual Installation, Operation & Service Electric T able T op Kettles For units built after August 1999 MODELS: Single Kettles KET -3-T KET -6-T KET -12-T KET -20-T* T win Kettles TKET -3-T TKET -6-T TKET -12-T * Floor T ype Leg Mount 1333 East 179th S t., Cleveland, Ohio, U.S.A. 441 10 Phone: (216) 481-4900 Fax: (216) ...

  • Cleveland Range KET-3-T - page 2

    T ABLE OF CONTENTS Installation General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Shipping Damage Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation . . . . . . . . . . . . ...

  • Cleveland Range KET-3-T - page 3

    1 GENERAL Installation of the kettle must be accomplished by qualified electrical installation personnel working to all applicable local and national codes. Improper installation of pr oduct could cause injur y or damage. This equipment is built to comply with applicable standards for manufactur ers. Included among those approval agencies ar e: UL, ...

  • Cleveland Range KET-3-T - page 4

    2 ASSEMBL Y T able-T op Models (3, 6 & 12 gallon) Base Mounting Diagram T able-top models (3, 6 & 12 gallon - single and twin) must be positioned on a firm, level stand, or existing counter top, and bolted in place. These models are supplied with four threaded mounting bushings welded to the underside of the base. An optional support stand ...

  • Cleveland Range KET-3-T - page 5

    3 W A TER The sealed jacket of the electric kettle is precharged with the corr ect amount of a water based formula, and therefore, no water connection is requir ed to the kettle jacket. The kettle can be equipped with optional hot and/or cold water faucet, requiring 1/2" copper tubing as supply lines. INST ALLA TION CHECKS Although the kettle ...

  • Cleveland Range KET-3-T - page 6

    4 6 5 4 3 2 1 7 OPERA TING INSTRUCTIONS General Parts Drawing ITEM # DESCRIPTION FUNCTION 1. Tilting Handle Used for tilting the kettle. 2. V acuum/Pressur e Gauge Indicate steam pressur e in PSI inside steam jacket as well as vacuum in inches of mercury . 3. Pressur e Relief V alve This valve is used to vent the kettle and in the unlikely event th ...

  • Cleveland Range KET-3-T - page 7

    5 OPERA TING THE KETTLE DO NO T LEAN ON OR PLA CE OBJECTS ON KETTLE LIP . SERIOUS INJUR Y COULD RESUL T IF KETTLE TIPPED O VER, SPILLING HO T CONTENTS. 1. Before turning kettle on, read the V acuum/Pressur e Gauge ( 2 ). The gauges needle should be in the green zone. If the needle is in the " VENT AIR " zone, refer to the Kettle V enting ...

  • Cleveland Range KET-3-T - page 8

    6 MARINE LOCK Y our unit is equipped with a marine lock to prevent accidental tilting. The following procedur e should be used to tilt the kettle. 1. Grasp the tilt handle. 2. Hold the latch down to unlock tilting mechanism. 3. Pull the handle to tilt kettle. 4. T o lock, return the kettle to its upright position and push handle back. NOTE: Inspect ...

  • Cleveland Range KET-3-T - page 9

    7 MARINE LOCK Use a small nylon bristle brush to remove food and debris from pivot point. If lock is still sticking have maintenance disassemble and clean pieces individually and reassemble. Disassembly 1. Disconnect power from kettle. 2. Remove console cover from top of kettle's console. 3. Remove locknut and lockwasher from inside console. 4 ...

  • Cleveland Range KET-3-T - page 10

    8 F AUCET ASSEMBL Y ITEM P ART DESCRIPTION QTY . NO . NO . 1. KE50825-2 3/4" Spout (KET -3/6/12/20-T) . . . . . . .1 KE50825-9 3/4" Spout (TKET -3/6/12-T) . . . . . . . . .1 2. F A95022 Retaining Ring . . . . . . . . . . . . . . . . . .1 3. F A05002-19 "O" Ring . . . . . . . . . . . . . . . . . . . . . . .1 4. KE51736 Long Fauce ...

  • Cleveland Range KET-3-T - page 11

    9 KETTLE BOTTOM & SIDE ITEM NO . P ART NO . DESCRIPTION QTY . 1. KE50556-1 Probe, Low W ater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE51723 Safety V alve, 50 PSI, 1/2" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. KE52455 Bottom Cover Gasket, 3 gallon kettle . . . . . . ...

  • Cleveland Range KET-3-T - page 12

    10 2 3 4 5 1 CORD & PLUG OPTION ITEM NO . P ART NO . DESCRIPTION QTY . FOR KET -6-T (SW) (200-240V AC, 3PH, 50/60Hz 1. KE02113-1 Cord Plug Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2. KE54819-1 Plug (30A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3. KE5 ...

  • Cleveland Range KET-3-T - page 13

    11 CONSOLE COMPONENTS & MARINE LOCK 5 4 6 7 10 9 8 11 12 13 26 23 5 2 3 1 14 15 25 16 18 19 20 21 17 24 22 ...

  • Cleveland Range KET-3-T - page 14

    12 CONSOLE COMPONENTS & MARINE LOCK ITEM NO . P ART NO . DESCRIPTION QTY . Single / T win 1. SE00114 Potentiometer with ON/OFF Switch, c/w Item #2 . . . . . . . . . . . . . . . . . . . . . . 1 / 2 2. KE51005 Rubber Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 / 2 3. KE50569-1 Knob, Poten ...

  • Cleveland Range KET-3-T - page 15

    13 NOTE: Item # 14 to be tack welded flush outside in the gearbox housing (item #1 ). Do not damage the outside edges of the gearbox housing when tack welding. 1 14 2 2 3 7 8 7 9 3 5 6 20 19 22 23 21 25 10 11 4 12 13 16 15 12 24 18 17 TIL TING GEARBOX ASSEMBL Y (12 gallon kettle only) ITEM NO . P ART NO . DESCRIPTION QTY . 1.-16. KE02062-1 Tilting ...

  • Cleveland Range KET-3-T - page 16

    14 ELECTRICAL P ANEL ITEM NO . P ART NO . DESCRIPTION QTY . Single / T win 1. KE54761 T er minal Block Mounting Strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 / 2 2. SK50055-1 T er minal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 / 6 3. SK50054-2 T er minal Block End Anchor . . . . . ...

  • Cleveland Range KET-3-T - page 17

    15 Cleveland Range equipment requir es little preventative maintenance. We do however pr ovide the following chart as a guideline for inspection and maintenance to keep your unit functioning at 100%. INSPECTION AND MAINTENANCE CHECK LIST The following check should be completed every six months or more frequently if unit is in a high volume facility ...

  • Cleveland Range KET-3-T - page 18

    16 BEARING LUBRICA TING PROCEDURE 1. Remove console cover . 2. Loosen two Allen screws on locking ring. 3. Pull locking ring to center of trunnion. 5. Clean newly exposed sections of trunnion. 6. Grease trunnion between kettle and console. 7. Repack outer needle bearing. 8. Push kettle back in place. 10. Reinstall trunnion and lock collar . 11. Rep ...

  • Cleveland Range KET-3-T - page 19

    17 CALIBRA TING PROCEDURE 1. Insure the unit has a vacuum befor e you begin calibrating procedur es. If unit requires venting r efer to Kettle V enting Instructions on page 18 of this manual. 2. T ur n kettle ON and set temperatur e dial to 10 ( Max.). 3. Allow the unit to cycle twice. 4. Check temperature of the inner kettle surface with a digital ...

  • Cleveland Range KET-3-T - page 20

    3. Remove Guard Bracket (A). 4. Pull Pressur e Relief V alve (B) open to insure vessel is not pressurized. 5. Remove Pressur e Relief V alve (B). 6. Replace Pressur e Relief V alve (B) with Street Elbow (C). 7. Add distilled water (D) through the Str eet Elbow (C), using a funnel if necessary . Refer to Distilled W ater Requirements chart for the p ...

  • Cleveland Range KET-3-T - page 21

    MARINE LOCK TESTING PROCEDURE 1. Check that lock clears stop pin on side box without rubbing when kettle is tilted (Figure A ). 2. Check side to side play . Lock should remain fully over stop pin when pushed to it's maximum side to side play (Figure B ). 3. Check that the kettle when pushed fully upright moves the lock to a closed position. T ...

  • Cleveland Range KET-3-T - page 22

    20 Fault Isolation Pr ocedur e Step T est 1. Is there pr oper incoming voltage at terminal block? 2. Is the red LED illuminated? 3. Is the green LED illuminated? 4. Do both contactors energize? 5. Measure continuity acr oss safety thermostat. Is it an open circuit? 6. Is there 120 V AC present acr oss the coils of the contactors? 7. Remove wire fr ...

  • Cleveland Range KET-3-T - page 23

    21 Fault Isolation Pr ocedur e Step T est 1. In a cold state, does the pressur e gauge read in the gr een zone? 2. Do the contactors shut off too early? (before r eaching nor mal maximum operating pressur e.) 3. Does the green LED r emain illuminated after the contactors shut off? 4. Unplug control box and measur e the resistance acr oss potentiome ...

  • Cleveland Range KET-3-T - page 24

    22 5. Remove kettle thermistor and allow to cool. Remove edge connector from control box. T est resistance acr oss edge connector's pins #2 and #7. Is it approximately 100,000 ohms? 6. T urn the potentiometer on the control box clockwise to increase the maximum operating temperature. Does the kettle now achieve maximum operating pressur e of 3 ...

  • Cleveland Range KET-3-T - page 25

    23 WIRING DIAGRAM 3 Gallon Kettles 200-240v Single Phase Only 380-480v Single Phase Only ...

  • Cleveland Range KET-3-T - page 26

    24 WIRING DIAGRAM 6-20 Gallon 200-240v 380-600v ...

  • Cleveland Range KET-3-T - page 27

    25 25 ON MARCHE ENCENDIDO ACCESO AN P AUSE, INTERRUPTION P AUSE, INTERRUPTION P AUSA, INTERRUPCION P AUSA, INTERRUZIONE P AUSE, UNTERBRECHUNG RESET R É ENCLENCHER RECONECT AR RESET NULLSTELLEN STOP OF ACTION ARR Ê T DE L'ACTION P ARAR FUNCIONAMIENTO ARRESTO OPERAZIONE FUNKTION STOPPEN F AST STOP , EMERGENCY ARR Ê T RAPIDE D'URGENCE P A ...

  • Cleveland Range KET-3-T - page 28

    26 26 LOW W A TER NIVEAU BAS DE L'EAU NIVEL DE AGUA BAJO LIVELLO BASSO W ASSERST AND NIEDRIG IGNITION F AILURE P ANNE D'ALLUMAGE F ALLO DE ENCENDIDO MANCA T A ACCENSIONE Z Ü NDUNGSFEHLER COOLING REFROIDISSEMENT REFRIGERACION RAFFREDDAMENTO K Ü HLUNG MIXER BRIDGE PONT DU M É LANGEUR PUENTE DE MEZCLADORA MENSOLA MESCOLA TORE MISCHER-BR ? ...

Fabbricante Cleveland Range Categoria Hot Beverage Maker

I documenti che otteniamo dal fabbricante del dispositivoCleveland Range KET-3-T possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cleveland Range
- manuali per l’uso KET-3-T
- schede prodotto Cleveland Range
- opuscoli
- o etichette energetiche Cleveland Range KET-3-T
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cleveland Range KET-3-T.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cleveland Range KET-3-T, manuali di manutenzione, brevi manuali o manuali utente Cleveland Range KET-3-T. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cleveland Range KET-3-T.

Manuali per l’uso simili

Manuale completo del dispositivo Cleveland Range KET-3-T, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cleveland Range KET-3-T dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cleveland Range KET-3-T.

Il manuale per l’uso completo Cleveland Range, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cleveland Range KET-3-T - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cleveland Range KET-3-T, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cleveland Range KET-3-T che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cleveland Range KET-3-T - che ci dovrebbe aiutare nei primi passi durante l'uso Cleveland Range KET-3-T
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cleveland Range KET-3-T
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cleveland Range KET-3-T in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cleveland Range KET-3-T?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cleveland Range KET-3-T con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cleveland Range KET-3-T è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)