Manuale per l’uso Bryant TSTAT

16 pagine 0.13 mb
Scarica

Vai alla pagina of 16

Summary
  • Bryant TSTAT - page 1

    NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. INDEX Page SAFETY CONSIDERATIONS .....................................................1 INTRODUCTION ..........................................................................1 INSTALLATION CONSIDERATIONS ............. ...

  • Bryant TSTAT - page 2

    • Close to or in a frequently used room, preferably on an inside partitioning wall. • On a section of wall without pipes or duct work. Thermostat should NOT be mounted: • Close to a window, on an outside wall, or next to a door leading to the outside. • Exposed to direct light and heat from a lamp, sun, fireplace, or other temperature-radia ...

  • Bryant TSTAT - page 3

    On power up, all display segments will light for 5 sec. For the next 5 sec, a 2-digit code appears on large display which identifies thermostat configuration: 1. AC—for 1-speed air conditioner 2. HP—for 1-speed heat pump 3. A2—for 2-speed air conditioner 4. H2—for 2-speed heat pump 5. HS—for intelligent heat staging with FK, FV Fan Coil a ...

  • Bryant TSTAT - page 4

    1. Enter configuration mode if not already there. See above. Use up and down buttons to make small (now flashing) display indicate 03. 2. Press SET TIME/TEMP button once to flash current selection of F or C. Factory default is F. 3. Use up and down buttons to move between F and C on large display. 4. Press SET TIME/TEMP button again to flash upper ...

  • Bryant TSTAT - page 5

    TO TEST HEATING: Press MODE button until HEAT icon under it turns on. Press up button until HEAT set point (LOWER right 2 digit display with HEAT now flashing under it) is 2° or 3° (not more) above room temperature. This will create a Heat Stage 1 demand. A small triangle to the left of this HEAT icon will flash or come on continually. Flashing m ...

  • Bryant TSTAT - page 6

    → TABLE 2—PROGRAMMABLE THERMOSTAT QUICK REFERENCE THERMOSTAT OUTPUT TSTAT Model Outdoor Unit AC/HP Configuration (Switch C) Staging Configuration (Switch D) 24v Hot Common Fan Heat Stage 1 Heat Stage 2 Heat Stage 3 Heat Stage 4 Cool Stage 1 Cool Stage 2 Reversing Valve AC01-B AC EITHER EITHER R C G W/W1 N/A N/A N/A Y/Y2 N/A N/A HP01-B HP OFF EI ...

  • Bryant TSTAT - page 7

    → Fig. 2—Single-Speed Air Conditioner with Single- Stage Furnace—Model AC Thermostat A98485 24 VAC HOT FAN HEAT STAGE 1 COOL STAGE 1 N/A N/A R G W/W1 Y/Y2 O/W2 Y1/W2 R G W Y 24 VAC COMM N/A OUTDOOR SENSOR CONNECTION C B S1 S2 C Y C MODEL AC THERMOSTAT SINGLE-STAGE FURNACE SINGLE-SPEED AIR CONDITIONER See note 1 SUGGESTED DIP SWITCH SETTINGS O ...

  • Bryant TSTAT - page 8

    → Fig. 7—Single-Speed Heat Pump with Typical Fan Coil—Model HP Thermostat A98490 24 VAC HOT FA N RVS COOLING COOL /HEAT STAGE 1 HEAT STAGE 2 N/ A R G W/W1 Y/Y2 O/W2 Y1/W2 R G 24 VAC COMM N/A OUTDOOR SENSOR CONNECTION C B S1 S2 C Y C MODEL HP THERMOSTAT TYPICAL FAN COIL SINGLE-SPEED HEAT PUMP See notes 3, 7, and 8 Y W2 * W3 E R O W2 SUGGESTED ...

  • Bryant TSTAT - page 9

    → Fig. 11—Two-Speed Heat Pump with Single-Stage Furnace —Model 2S Thermostat A98494 COOL/HEAT STAGE 1 RVS COOLING HEAT STAGE 3 COOL/HEAT STAGE 2 FAN 24 VAC HOT R W/W1 Y/Y2 O/W2 Y1/W2 G 24 VAC COMM N/A OUTDOOR SENSOR CONNECTION C B S1 S2 C Y Y2 C W2 MODEL 2S THERMOSTAT SINGLE-STAGE FURNACE TWO-SPEED HEAT PUMP See notes 3, 9, and 11 R Y1 O R W3 ...

  • Bryant TSTAT - page 10

    → Fig. 15—Single-Speed Air Conditioner with Variable-Speed Fan Coil (FK, FV) —Model AC Thermostat A98498 24 VAC HOT HEAT STAGE 1 N/A FAN N/A COOL STAGE 1 R R 24 VAC COMM N/A OUTDOOR SENSOR CONNECTION C B S1 S2 C G G C MODEL AC THERMOSTAT EASY SELECT TERMINAL BOARD J1 JUMPER J2 JUMPER SINGLE-SPEED AIR CONDITIONER See notes 1 and 8 DH Y1 O Y1/W ...

  • Bryant TSTAT - page 11

    → Fig. 19—Single-Speed Packaged Air Conditioner with Single-Stage Gas Furnace (588A, 589A) A98502 24 VAC HOT FAN HEAT STAGE 1 COOL STAGE 1 N/A N/A R G W/W1 Y/Y2 Y1/W2 O/W2 B S1 S2 MODEL AC THERMOSTAT RED GRN WHT YEL BRN See notes 1 and 11 C 24 VAC COMM N/A SPLICE BOX SUGGESTED DIP SWITCH SETTINGS ON ABC D OUTDOOR SENSOR CONNECTION → Fig. 17? ...

  • Bryant TSTAT - page 12

    → Fig. 23—Single-Speed Packaged Heat Pump with 2-Stage Electric Heat (665A, 657A, 664A) A98506 R G Y/Y2 Y1/W2 B S1 S2 MODEL HP THERMOSTAT SPLICE BOX VIO ORN WHT RED (TRAN) BRN WHT BRN See notes 3, 10, 11, and 12 C O/W2 W/W1 24 VAC COMM N/A OUTDOOR SENSOR CONNECTION HEATER CONTROL BOX YEL GRN RED RED PNK HEAT STAGE 2 COOL/HEAT STAGE 1 RVS COOLIN ...

  • Bryant TSTAT - page 13

    → WIRING DIAGRAM NOTES 1. The AC model thermostat can only control 1-stage cool and 1-stage heat. Dip Switch-C on has no controlling function and can either be ON or OFF. 2. HP and 2S model thermostat MUST have Dip Switch-C ON when installed in air conditioner applications. If required, second-stage heat is controlled by O/W2. Refer to indoor equ ...

  • Bryant TSTAT - page 14

    → OPERATIONAL INFORMATION FIVE-MINUTE COMPRESSOR TIMEGUARD This timer prevents the compressor from starting unless it has been off for at least 5 minutes. It can be defeated for 1 cycle by simultaneously pressing the FAN mode button and the INCREASE TEMPERATURE button. FIFTEEN-MINUTE CYCLE TIMER This timer prevents the start of a heating or cooli ...

  • Bryant TSTAT - page 15

    A98508 PROGRAMMABLE THERMOSTAT CONFIGURATION RECORD Date Owner/Operator A) Hardware Configuration  Switch A Zoning Selection. (OFF = Disable, ON = Enable)  Switch B Smart Recovery. (OFF = Enable, ON = Disable)  Switch C Heat Pump Operation. (OFF = Enable, ON = Disable)  Switch D Intelligent Heat Staging. (OFF = D ...

  • Bryant TSTAT - page 16

    SERVICE TRAINING Packaged Service Training programs are an excellent way to increase your knowledge of the equipment discussed in this manual, including:  • Unit Familiarization • Maintenance  • Installation Overview • Operating Sequence A large selection of product, theory, and skills programs is available, us ...

Fabbricante Bryant Categoria Thermostat

I documenti che otteniamo dal fabbricante del dispositivoBryant TSTAT possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Bryant
- manuali per l’uso TSTAT
- schede prodotto Bryant
- opuscoli
- o etichette energetiche Bryant TSTAT
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Bryant TSTAT.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Bryant TSTAT, manuali di manutenzione, brevi manuali o manuali utente Bryant TSTAT. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Bryant TSTAT.

Manuali per l’uso simili

Manuale completo del dispositivo Bryant TSTAT, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Bryant TSTAT dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Bryant TSTAT.

Il manuale per l’uso completo Bryant, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Bryant TSTAT - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Bryant TSTAT, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Bryant TSTAT che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Bryant TSTAT - che ci dovrebbe aiutare nei primi passi durante l'uso Bryant TSTAT
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Bryant TSTAT
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Bryant TSTAT in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Bryant TSTAT?

Utilizza il modulo sottostante

Se non hai risolto il problema con Bryant TSTAT con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Bryant TSTAT è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)