Italiano dropdown-ico

Manuale per l’uso Toyota 5613

32 pagine 3.01 mb
Scarica

Vai alla pagina of 32

Summary
  • Toyota 5613 - page 1

    3651 N Highway 89 • Chino V alley , AZ 86323 (928) 636-7080 • www .p-a-g .net T O Y O TA TA C O M A (AUT O. & MANUAL TRANS., 2 & 4WD, EXT . & CREW CAB, WITH O.E. TRAILER HITCH) 3” BODY LIFT INST ALLA TION INSTRUCTIONS 2005-2006 KIT# 5613 W ARNING Installation of a Performance Automotive Group body lift kit will change the vehicle? ...

  • Toyota 5613 - page 2

    2 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Before S t arting Inst allation 1. Carefully read all warning s and instructions com- pletely before beginning. 2. V erify all parts have been received in this kit by checking the part s list at th e end of this docume nt. 3. Only install this kit on the vehicle for which it is specified. If a ...

  • Toyota 5613 - page 3

    3 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Front of V ehicle 1. Front bumper a. Remove wiring harnesses from fog lights, if equipped. b. Remove two pop-up clips, two bolts and grill from core support. c. Remove seven pop-up clips from front bumper . Wiring Harness Fog Light Bolts Pop-up Clips Grill Pop-up Clips Front Bumper Fascia d. R ...

  • Toyota 5613 - page 4

    4 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 g. Remove six nuts and two front bumper brackets from frame ra ils . Engine Comp artment 1. 6 cyl. models: Loosen airb ox clamp, two clip s and remove airbox cover from engine. 2. 6 cyl. models: AC Line a. Remove bolt and AC line bracket from body . Nuts Front Bumper Brackets Clamp Clips Airbo ...

  • Toyota 5613 - page 5

    5 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 6. 4 cyl. models: Remove nut a nd AC line from pas- senger side AC line bracket. 7. 4 cyl. models: Remove lower AC line from two clip s and passenger side body . 8. Remove vent tubes from driver side body bracket. AC Line Bracket Nut AC Line Clip Passenger Side Body AC Line Bracket Vent Tubes ...

  • Toyota 5613 - page 6

    6 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 11 . Remove ABS wire harnesses from driver and p as- senger side brackets. 12. Remove wire harness and two clips from alternator bracket and driver side b ody bracket. ABS Wire Harnesse s Driver Side Passenger Side Battery Body Bracket Wire Harness Alternator Bracket 13. Radiator a. Remove nin ...

  • Toyota 5613 - page 7

    7 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 14. S teer ing Shaft a. S trap steer ing wheel to prevent accidental movement. b. Mark upper steering shaft in relation to cou pler and lower steering shaft. c. Remove coupler bolts, slide coupler up onto upper steering sha ft and disconnect steering shaft. d. Slide coupler down and off of upp ...

  • Toyota 5613 - page 8

    8 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 b. Remove dead pedal. c. Remove driver and passenger kick p anels. d. Pull driver and passenger carpet back from cor- ner and expose body mount bolt access cover . e. Remove driver and passenger body mount b olt access cover . NOTE Procedures may vary de pending on cab model for access to rear ...

  • Toyota 5613 - page 9

    9 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 e. Remove four bolts, and driver and passenger body mount access plates. f. Remove driver and passenger body mount b olt access covers. 4. Crew cab models: Rear interior trim panels a. Remove three headrests from seatbacks and fold seatbacks down. b. Remove three bolts and pop-clips from drive ...

  • Toyota 5613 - page 10

    10 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 3. Remove two bolts and brake line brackets from driver and passenger side frame rails. 4. Remove two bolts and parking brake cable brackets from crossmember . Driver Side Bolt & Brake Line Passenger Side Driver Side Passenger Side Parking Brake Cable Bolt & Bracket Parking Brake Cabl ...

  • Toyota 5613 - page 11

    1 1 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Rear of V eh icle 1. Fuel filler a. Remove fuel filler cap. b. Loosen two hose clamps and disconnect vent hose connector . c. Remove bolt and fuel filler from vehicle. W ARNING Use extreme caution when working nea r the fuel lines and the fuel tank. Clean up spilled fuel immediately . A spar ...

  • Toyota 5613 - page 12

    12 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Inst all Kit Cab 1. Lift cab a. Loosen, but DO NOT REMOVE, cab mounting bolts on driver side. b. Remove bolt, nut, and lower washer from each cab mount on passenger side. NOTE The number of ca b mounting bo lts may va ry with the length of the cab. Cab Mount (Core Support) Cab Mount (Mid Cab) ...

  • Toyota 5613 - page 13

    13 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 c. Install kit block (2” dia.) on upper bushings on front core support cab mount. d. Install kit blocks (3” dia.) on upper bu shings on each remaining cab mount. e. Lower cab onto kit blocks . f. Install factory front captive washer and a kit bolt (3/8” x 8”) on core su pport cab moun ...

  • Toyota 5613 - page 14

    14 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 3. Cab driver sid e a. Repeat previous steps on driver side of cab. b. Set cab-to-bed spacing according to previo us measurement. c. Remove front core support cab mo unt kit bolts (3/8” x 8”) and app ly a few drops of kit Loctite ® to threads. Install kit bolt s , factory captive wash- e ...

  • Toyota 5613 - page 15

    15 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 2. Remove bolt from each bed mount on passenger side. 3. Bed passenger side a. Remove ca ptive washer s from each factory be d mount bolt. b. Using a hydraulic jack and a wood block, slowly lift passenger side of bed a little more than 3”. W ARNING Use extreme caution when lifting the bed f ...

  • Toyota 5613 - page 16

    16 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 f. At rear bed mount, install kit bolt (M12-1.25 x 180mm) and factory captive w asher . DO NOT TIGHTEN. g. Repeat previous steps on driver side of bed. h. Set bed-to-cab spacing according to previo us measurement. i. Remove each kit bolt , one at a time, and apply a few drops of kit Loctite ? ...

  • Toyota 5613 - page 17

    17 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 b. Apply a small amount of kit Loctite ® onto threads of two factory bolts and install kit bracket (rear bump er , passenger) and kit bracket (bumper , spacer) to passenger side bumper with two factory b olts. DO NOT TIGHTEN. c. Repeat above step for driver side. d. Remove eight factory bolt ...

  • Toyota 5613 - page 18

    18 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 h. Install kit bracket (rear bumper , middle) onto O.E. trailer hitch with two ki t bolt s (1/2” x 1” ), four kit washers (1/2” SAE), and two kit nuts (1/ 2” stover). DO NOT TIGHTEN. i. Install license plate lights on rear bumper . j. Install rear bumper wiring har ness on frame, if p ...

  • Toyota 5613 - page 19

    19 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 d. Install kit extension (1/4” x 6” hose) b etween cut breather tube on fuel filler with two kit clamp s (#6 hose). DO NOT TIGHTEN. e. Install kit extension (5/8” x 6” hose) b etween cut vent tube on fuel filler with two kit clamp s (#10 hose). DO NOT TIGHTEN. f. Install kit extension ...

  • Toyota 5613 - page 20

    20 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Underside of V e hicle 1. Parking brake cable a. Install kit bracket (3” w/ stud) to driver side crossmember with factory bolt. b. Install driver side parking brake cable to kit bracket with kit nut (1/4” Nylock) and kit washer (1/4” SAE). c. Install kit bracket (3” w/ stud) to passen ...

  • Toyota 5613 - page 21

    21 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 3. Carefully bend brake lines and in stall bolt and brake line bracket to frame. 4. Brake lines a. Install kit bracket (2” Z-shaped) and factor y bolt to driver side frame. b. Install brake line bracket to kit bracket (2” Z- shaped) with kit bolt (1/4” x 1”), two kit washers (1/4” S ...

  • Toyota 5613 - page 22

    22 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 2. Crew cab models: Rear interior trim panels a. Install body mount access covers. b. Install passenger side rear panel onto cab with pop-clips and bolt. c. Install driver side rear panel onto cab with pop- clips and three bolts. d. Return seatbacks to upright positio n and install three head ...

  • Toyota 5613 - page 23

    23 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 e. Install driver and p a ss enger door sill plates. 4. Manual transmission a. Remove plastic cap from end of shift lever . b. Mark alignment and cut lines on shifter lever below bend. c. Cut shifter lever along marked cut line. Door Sill Plate Shift Lever Plastic Cap Shift Lever Cut Line Ali ...

  • Toyota 5613 - page 24

    24 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Engine Comp artment 1. S teer ing shaft a. Install upper steering sh aft into kit extension (steering), ensurin g marks on upper and lower steering shaft are aligned. b. Position kit extension (steering) into stee ring coupler . Ensu re marks on upper and lower steering shaft are aligned. c. ...

  • Toyota 5613 - page 25

    25 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 c. Install radiator and fo ur kit brackets to core sup- port with four kit washers (1/4” SAE) and four kit nut s (1/4” Nylock). DO NOT TIGHTEN. d. Assemble kit plates (radiator block off) with kit bolt (1/4” x 1”), two kit washers (1/4” SAE) and kit nut (1/4” Nylock). DO NOT TIGHT ...

  • Toyota 5613 - page 26

    26 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 3. Install wire harness and clips to alternator bracket and driver side body bracket. Adjust clips if neces- sary . 4. Install vent hoses to driver side body bracket with kit tie (zip). Battery Body Bracket Wire Harness Alternator Bracket Kit Tie (Zip) Bracket Vent Hoses 5. Install driver and ...

  • Toyota 5613 - page 27

    27 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 8. 6 cyl. models: Power st eering re servoi r a. Remove reservoir cap an d drain contents into drain p an. b. Remove two clamps and power steering lines from reservo ir . c. Mark power st eering lines . d. Cut power steering lines along cut marks. e. Drain any remaining fluid from power steer ...

  • Toyota 5613 - page 28

    28 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 9. 4 cyl. models: Power steering requires no modifica- tion. 10. 6 cyl. models: AC Line a. Install rubber isolator to body . b. Install AC line and cla mp onto rubber isolator with nut. 1 1. 4 cyl. models: AC Line a. Install kit brack et (3” Z-shaped) to passenger side AC line bracket with ...

  • Toyota 5613 - page 29

    29 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 b. Apply a small amount of kit Loc tite ® to six kit bolts (3/8” x 1”) and install front bumper to kit brackets (front bumper) with twelve kit washers (3/8” USS) and six kit nut s (3/8” Nylock). c. Install front bu mp er c over t o veh icl e wit h six fa c- tory screws. Kit Bolts (3/ ...

  • Toyota 5613 - page 30

    30 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Af ter Completing Inst allation Inside Cab 1. Install airbag fuse and fu se block cover . Engine Comp artment 1. Connect both battery cables . Connect positive cable first, then negative cable. Fuse Cover Fuse Location May Vary Airbag Fuse Negative Cable (B la ck ) Positive Cable (R e d) Misc ...

  • Toyota 5613 - page 31

    31 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Accessories The following accessories are also available: Kit # 6337: Gap Guards ...

  • Toyota 5613 - page 32

    32 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Kit Part s List Qty . Description NOTE Depending on th e vehicle configuration (auto matic or manual transmission, 2WD or 4W D, cab length, bed length, etc.), some part s may not be used. 8 Block (2" x 3" spac er) 4 Block (3" x 3" spac er) 1 Bracket (f ront bum per, driver ...

Fabbricante Toyota Categoria Automobile Accessories

I documenti che otteniamo dal fabbricante del dispositivoToyota 5613 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Toyota
- manuali per l’uso 5613
- schede prodotto Toyota
- opuscoli
- o etichette energetiche Toyota 5613
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Toyota 5613.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Toyota 5613, manuali di manutenzione, brevi manuali o manuali utente Toyota 5613. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Toyota 5613.

Manuali per l’uso simili

Manuale completo del dispositivo Toyota 5613, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Toyota 5613 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Toyota 5613.

Il manuale per l’uso completo Toyota, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Toyota 5613 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Toyota 5613, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Toyota 5613 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Toyota 5613 - che ci dovrebbe aiutare nei primi passi durante l'uso Toyota 5613
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Toyota 5613
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Toyota 5613 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Toyota 5613?

Utilizza il modulo sottostante

Se non hai risolto il problema con Toyota 5613 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Toyota 5613 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (1)

Бен

Как удалить кусочек листка,застрявшего в принтере JC68 -j6902690001 если recjxtr торчит из зажима только на 2-3 мм.