Italiano dropdown-ico

Manuale per l’uso Cisco Systems Cisco ONS 15454 SDH

34 pagine 0.4 mb
Scarica

Vai alla pagina of 34

Summary
  • Cisco Systems Cisco ONS 15454 SDH - page 1

    CHAPTER 4-1 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 4 Turn Up Node This chapter explains ho w to provision a single Cisco ONS 15454 SDH node and turn it up for service, including node name, date and time, timing references, network attrib utes such as IP address and default router , users and user security , and card protection group ...

  • Cisco Systems Cisco ONS 15454 SDH - page 2

    4-2 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D24 Verify Card Installation 8. NTP-D170 Create Protection Groups, page 4-26 —Complete this procedure, as needed, to set up 1:1, 1:N, 1+1, or Y -cable protection groups for ONS 15454 SDH electrical and optical cards. If you are turning up a D WDM or hybrid node, ...

  • Cisco Systems Cisco ONS 15454 SDH - page 3

    4-3 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D24 Verify Card Installation Step 6 V erify that electrical cards (E1-N-14, E1-42, E3-12, DS3I-N-12, or STM1E) are installed in the ONS 15454 SDH slots as designated by your installation plan. Step 7 If your site plan requires an Ethernet card, verify that the Eth ...

  • Cisco Systems Cisco ONS 15454 SDH - page 4

    4-4 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D30 Create Users and Assign Security NTP-D30 Create Users and Assign Security Step 1 Complete the “DLP-D60 Log into CTC” task on page 3-24 at the node where you want to create users. If you are already logged in, continue with Step 2. Note Y ou must log in as ...

  • Cisco Systems Cisco ONS 15454 SDH - page 5

    4-5 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D75 Create a New User—Multiple Nodes • Passw ord—T ype the user password. The password must be a minimum of six and a maximum of 20 alphanumeric (a-z, A-Z, 0-9) and special (+, #, %) characters, where at least two characters are nonalphabetic and at least on ...

  • Cisco Systems Cisco ONS 15454 SDH - page 6

    4-6 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D25 Set Up Name, Date, Time, and Contact Information • Security Lev el—Choose a security lev el for the user: RETRIEVE, MAINTEN ANCE, PR O VISIONING, or SUPER USER. Refer to the Cisco ONS 15454 SDH Reference Manual for information about the capabilities provid ...

  • Cisco Systems Cisco ONS 15454 SDH - page 7

    4-7 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D25 Set Up Name, Date, Time, and Contact Information Ti p Y ou can also position nodes manually on the network vie w map. Press Ctrl then drag and drop the node icon. T o create a logical network map for all ONS 15454 SDH users, complete the “NTP-D172 Create a L ...

  • Cisco Systems Cisco ONS 15454 SDH - page 8

    4-8 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D279 Set Power Monitor Thresholds Step 6 Revie w the node information. If you need to make corrections, repeat Steps 3 through 5 to enter the corrections. If the information is correct, continue with the “NTP-D279 Set Power Monitor Thresholds” procedure on pag ...

  • Cisco Systems Cisco ONS 15454 SDH - page 9

    4-9 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D169 Set Up CTC Network Access NTP-D169 Set Up CTC Network Access Step 1 Complete the “DLP-D60 Log into CTC” task on page 3-24 . If you are already logged in, continue with Step 2 . Step 2 Complete the “DLP-D249 Provision IP Settings” task on page 4-10 to ...

  • Cisco Systems Cisco ONS 15454 SDH - page 10

    4-10 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D249 Provision IP Settings DLP-D249 Provision IP Settings Caution All network changes should be approv ed by your network (or LAN) administrator . Step 1 If you are in network vie w , switch to node vie w by double-clicking the node you want to turn up on the net ...

  • Cisco Systems Cisco ONS 15454 SDH - page 11

    4-11 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D249 Provision IP Settings • MA C Address—( Display only . ) Displays the ONS 15454 SDH IEEE 802 MA C address. • Net/Subnet Mask Length—T ype the subnet mask length (decimal number representing the subnet mask length in bits) or click the arro ws to adjus ...

  • Cisco Systems Cisco ONS 15454 SDH - page 12

    4-12 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D249 Provision IP Settings Step 5 Click OK . The network vie w appears. The node icon appears in gray , during which time you cannot access the node. Step 6 Double-click the node icon when it becomes green. As necessary , complete the “DLP-D65 Create a Static R ...

  • Cisco Systems Cisco ONS 15454 SDH - page 13

    4-13 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D64 Set the IP Address, Default Router, and Network Mask Using the LCD Step 7 Return to your originating procedure (NTP). DLP-D64 Set the IP Address, Default Router, and Network Mask Using the LCD Note Y ou cannot perform this task if the LCD IP Display on the no ...

  • Cisco Systems Cisco ONS 15454 SDH - page 14

    4-14 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D64 Set the IP Address, Default Router, and Network Mask Using the LCD Figur e 4-2 Changing the IP A ddress Step 4 Push the Slot button to mo ve to the IP address or subnet mask digit you need to change. The selected digit f lashes. Ti p The Slot, Status, and Por ...

  • Cisco Systems Cisco ONS 15454 SDH - page 15

    4-15 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D65 Create a Static Route Step 10 Return to your originating procedure (NTP). DLP-D65 Create a Static Route Step 1 In node vie w , click the Provisioning > Network tabs. Step 2 Click the Static Routing tab . Click Create . Step 3 In the Create Static Route dia ...

  • Cisco Systems Cisco ONS 15454 SDH - page 16

    4-16 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D250 Set Up or Change Open Shortest Path First Protocol DLP-D250 Set Up or Change Open Shortest Path First Protocol Step 1 In node vie w , click the Provisioning > Network > OSPF tabs. Step 2 On the top left side of the OSPF pane, complete the following: ? ...

  • Cisco Systems Cisco ONS 15454 SDH - page 17

    4-17 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D250 Set Up or Change Open Shortest Path First Protocol Step 5 Provision the OSPF priority and interv al settings: The OSPF priority and interval def aults are ones most commonly used by OSPF routers. V erify that these defaults match the ones used by the OSPF ro ...

  • Cisco Systems Cisco ONS 15454 SDH - page 18

    4-18 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D251 Set Up or Change Routing Information Protocol • Retransmit Int (sec)—Sets the time that will elapse before a packet is resent. Fi ve seconds is the default. • Dead Int (sec)—Sets the number of seconds that will pass while an OSPF router’ s packets ...

  • Cisco Systems Cisco ONS 15454 SDH - page 19

    4-19 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D27 Set Up the ONS 15454 SDH for Firewall Access Step 6 If you want to complete an address summary , complete the follo wing steps. If not, continue with Step 7 . Complete the address summary only if the ONS 15454 SDH is a gate way NE with multiple external ONS 1 ...

  • Cisco Systems Cisco ONS 15454 SDH - page 20

    4-20 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D67 Provision the IIOP Listener Port on the ONS 15454 SDH Step 3 If the CTC computer resides behind a f irew all, complete the “DLP-D68 Provision the IIOP Listener Port on the CTC Computer” task on page 4-22 . Figure 4-6 shows a CTC computer and ONS 15454 SDH ...

  • Cisco Systems Cisco ONS 15454 SDH - page 21

    4-21 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D67 Provision the IIOP Listener Port on the ONS 15454 SDH Step 3 Click Apply . Step 4 When the Change Network Conf iguration message appears, click Y es . Both ONS 15454 SDH TCC2s reboot, one at a time. The reboot takes approximately 15 minutes. See T able 4-1 on ...

  • Cisco Systems Cisco ONS 15454 SDH - page 22

    4-22 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D68 Provision the IIOP Listener Port on the CTC Computer DLP-D68 Provision the IIOP Listener Port on the CTC Computer Step 1 In node vie w , from the Edit menu, choose Preferences . Step 2 In the Preferences dialog box, click the Firewall tab . Step 3 In the CTC ...

  • Cisco Systems Cisco ONS 15454 SDH - page 23

    4-23 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D69 Set Up External or Line Timing Step 1 Complete the “DLP-D60 Log into CTC” task on page 3-24 the ONS 15454 SDH node where you want to set up timing. If you are already logged in, continue with Step 2. Step 2 Complete the “DLP-D69 Set Up External or Line ...

  • Cisco Systems Cisco ONS 15454 SDH - page 24

    4-24 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D69 Set Up External or Line Timing • E1, 2.048 MHz, 64 KHz—Choose E1 , 2.048 MHz , or 64 KHz depending on the signal supported in your market. For e xample, 64 KHz is used in Japan. E1, 2.048 MHz, and 64 KHz are physical signal modes used to transmit the exte ...

  • Cisco Systems Cisco ONS 15454 SDH - page 25

    4-25 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D70 Set Up Internal Timing – T iming Mode set to Line—Y our options are the node’ s working OC-N cards (non-DWDM nodes), or OSC cards (D WDM nodes) and Internal Clock. Select the cards/ports that are directly or indirectly connected to the node wired to the ...

  • Cisco Systems Cisco ONS 15454 SDH - page 26

    4-26 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D170 Create Protection Groups • E1, 2.048 MHz, 64 KHz—Choose E1 , 2.048 MHz , or 64 KHz depending on the signal supported in your market. For e xample, 64 KHz is used in Japan. E1, 2.048 MHz, and 64 KHz are physical signal modes used to transmit the external ...

  • Cisco Systems Cisco ONS 15454 SDH - page 27

    4-27 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D170 Create Protection Groups T able 4-3 describes the protection types a vailable on the ONS 15454 SDH. Stop. Y ou ha ve completed this procedur e. T able 4-3 Card Pr otection T ypes T ype Cards Description and Installation Requirements 1:1 E1-N-14 DS3i-N-12 E3- ...

  • Cisco Systems Cisco ONS 15454 SDH - page 28

    4-28 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D71 Create a 1:1 Protection Group DLP-D71 Create a 1:1 Protection Group Step 1 V erify that the cards required for 1:1 protection are installed according to requirements specif ied in T able 4-3 . Step 2 In node vie w , click the Provisioning > Protection tabs ...

  • Cisco Systems Cisco ONS 15454 SDH - page 29

    4-29 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D72 Create a 1:N Protection Group DLP-D72 Create a 1:N Protection Group Step 1 V erify that the cards are installed according to 1:N requirements specif ied in T able 4-3 on page 4-27 . Step 2 Click the Pro visioning > Protection tabs. Step 3 In the Protection ...

  • Cisco Systems Cisco ONS 15454 SDH - page 30

    4-30 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D73 Create a 1+1 Protection Group DLP-D73 Create a 1+1 Protection Group Step 1 V erify that the cards are installed according to the 1+1 requirements specif ied in T able 4-3 on page 4-27 . Step 2 In node vie w , click the Provisioning > Protection tabs. Step ...

  • Cisco Systems Cisco ONS 15454 SDH - page 31

    4-31 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node DLP-D252 Create a Y-Cable Protection Group DLP-D252 Create a Y-Cable Protection Group Step 1 V erify that the transponder or muxponder cards are installed according to the Y -cable requirements specif ied in T able 4-3 on page 4-27 . Step 2 In node vie w , click the ...

  • Cisco Systems Cisco ONS 15454 SDH - page 32

    4-32 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D34 Set Up SNMP Step 5 From the A v ailable Ports list, choose the port that will be protected by the port you selected in Protect Ports. Click the top arrow b utton to move each port to the W orking Ports list. Step 6 Complete the remaining f ields: • Rev erti ...

  • Cisco Systems Cisco ONS 15454 SDH - page 33

    4-33 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D34 Set Up SNMP Note The community name is a form of authentication and access control. The community name assigned to the ONS 15454 SDH is case-sensitiv e and must match the community name of the network management system (NMS). • UDP Port—The default User D ...

  • Cisco Systems Cisco ONS 15454 SDH - page 34

    4-34 Cisco ONS 15454 SDH Procedure Guide, R4.6 January 2004 Chapter 4 Turn Up Node NTP-D34 Set Up SNMP ...

Fabbricante Cisco Systems Categoria Network Router

I documenti che otteniamo dal fabbricante del dispositivoCisco Systems Cisco ONS 15454 SDH possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Cisco Systems
- manuali per l’uso Cisco ONS 15454 SDH
- schede prodotto Cisco Systems
- opuscoli
- o etichette energetiche Cisco Systems Cisco ONS 15454 SDH
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Cisco Systems Cisco ONS 15454 SDH.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Cisco Systems Cisco ONS 15454 SDH, manuali di manutenzione, brevi manuali o manuali utente Cisco Systems Cisco ONS 15454 SDH. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Cisco Systems Cisco ONS 15454 SDH.

Manuali per l’uso simili

Manuale completo del dispositivo Cisco Systems Cisco ONS 15454 SDH, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Cisco Systems Cisco ONS 15454 SDH dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Cisco Systems Cisco ONS 15454 SDH.

Il manuale per l’uso completo Cisco Systems, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Cisco Systems Cisco ONS 15454 SDH - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Cisco Systems Cisco ONS 15454 SDH, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Cisco Systems Cisco ONS 15454 SDH che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Cisco Systems Cisco ONS 15454 SDH - che ci dovrebbe aiutare nei primi passi durante l'uso Cisco Systems Cisco ONS 15454 SDH
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Cisco Systems Cisco ONS 15454 SDH
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Cisco Systems Cisco ONS 15454 SDH in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Cisco Systems Cisco ONS 15454 SDH?

Utilizza il modulo sottostante

Se non hai risolto il problema con Cisco Systems Cisco ONS 15454 SDH con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Cisco Systems Cisco ONS 15454 SDH è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)