-
Tapco S8 - page 1
...
-
Tapco S8 - page 2
2 SAFETY INSTRUCTIONS 1. Read Instructions — All the safety and operation instructions should be read before this product is operated. 2. Retain Instructions — The safety and operating instructions should be kept for future reference. 3. Heed W arnings — All war nings on this product and in these operating instructions should be followed. 4. ...
-
Tapco S8 - page 3
Part No. 0008404 Rev. A 10/03 ©2003 LOUD T echnologies Inc. All Rights Reserved. 3 What me, read a manual? Before you begin, please make sure you read the Safety Instructions on page 2 and Getting Started on page 4. Y our new T APCO ® S•8 monitors are designed to set up quickly and operate easily. W e know it’s often seen as a sign of weaknes ...
-
Tapco S8 - page 4
4 Getting Started The following steps will help you set up your monitor speakers quickly. Follow these steps for all the S•8 studio monitors in your system. INITIAL SETTINGS: 1. Turn the INPUT LEVEL control on the rear panel all the way down. 2. Set the HIGH FREQ and LOW FREQ switches to “0 (NORMAL).” 3. Turn the POWER switch OFF . CONNECTION ...
-
Tapco S8 - page 5
BROUGHT TO YOU BY THE GROOVY FOLKS IN WOODINVILLE, WASHINGTON, USA MANUFACTURED IN CHINA • FABRIQUE AU CHINE ©2003 MACKIE DESIGNS, INC. 205323 C US R WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE P ARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONN ...
-
Tapco S8 - page 6
6 Here’s a quick look at all the features packed into the S•8 Studio Monitors: • Flat frequency response (±3 dB, 40 Hz to 20 kHz) • 1” silk dome tweeter , fully magnetically shielded • 8” polypropylene cone woofer , fully magnetically shielded • Convenient compact design, per fect for near- fi eld monitoring • Ported, bass refl ...
-
Tapco S8 - page 7
7 Hookup Diagrams Stereo Speak er Hookup Daisy-Chaining T w o Speakers Per Side Note: Use stereo 1/4” TRS plugs for the “Thru” connections. If you use mono 1/4” TS plugs, you will unbalance the XLR connections and suffer a drop in signal level of 6 dB. OFF XLR PHONO INPUTS SETTINGS INPUT LEVEL LOW FREQ FILTER HIGH FREQ FILTER 0 (NORMAL) – ...
-
Tapco S8 - page 8
BROUGHT TO YOU BY THE GROOVY FOLKS IN WOODINVILLE, WASHINGTON, USA MANUFACTURED IN CHINA • FABRIQUE AU CHINE ©2003 MACKIE DESIGNS, INC. 205323 C US R WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. DO NOT REMOVE COVER. NO USER SERVICEABLE PAR TS INSIDE. REFER SERVICING T O QUALIFIED PERSON ...
-
Tapco S8 - page 9
9 Get that sound level meter out. Decide what level you’re going to mix at and use the meter to help keep you mixing at that level. Y our ears will thank you, and your mixes will be better for it. 4. LOW FREQ Switch The LOW FREQ switch tailors the overall low-frequency response by +2 dB or +4 dB at 100 Hz and below. • For most applications, use ...
-
Tapco S8 - page 10
10 Protection Circuits There are several protection mechanisms designed into the S•8 to safeguard the loudspeakers and amplifi ers from inadvertent damage. C A UTION: The protection circuits are designed to protect the loudspeakers under reasonable and sensible conditions. Should you choose to ignore the warning signs (i.e., frequent Clip LED in ...
-
Tapco S8 - page 11
11 Appendix A: Service Infor mation No Sound • Is the power LED on the front panel illuminated? • Is the INPUT LEVEL control turned up? • Is the signal source turned up? Make sure the signal level from the mixing console (or whatever device immediately precedes the studio monitor) is high enough to produce sound. • If it’s a stereo pair , ...
-
Tapco S8 - page 12
12 Repair Service for T APCO products is available at our factory, located in sunny W oodinville, W ashington. Service for T APCO products living outside the United States can be obtained through local dealers or distributors. If your monitor needs service, follow these instructions: 1. Review the preceding troubleshooting suggestions. Please. 2. C ...
-
Tapco S8 - page 13
13 Appendix B: Connections XLR Connectors XLR connectors are used to make balanced connections to the S•8. They are wired as follows, according to standards specifi ed by the AES (Audio Engineering Society). XLR Balanced Wiring Pin 1 = Shield Pin 2 = Hot (+) Pin 3 = Cold (–) 1/4" TRS Phone Plugs and Jac ks “TRS” stands for T ip-Ring-S ...
-
Tapco S8 - page 14
14 Appendix C: S•8 Specifi cations Equalization Low Frequency EQ: +2 dB/+4 dB @ 100 Hz, shelving High Frequency EQ: ±2 dB @ 5 kHz, shelving AC Power R e qu i re m e n ts US: 120 V AC, 60 Hz Europe: 240 V AC, 50 Hz Korea (AC Power Select at 240 V): 220 V AC, 60 Hz Japan (AC Power Select at 120 V): 100 V AC, 50/60 Hz AC Connector: 2-pin IEC 250 V ...
-
Tapco S8 - page 15
15 T APCO LIMITED W ARRANTY A. LOUD T echnologies Inc. warrants all materials, workmanship and proper operation of this T APCO product for a period of one year from the original date of purchase. If any defects are found in the materials or workmanship, or if the product fails to function properly during the applicable warranty period, LOUD T echno ...
-
Tapco S8 - page 16
tapcogear .com ©2003 LOUD T echnologies Inc. All rights reserved.“T APCO” and “Mackie.” are registered trademarks of LOUD Technologies Inc. ...
Hai una domanda su Tapco S8?
Utilizza il modulo sottostante
Se non hai risolto il problema con Tapco S8 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Tapco S8 è probabile che voglia condividere il modo di risolverlo.