-
Harbor Freight Tools 93974 - page 1
37 PIECE SPRA Y GUN KIT ASSEMBL Y and OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com For technical questions and replacement parts, please call 1-800-444-3353 Model 93974 ® Cop yr ight © 2006 by Harbor F reight T ools ® . All r ights reser v ed. No por tion of this manu ...
-
Harbor Freight Tools 93974 - page 2
Page 2 SKU 93974 For technical questions, please call 1-800-444-3353 Specifications Save This Manual Y ou will need the manual for the saf ety warnings and precautions, assemb ly instr uctions , operating and maintenance procedures, par ts list and diagr am. K eep your in voice with this manual. Write the inv oice number on the inside of the front ...
-
Harbor Freight Tools 93974 - page 3
Page 3 SKU 93974 For technical questions, please call 1-800-444-3353 9. Maintain tools with care . K eep tools clean f or better and safer perf or mance. Follo w instructions for lubricating and changing accessor ies . Inspect tool cords and air hoses per iodically and, if damaged, ha ve them repaired b y an author ized technician. The handles must ...
-
Harbor Freight Tools 93974 - page 4
Page 4 SKU 93974 For technical questions, please call 1-800-444-3353 21. Read all of the information concerning coating pr oducts and cleaning solvents. Chlorinated solvents (e.g. 1-1-1 T richlorethylene and Meth ylene Chlor ide , also known as meth yl chlor ide) can chemically react with aluminum and ma y explode . Many paint spra yers contain alu ...
-
Harbor Freight Tools 93974 - page 5
Page 5 SKU 93974 For technical questions, please call 1-800-444-3353 Unpac king When unpacking, chec k to make sure the par ts listed on pages 14 and 16 are included. If any par ts are missing or brok en, please call Harbor F reight T ools at the number on the co v er of this manual as soon as possible . F or best ser vice y ou should incor porate ...
-
Harbor Freight Tools 93974 - page 6
Page 6 SKU 93974 For technical questions, please call 1-800-444-3353 Large Spra y Gun Small Spray Gun T rigger (14a) Air Cap (1a) Fluid Nozzle (4a) Fluid Control Knob (28a) Air Inlet (23a) Air Cap Set (1S) Cup (47) P atter n Control Knob (13) Fluid Control Knob (29) T rigger (38) Air Inlet (40) P aint Cup (34a) P atter n Control Knob (12a) Figure 1 ...
-
Harbor Freight Tools 93974 - page 7
Page 7 SKU 93974 For technical questions, please call 1-800-444-3353 Preparation Note: Proper paint material mixture helps to ensure less problems . Be sure to f ollow the manuf acturer’ s directions. Most materials will spra y readily if they are thinned properly . General tips for Preparation: 1. Mix and thin the paint/materials thoroughly acco ...
-
Harbor Freight Tools 93974 - page 8
Page 8 SKU 93974 For technical questions, please call 1-800-444-3353 F an Direction and P attern Adjustment F an Direction T o change the direction of the f an from hor iz ontal to ver tical, loosen the Loc k Ring and tur n the Air Cap (1 or 1a) 90 degrees . After the adjustment, tighten the Loc k Ring by hand. See FIGURE 2 below . Note: Alwa ys ma ...
-
Harbor Freight Tools 93974 - page 9
Page 9 SKU 93974 For technical questions, please call 1-800-444-3353 3. T urn the Fluid Control Knob (28a or 29) clockwise until it is fully closed. See FIGURE 1 on page 6. 4. After setting up a piece of scrap material, squeeze the T rigger in shor t bursts while tur ning the Fluid Control Knob countercloc kwise and obser ve the spra y patter ns un ...
-
Harbor Freight Tools 93974 - page 10
Page 10 SKU 93974 For technical questions, please call 1-800-444-3353 2. T o ensure y ou don’t allow paint to build up , star t moving the Spra y Gun bef ore you Squeeze the T rigger . When you are finished spr a ying, release the T r igger bef ore you stop moving the Spr a y Gun. Doing so will eliminate distinct ov er laps, producing a blended ( ...
-
Harbor Freight Tools 93974 - page 11
Page 11 SKU 93974 For technical questions, please call 1-800-444-3353 Operation P aint and Materials Preparation V erify with the paint or mater ials supplier the percentage of thinning required f or use with these Spra yers. T r y thinning a small amount and testing the spra y action. Thoroughly mix material before testing. Viscosity Viscosity is ...
-
Harbor Freight Tools 93974 - page 12
Page 12 SKU 93974 For technical questions, please call 1-800-444-3353 Maintenance SOL VENT SELECTION Alwa ys follo w the paint manufacturer’ s recommendations f or cleaning, solvent type, and disposing of used solvent. Latex P aints: Use warm, soapy w ater . IMPOR T ANT : Do not use mineral spirits on late x paints or the mixture will cong eal ma ...
-
Harbor Freight Tools 93974 - page 13
Page 13 SKU 93974 For technical questions, please call 1-800-444-3353 Disconnect from the air source. W arning! The Paint Cup and Spra y Gun may still hold air pressure, fire the Spray Gun towar d scrap material until all of the pressure is expended. 1 . Remov e the P aint Cup . 2 . P our residual paint into the paint container and seal it. 3 . P o ...
-
Harbor Freight Tools 93974 - page 14
Page 14 SKU 93974 For technical questions, please call 1-800-444-3353 NO TE : Some par ts are listed and shown for illustr ation pur poses only and are not a vailab le individually as replacement par ts. P ar ts List, Large Gun ...
-
Harbor Freight Tools 93974 - page 15
Page 15 SKU 93974 For technical questions, please call 1-800-444-3353 ...
-
Harbor Freight Tools 93974 - page 16
Page 16 SKU 93974 For technical questions, please call 1-800-444-3353 P ar ts List, Small Gun Diagram Note: When ordering par ts from this diagram add an “A” suffix. F or e xample Air Cap is par t number 1A. P atter n Control Knob Air Inlet Fluid Control Knob ...
-
Harbor Freight Tools 93974 - page 17
Page 17 SKU 93974 For technical questions, please call 1-800-444-3353 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIB UT OR HAS PRO VIDED THE P AR TS DIAGRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y . NEITHER THE MANUF ACTURER NOR DISTRIBUT OR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND T O THE BUYER THA T HE OR SHE ...
-
Harbor Freight Tools 93974 - page 18
Page 18 SKU 93974 For technical questions, please call 1-800-444-3353 T roub leshooting Spray P attern Diagnosis The P atter ns below resemble symptoms of spra y patter n prob lems. Please refer to the accompanying possib le problems if you are e xperiencing similar difficulties. The solution to each problem f ollows the prob lem in parentheses. Pr ...
-
Harbor Freight Tools 93974 - page 19
Page 19 SKU 93974 For technical questions, please call 1-800-444-3353 T roubleshooting (contin ued) 1. Low material le vel 2. Cup tipped too f ar 3. Clogged Air V ent 4. Loose fluid inlet connections 5. Dr y or loose fluid needle P acking Nut 6. Loose/damaged fluid tip/seat 1. No pressure at gun 2. Fluid control not open enough 3. Fluid too thick 1 ...
Hai una domanda su Harbor Freight Tools 93974?
Utilizza il modulo sottostante
Se non hai risolto il problema con Harbor Freight Tools 93974 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Harbor Freight Tools 93974 è probabile che voglia condividere il modo di risolverlo.