-
Harbor Freight Tools 93974 - page 1
37 PIECE SPRA Y GUN KIT ASSEMBL Y and OPERA TING INSTR UCTIONS 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com For technical questions and replacement parts, please call 1-800-444-3353 Model 93974 ® Cop yr ight © 2006 by Harbor F reight T ools ® . All r ights reser v ed. No por tion of this manu ...
-
Harbor Freight Tools 93974 - page 2
Page 2 SKU 93974 For technical questions, please call 1-800-444-3353 Specifications Save This Manual Y ou will need the manual for the saf ety warnings and precautions, assemb ly instr uctions , operating and maintenance procedures, par ts list and diagr am. K eep your in voice with this manual. Write the inv oice number on the inside of the front ...
-
Harbor Freight Tools 93974 - page 3
Page 3 SKU 93974 For technical questions, please call 1-800-444-3353 9. Maintain tools with care . K eep tools clean f or better and safer perf or mance. Follo w instructions for lubricating and changing accessor ies . Inspect tool cords and air hoses per iodically and, if damaged, ha ve them repaired b y an author ized technician. The handles must ...
-
Harbor Freight Tools 93974 - page 4
Page 4 SKU 93974 For technical questions, please call 1-800-444-3353 21. Read all of the information concerning coating pr oducts and cleaning solvents. Chlorinated solvents (e.g. 1-1-1 T richlorethylene and Meth ylene Chlor ide , also known as meth yl chlor ide) can chemically react with aluminum and ma y explode . Many paint spra yers contain alu ...
-
Harbor Freight Tools 93974 - page 5
Page 5 SKU 93974 For technical questions, please call 1-800-444-3353 Unpac king When unpacking, chec k to make sure the par ts listed on pages 14 and 16 are included. If any par ts are missing or brok en, please call Harbor F reight T ools at the number on the co v er of this manual as soon as possible . F or best ser vice y ou should incor porate ...
-
Harbor Freight Tools 93974 - page 6
Page 6 SKU 93974 For technical questions, please call 1-800-444-3353 Large Spra y Gun Small Spray Gun T rigger (14a) Air Cap (1a) Fluid Nozzle (4a) Fluid Control Knob (28a) Air Inlet (23a) Air Cap Set (1S) Cup (47) P atter n Control Knob (13) Fluid Control Knob (29) T rigger (38) Air Inlet (40) P aint Cup (34a) P atter n Control Knob (12a) Figure 1 ...
-
Harbor Freight Tools 93974 - page 7
Page 7 SKU 93974 For technical questions, please call 1-800-444-3353 Preparation Note: Proper paint material mixture helps to ensure less problems . Be sure to f ollow the manuf acturer’ s directions. Most materials will spra y readily if they are thinned properly . General tips for Preparation: 1. Mix and thin the paint/materials thoroughly acco ...
-
Harbor Freight Tools 93974 - page 8
Page 8 SKU 93974 For technical questions, please call 1-800-444-3353 F an Direction and P attern Adjustment F an Direction T o change the direction of the f an from hor iz ontal to ver tical, loosen the Loc k Ring and tur n the Air Cap (1 or 1a) 90 degrees . After the adjustment, tighten the Loc k Ring by hand. See FIGURE 2 below . Note: Alwa ys ma ...
-
Harbor Freight Tools 93974 - page 9
Page 9 SKU 93974 For technical questions, please call 1-800-444-3353 3. T urn the Fluid Control Knob (28a or 29) clockwise until it is fully closed. See FIGURE 1 on page 6. 4. After setting up a piece of scrap material, squeeze the T rigger in shor t bursts while tur ning the Fluid Control Knob countercloc kwise and obser ve the spra y patter ns un ...
-
Harbor Freight Tools 93974 - page 10
Page 10 SKU 93974 For technical questions, please call 1-800-444-3353 2. T o ensure y ou don’t allow paint to build up , star t moving the Spra y Gun bef ore you Squeeze the T rigger . When you are finished spr a ying, release the T r igger bef ore you stop moving the Spr a y Gun. Doing so will eliminate distinct ov er laps, producing a blended ( ...
-
Harbor Freight Tools 93974 - page 11
Page 11 SKU 93974 For technical questions, please call 1-800-444-3353 Operation P aint and Materials Preparation V erify with the paint or mater ials supplier the percentage of thinning required f or use with these Spra yers. T r y thinning a small amount and testing the spra y action. Thoroughly mix material before testing. Viscosity Viscosity is ...
-
Harbor Freight Tools 93974 - page 12
Page 12 SKU 93974 For technical questions, please call 1-800-444-3353 Maintenance SOL VENT SELECTION Alwa ys follo w the paint manufacturer’ s recommendations f or cleaning, solvent type, and disposing of used solvent. Latex P aints: Use warm, soapy w ater . IMPOR T ANT : Do not use mineral spirits on late x paints or the mixture will cong eal ma ...
-
Harbor Freight Tools 93974 - page 13
Page 13 SKU 93974 For technical questions, please call 1-800-444-3353 Disconnect from the air source. W arning! The Paint Cup and Spra y Gun may still hold air pressure, fire the Spray Gun towar d scrap material until all of the pressure is expended. 1 . Remov e the P aint Cup . 2 . P our residual paint into the paint container and seal it. 3 . P o ...
-
Harbor Freight Tools 93974 - page 14
Page 14 SKU 93974 For technical questions, please call 1-800-444-3353 NO TE : Some par ts are listed and shown for illustr ation pur poses only and are not a vailab le individually as replacement par ts. P ar ts List, Large Gun ...
-
Harbor Freight Tools 93974 - page 15
Page 15 SKU 93974 For technical questions, please call 1-800-444-3353 ...
-
Harbor Freight Tools 93974 - page 16
Page 16 SKU 93974 For technical questions, please call 1-800-444-3353 P ar ts List, Small Gun Diagram Note: When ordering par ts from this diagram add an “A” suffix. F or e xample Air Cap is par t number 1A. P atter n Control Knob Air Inlet Fluid Control Knob ...
-
Harbor Freight Tools 93974 - page 17
Page 17 SKU 93974 For technical questions, please call 1-800-444-3353 PLEASE READ THE FOLLO WING CAREFULL Y THE MANUF ACTURER AND/OR DISTRIB UT OR HAS PRO VIDED THE P AR TS DIAGRAM IN THIS MANU AL AS A REFERENCE T OOL ONL Y . NEITHER THE MANUF ACTURER NOR DISTRIBUT OR MAKES ANY REPRESENT A TION OR W ARRANTY OF ANY KIND T O THE BUYER THA T HE OR SHE ...
-
Harbor Freight Tools 93974 - page 18
Page 18 SKU 93974 For technical questions, please call 1-800-444-3353 T roub leshooting Spray P attern Diagnosis The P atter ns below resemble symptoms of spra y patter n prob lems. Please refer to the accompanying possib le problems if you are e xperiencing similar difficulties. The solution to each problem f ollows the prob lem in parentheses. Pr ...
-
Harbor Freight Tools 93974 - page 19
Page 19 SKU 93974 For technical questions, please call 1-800-444-3353 T roubleshooting (contin ued) 1. Low material le vel 2. Cup tipped too f ar 3. Clogged Air V ent 4. Loose fluid inlet connections 5. Dr y or loose fluid needle P acking Nut 6. Loose/damaged fluid tip/seat 1. No pressure at gun 2. Fluid control not open enough 3. Fluid too thick 1 ...
Harbor Freight Tools 93974についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもHarbor Freight Tools 93974の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHarbor Freight Tools 93974で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。