Toyota 5613の取扱説明書

32ページ 3.01 mb
ダウンロード

ページに移動 of 32

Summary
  • Toyota 5613 - page 1

    3651 N Highway 89 • Chino V alley , AZ 86323 (928) 636-7080 • www .p-a-g .net T O Y O TA TA C O M A (AUT O. & MANUAL TRANS., 2 & 4WD, EXT . & CREW CAB, WITH O.E. TRAILER HITCH) 3” BODY LIFT INST ALLA TION INSTRUCTIONS 2005-2006 KIT# 5613 W ARNING Installation of a Performance Automotive Group body lift kit will change the vehicle? ...

  • Toyota 5613 - page 2

    2 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Before S t arting Inst allation 1. Carefully read all warning s and instructions com- pletely before beginning. 2. V erify all parts have been received in this kit by checking the part s list at th e end of this docume nt. 3. Only install this kit on the vehicle for which it is specified. If a ...

  • Toyota 5613 - page 3

    3 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Front of V ehicle 1. Front bumper a. Remove wiring harnesses from fog lights, if equipped. b. Remove two pop-up clips, two bolts and grill from core support. c. Remove seven pop-up clips from front bumper . Wiring Harness Fog Light Bolts Pop-up Clips Grill Pop-up Clips Front Bumper Fascia d. R ...

  • Toyota 5613 - page 4

    4 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 g. Remove six nuts and two front bumper brackets from frame ra ils . Engine Comp artment 1. 6 cyl. models: Loosen airb ox clamp, two clip s and remove airbox cover from engine. 2. 6 cyl. models: AC Line a. Remove bolt and AC line bracket from body . Nuts Front Bumper Brackets Clamp Clips Airbo ...

  • Toyota 5613 - page 5

    5 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 6. 4 cyl. models: Remove nut a nd AC line from pas- senger side AC line bracket. 7. 4 cyl. models: Remove lower AC line from two clip s and passenger side body . 8. Remove vent tubes from driver side body bracket. AC Line Bracket Nut AC Line Clip Passenger Side Body AC Line Bracket Vent Tubes ...

  • Toyota 5613 - page 6

    6 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 11 . Remove ABS wire harnesses from driver and p as- senger side brackets. 12. Remove wire harness and two clips from alternator bracket and driver side b ody bracket. ABS Wire Harnesse s Driver Side Passenger Side Battery Body Bracket Wire Harness Alternator Bracket 13. Radiator a. Remove nin ...

  • Toyota 5613 - page 7

    7 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 14. S teer ing Shaft a. S trap steer ing wheel to prevent accidental movement. b. Mark upper steering shaft in relation to cou pler and lower steering shaft. c. Remove coupler bolts, slide coupler up onto upper steering sha ft and disconnect steering shaft. d. Slide coupler down and off of upp ...

  • Toyota 5613 - page 8

    8 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 b. Remove dead pedal. c. Remove driver and passenger kick p anels. d. Pull driver and passenger carpet back from cor- ner and expose body mount bolt access cover . e. Remove driver and passenger body mount b olt access cover . NOTE Procedures may vary de pending on cab model for access to rear ...

  • Toyota 5613 - page 9

    9 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 e. Remove four bolts, and driver and passenger body mount access plates. f. Remove driver and passenger body mount b olt access covers. 4. Crew cab models: Rear interior trim panels a. Remove three headrests from seatbacks and fold seatbacks down. b. Remove three bolts and pop-clips from drive ...

  • Toyota 5613 - page 10

    10 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 3. Remove two bolts and brake line brackets from driver and passenger side frame rails. 4. Remove two bolts and parking brake cable brackets from crossmember . Driver Side Bolt & Brake Line Passenger Side Driver Side Passenger Side Parking Brake Cable Bolt & Bracket Parking Brake Cabl ...

  • Toyota 5613 - page 11

    1 1 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Rear of V eh icle 1. Fuel filler a. Remove fuel filler cap. b. Loosen two hose clamps and disconnect vent hose connector . c. Remove bolt and fuel filler from vehicle. W ARNING Use extreme caution when working nea r the fuel lines and the fuel tank. Clean up spilled fuel immediately . A spar ...

  • Toyota 5613 - page 12

    12 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Inst all Kit Cab 1. Lift cab a. Loosen, but DO NOT REMOVE, cab mounting bolts on driver side. b. Remove bolt, nut, and lower washer from each cab mount on passenger side. NOTE The number of ca b mounting bo lts may va ry with the length of the cab. Cab Mount (Core Support) Cab Mount (Mid Cab) ...

  • Toyota 5613 - page 13

    13 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 c. Install kit block (2” dia.) on upper bushings on front core support cab mount. d. Install kit blocks (3” dia.) on upper bu shings on each remaining cab mount. e. Lower cab onto kit blocks . f. Install factory front captive washer and a kit bolt (3/8” x 8”) on core su pport cab moun ...

  • Toyota 5613 - page 14

    14 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 3. Cab driver sid e a. Repeat previous steps on driver side of cab. b. Set cab-to-bed spacing according to previo us measurement. c. Remove front core support cab mo unt kit bolts (3/8” x 8”) and app ly a few drops of kit Loctite ® to threads. Install kit bolt s , factory captive wash- e ...

  • Toyota 5613 - page 15

    15 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 2. Remove bolt from each bed mount on passenger side. 3. Bed passenger side a. Remove ca ptive washer s from each factory be d mount bolt. b. Using a hydraulic jack and a wood block, slowly lift passenger side of bed a little more than 3”. W ARNING Use extreme caution when lifting the bed f ...

  • Toyota 5613 - page 16

    16 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 f. At rear bed mount, install kit bolt (M12-1.25 x 180mm) and factory captive w asher . DO NOT TIGHTEN. g. Repeat previous steps on driver side of bed. h. Set bed-to-cab spacing according to previo us measurement. i. Remove each kit bolt , one at a time, and apply a few drops of kit Loctite ? ...

  • Toyota 5613 - page 17

    17 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 b. Apply a small amount of kit Loctite ® onto threads of two factory bolts and install kit bracket (rear bump er , passenger) and kit bracket (bumper , spacer) to passenger side bumper with two factory b olts. DO NOT TIGHTEN. c. Repeat above step for driver side. d. Remove eight factory bolt ...

  • Toyota 5613 - page 18

    18 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 h. Install kit bracket (rear bumper , middle) onto O.E. trailer hitch with two ki t bolt s (1/2” x 1” ), four kit washers (1/2” SAE), and two kit nuts (1/ 2” stover). DO NOT TIGHTEN. i. Install license plate lights on rear bumper . j. Install rear bumper wiring har ness on frame, if p ...

  • Toyota 5613 - page 19

    19 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 d. Install kit extension (1/4” x 6” hose) b etween cut breather tube on fuel filler with two kit clamp s (#6 hose). DO NOT TIGHTEN. e. Install kit extension (5/8” x 6” hose) b etween cut vent tube on fuel filler with two kit clamp s (#10 hose). DO NOT TIGHTEN. f. Install kit extension ...

  • Toyota 5613 - page 20

    20 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Underside of V e hicle 1. Parking brake cable a. Install kit bracket (3” w/ stud) to driver side crossmember with factory bolt. b. Install driver side parking brake cable to kit bracket with kit nut (1/4” Nylock) and kit washer (1/4” SAE). c. Install kit bracket (3” w/ stud) to passen ...

  • Toyota 5613 - page 21

    21 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 3. Carefully bend brake lines and in stall bolt and brake line bracket to frame. 4. Brake lines a. Install kit bracket (2” Z-shaped) and factor y bolt to driver side frame. b. Install brake line bracket to kit bracket (2” Z- shaped) with kit bolt (1/4” x 1”), two kit washers (1/4” S ...

  • Toyota 5613 - page 22

    22 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 2. Crew cab models: Rear interior trim panels a. Install body mount access covers. b. Install passenger side rear panel onto cab with pop-clips and bolt. c. Install driver side rear panel onto cab with pop- clips and three bolts. d. Return seatbacks to upright positio n and install three head ...

  • Toyota 5613 - page 23

    23 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 e. Install driver and p a ss enger door sill plates. 4. Manual transmission a. Remove plastic cap from end of shift lever . b. Mark alignment and cut lines on shifter lever below bend. c. Cut shifter lever along marked cut line. Door Sill Plate Shift Lever Plastic Cap Shift Lever Cut Line Ali ...

  • Toyota 5613 - page 24

    24 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Engine Comp artment 1. S teer ing shaft a. Install upper steering sh aft into kit extension (steering), ensurin g marks on upper and lower steering shaft are aligned. b. Position kit extension (steering) into stee ring coupler . Ensu re marks on upper and lower steering shaft are aligned. c. ...

  • Toyota 5613 - page 25

    25 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 c. Install radiator and fo ur kit brackets to core sup- port with four kit washers (1/4” SAE) and four kit nut s (1/4” Nylock). DO NOT TIGHTEN. d. Assemble kit plates (radiator block off) with kit bolt (1/4” x 1”), two kit washers (1/4” SAE) and kit nut (1/4” Nylock). DO NOT TIGHT ...

  • Toyota 5613 - page 26

    26 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 3. Install wire harness and clips to alternator bracket and driver side body bracket. Adjust clips if neces- sary . 4. Install vent hoses to driver side body bracket with kit tie (zip). Battery Body Bracket Wire Harness Alternator Bracket Kit Tie (Zip) Bracket Vent Hoses 5. Install driver and ...

  • Toyota 5613 - page 27

    27 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 8. 6 cyl. models: Power st eering re servoi r a. Remove reservoir cap an d drain contents into drain p an. b. Remove two clamps and power steering lines from reservo ir . c. Mark power st eering lines . d. Cut power steering lines along cut marks. e. Drain any remaining fluid from power steer ...

  • Toyota 5613 - page 28

    28 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 9. 4 cyl. models: Power steering requires no modifica- tion. 10. 6 cyl. models: AC Line a. Install rubber isolator to body . b. Install AC line and cla mp onto rubber isolator with nut. 1 1. 4 cyl. models: AC Line a. Install kit brack et (3” Z-shaped) to passenger side AC line bracket with ...

  • Toyota 5613 - page 29

    29 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 b. Apply a small amount of kit Loc tite ® to six kit bolts (3/8” x 1”) and install front bumper to kit brackets (front bumper) with twelve kit washers (3/8” USS) and six kit nut s (3/8” Nylock). c. Install front bu mp er c over t o veh icl e wit h six fa c- tory screws. Kit Bolts (3/ ...

  • Toyota 5613 - page 30

    30 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Af ter Completing Inst allation Inside Cab 1. Install airbag fuse and fu se block cover . Engine Comp artment 1. Connect both battery cables . Connect positive cable first, then negative cable. Fuse Cover Fuse Location May Vary Airbag Fuse Negative Cable (B la ck ) Positive Cable (R e d) Misc ...

  • Toyota 5613 - page 31

    31 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Accessories The following accessories are also available: Kit # 6337: Gap Guards ...

  • Toyota 5613 - page 32

    32 ‘05 - ‘06 T acoma (W/ O.E. Hitch) - 3” Kit 5613 Kit Part s List Qty . Description NOTE Depending on th e vehicle configuration (auto matic or manual transmission, 2WD or 4W D, cab length, bed length, etc.), some part s may not be used. 8 Block (2" x 3" spac er) 4 Block (3" x 3" spac er) 1 Bracket (f ront bum per, driver ...

メーカー Toyota カテゴリー Automobile Accessories

Toyota 5613のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 5613の取扱説明書
- Toyotaの製品カード
- パンフレット
- またはToyota 5613の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Toyota 5613の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Toyota 5613の取り付け説明書、サービスマニュアル、簡易説明書、またはToyota 5613のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Toyota 5613の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Toyota 5613デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがToyota 5613を使用するのを助ける技術的文書のことです。説明書は通常、全てのToyota 5613ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Toyotaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Toyota 5613の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははToyota 5613の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Toyota 5613に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Toyota 5613デバイスの基本機能を使うにあたってのヒント。 Toyota 5613のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Toyota 5613に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるToyota 5613のメーカー/サービスへの連絡先に関する情報。

Toyota 5613についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもToyota 5613の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがToyota 5613で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (1)

Бен

Как удалить кусочек листка,застрявшего в принтере JC68 -j6902690001 если recjxtr торчит из зажима только на 2-3 мм.