Italiano dropdown-ico

Manuale per l’uso Measurement Specialties CIO-SSH16

32 pagine 0.69 mb
Scarica

Vai alla pagina of 32

Summary
  • Measurement Specialties CIO-SSH16 - page 1

    CIO-SSH16 USER’S MANUAL Revision 3 October, 2000 ...

  • Measurement Specialties CIO-SSH16 - page 2

    MEGA -FIFO, the CIO pre fix to da ta ac quisition board m odel num bers, the PCM pre fix to data acquisition boa rd model num bers, PCM-DA S08, PCM-D24C3, PCM-DAC02, PCM-COM422, PCM-COM485, PCM-DMM, PCM-DA S16D/12, PCM-DA S16S/12, PCM-DA S16D/16, PCM-DAS16S/16, PCI-DA S6402/16, Universal L ibrary , Insta Cal, Harsh Enviro nment Warranty and M easur ...

  • Measurement Specialties CIO-SSH16 - page 3

    23 6.9 NOISE ...................................................... 22 6.8 CURRENT LOOP (4-20 mA) .................................... 22 6.7 ENGINEERING UNITS ........................................ 21 6.6 A/D RESOLUTION & ENGINEERING UNITS ...................... 20 6.5 LOW PASS FILTERS .......................................... 20 6.4 GROUND ...

  • Measurement Specialties CIO-SSH16 - page 4

    This page is blank. ...

  • Measurement Specialties CIO-SSH16 - page 5

    1.0 SOFTWARE INSTALLATION Before installing the board, install and run Ins ta Cal. This package is the installation, calibration and test utility included with y our board . Insta Cal will guide you through switch and jum per settings for your board. Detailed information regarding these settings can be found below. Refer to the Extended Softw are I ...

  • Measurement Specialties CIO-SSH16 - page 6

    There are two cables used w ith CIO-SSH16; a signal cable an d a power cable. The power cable (C-PCPOWER-10) is supplied with the CIO-SSH16. The power cable is black w ith tw o white MOLEX con nectors. One end mates w ith the J3 connector on th e SSH16 and the other m ates with an y one of the available PC power expansion plugs inside the PC. The s ...

  • Measurement Specialties CIO-SSH16 - page 7

    The SSH16 requ ires 1 A mp of +5 vol t pow er. You m ay su pply t his pow er from the PC , as we recomm end, using the cable supplied, or you may use an alternate power supply. Figure 4-2. Power Connector Cauti on on usin g alter nate power s upplies : The analog interf ace from the SSH-16 to the CIO-DAS16 is a single ended voltage signal connectio ...

  • Measurement Specialties CIO-SSH16 - page 8

    connected. The nomenclatu re on the CIO-SSH16 corresponds to CIO-DAS16 sig nals. 2.4 ANALOG INPUT BOARD SETUP The analog i nput board mu st be confi gured for s ingle- ended inpu t. If the board y ou are usin g w ith the C IO-SSH16 su pports bot h 8 chan nel dif ferenti al and 16 chann el single-ended configurations, set the board to 16 channels si ...

  • Measurement Specialties CIO-SSH16 - page 9

    3.0 SIGNAL CONNECTION 3.1 CONNECTOR DIAGRAM The CIO-SSH16 in puts are screw terminals w hich w ill accept 12-22 AWG wire. Each chann el has a screw term inal for signal high, signal low and ground. 3.2 ANALOG INPUTS Analog inputs to the CIO-SSH16 may be connected in tw o different configurations. In order of complexity, these are Floating Different ...

  • Measurement Specialties CIO-SSH16 - page 10

    A floating differ ential hookup is handy when the signal source is floa ting w ith respec t to ground, such as a ba ttery, 4-20 mA transm itter or thermocouple and the lead lengths are long or subject to EMI interference. The floating differential input will reject up to 10V of EMI energy on the signal wires. WARNING! Verify that the signal source ...

  • Measurement Specialties CIO-SSH16 - page 11

    A laboratory instrum ent with its ow n wall plug. There are sometim es differences in wall GND between outlets. 7 ...

  • Measurement Specialties CIO-SSH16 - page 12

    4.0 ARCHITECTURE There are two ty pes of functional elem ents on the CIO-SSH16; differential am plifiers and a sam ple & hold chips (LF398). To geth er they provide diff erential inpu t and amplification for up to 16 channels of simultaneous sampling signal conditioning. This section contains information on the following subjects: Amplification ...

  • Measurement Specialties CIO-SSH16 - page 13

    level signal to the analog input boards single ended inputs, reducing the im pact of EMI or RFI alon g the sig nal cable betw een the CIO- SSH16 and the analog inpu t board. 4.3 CIO-SSH16 vs. PROGRAMMABLE GAIN A/D BOARDS Having a dedicated differen tial amplif ier for every ch annel produ ces flexible and powerful data acquisition c apability. Data ...

  • Measurement Specialties CIO-SSH16 - page 14

    Figure 4-5. Input Range Optimization During post-processing analysis, the range w hich provid ed the best reso lution at any point in time is instantly available. The cost of a CIO-DA S16 and CIO-SSH16 is less th an the cost of an A /D board w ith a channel gain queue and far less than alternative sim ultaneous sample & hold schemes. It certain ...

  • Measurement Specialties CIO-SSH16 - page 15

    Figure 4-6. Input Amplifiers with Sample and Hold Chips SSH OUT is synchronized to the analog inpu t boards S&H chip and the channel select MUX. When the analog input board sam ples chann el 0, each of the LF398s on the CIO-S SH16 also sam ples th e sign al on its input. Each of th e LF398s t hen sw itch es to HOLD m ode and the analog inpu t b ...

  • Measurement Specialties CIO-SSH16 - page 16

    Figure 4-7. Sample and Hold Timing Diagram Note that Channel 0 of the CIO-SSH16 does not have an LF398 sample and hold chip. That is because there is one sam ple and hold on the analog input board and it serv es as the S&H chip for CIO- SSH16’s chann el 0. When the S&H on th e A/D board is sampling the signal on channel 0, the S&Hs on ...

  • Measurement Specialties CIO-SSH16 - page 17

    To calculate the effect of the droop rate on the accuracy of y our measu rement, th e range of the signal, the resolution of the A/D converter and the time between HOL D and A/D acquisition are needed. Here is an example. RANGE CALCULATION Signal Range ±50 millivolts Gain 100 Amplifier Output ±5 Volts At full scale RESOLUTION CALCULATION A/D reso ...

  • Measurement Specialties CIO-SSH16 - page 18

    5.0 SPECIFICATIONS Typical for 25°C unless otherwise specified. Power consumption +5V 1.0A typical, 1.25A max Analog input section Input amplifier type INA110 Number of channels 16 differential Input range ±10V Gains X1, X10, X100, X110, X200, X210, X300, X310, X500, X510, X600, X610, X700, X710, X800, X810 Gain error Gain = 1 0.02% max, 0.002% t ...

  • Measurement Specialties CIO-SSH16 - page 19

    Sample / hold section Sample / hold type LF398 Aperture time 250 ns max, 150 ns typical Aperture uncertainty 50 ns typical Acquisition time 10 µ s m ax Temperature coefficient 4 ppm/°C Droop rate ±100µV/ms RMS Noise (10 kHz to 100 kHz) 10µV Current Drive ±5 mA Output coupling DC Output impedance 0.1 Ohms max Miscellaneous TTL high level for s ...

  • Measurement Specialties CIO-SSH16 - page 20

    6.0 ANALOG ELECTRONICS This short intro duction to the analog electronics most often needed by data acquisition board users describes the follo wing: Voltage dividers. Differential vs. Single Ended Inputs. Isolation vs. Common Mode Range Low pass filters for analog and digital inputs. A/D Resolution Conversion to Engineering units. 4-20 mA inputs N ...

  • Measurement Specialties CIO-SSH16 - page 21

    Figure 6-1. Voltage Divider The object in usin g a voltag e divi der is to ch oose tw o resistors wit h th e proper proportions rel ative to th e full scale of th e analog or digital input an d the m axim um signal voltage. Dropping t he voltag e proportionall y is often called atten uation. The formu la for attenuation is: For a give n attenuatio ...

  • Measurement Specialties CIO-SSH16 - page 22

    IMPORTANT NOTE: The resistors, R1 and R2, are going to dissipate all the power in the divider circuit accordin g to the equation Cu rrent = Voltage / Resistance. The high er the valu e of the resistance (R1 + R2) the less power dissipated by th e divider circuit. Here is a simple rule: For Attenuation of 5:1 or less, no resistor should be less than ...

  • Measurement Specialties CIO-SSH16 - page 23

    A sing le ended input has no com mon m ode range because there is only one LOW wire, which is assumed to be at the same level at the signal and at the A/D board. Figure 6-3. Single-Ended Input The maximum difference which may be rejected is the CMR. For exam ple, the CIO- SSH16 has a common mode plu s sign al range of 11.5 volts, common mode not to ...

  • Measurement Specialties CIO-SSH16 - page 24

    the designer of the board (or other EE) would be able to tran slate that into a system s specification, most A/D board owners are confused or mislead by such specs. 6.3 COMMON MISUNDERSTANDINGS The CMR specification of a differential input is often confused with an isolation specification, which it is not. CMR o f 10 volts is not the same as 10 vol ...

  • Measurement Specialties CIO-SSH16 - page 25

    associated with line voltage (60 Hz) would be filtered out but a signal of 25 Hz would be allowed to pass. Also, in a digital circuit, a low pass filter is often used to filter an input from a switch. Figure 6-5. Low pass Filter A low pass filter m ay be constructed from one resistor (R) and one capacitor (C). The cut off frequency is determined ac ...

  • Measurement Specialties CIO-SSH16 - page 26

    Resolution is a measure of the ability to differentiate betw een one voltage and ano ther. Obviou sly , the m ore bits of resolut ion (13 bits = 8192 coun ts) th e more div ision s of full scale. The m ore divisio ns of f ull scale, the higher the resolution of the measurement. 6.7 ENGINEERING UNITS When a program uses an A/D board to acquire d ata ...

  • Measurement Specialties CIO-SSH16 - page 27

    For example, if the CIO-DAS16 board is set up to read 0 to 5 volts, then: 5 volts / 0.02 Amps = 250 Ohm shunt resistor. So a full 20 mA will register 5 volts and 4 mA will register 1 volt. To hook up the CIO-DA S16 analog inputs t o a 4-20 mA transducer or sign al source, place the shunt resistor across the plus and m inus terminals or signal w ire ...

  • Measurement Specialties CIO-SSH16 - page 28

    specify the conditions under which the specification was made. That means the PC, the PC's power supply and the connection to the front end. Put som e very good com ponents on a circuit board and place th at board in a PC and the system w ill be less accurate than the individual com ponents. Some 12-bit A/D boards with the sam e components as ...

  • Measurement Specialties CIO-SSH16 - page 29

    6.9.4 SMOOTHING DATA It is not alw ays possible to eliminate all noise, especially w ith very low level sensors, but noi se looks terribl e wh en plotted an d can raise doubts abou t otherw ise ex cellent data. There are two simple ways to eliminate noise from the data: 1. Apply a m oving average to the data if you w ant to retain the same apparent ...

  • Measurement Specialties CIO-SSH16 - page 30

    For your notes. 26 ...

  • Measurement Specialties CIO-SSH16 - page 31

    EC Declaration of Conformity We, Measurement Computing Corp. , declare under sole responsibility that the product: Description Part Number CIO-SSH16 to which this declaration relates, meets the essential requirements, is in conformity with , and CE m arking h as been applied according to the relevan t EC Directives listed belo w using the re levant ...

  • Measurement Specialties CIO-SSH16 - page 32

    Measurement Computing Corporation 16 Commerce Boulevard, Middleboro, Massachusetts 02346 (508) 946-5100 Fax: (508) 946-9500 E-mail: info@measurementcomputing.com www. measurementcomputing.com ...

Fabbricante Measurement Specialties Categoria Computer Hardware

I documenti che otteniamo dal fabbricante del dispositivoMeasurement Specialties CIO-SSH16 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Measurement Specialties
- manuali per l’uso CIO-SSH16
- schede prodotto Measurement Specialties
- opuscoli
- o etichette energetiche Measurement Specialties CIO-SSH16
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Measurement Specialties CIO-SSH16.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Measurement Specialties CIO-SSH16, manuali di manutenzione, brevi manuali o manuali utente Measurement Specialties CIO-SSH16. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Measurement Specialties CIO-SSH16.

Manuali per l’uso simili

Manuale completo del dispositivo Measurement Specialties CIO-SSH16, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Measurement Specialties CIO-SSH16 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Measurement Specialties CIO-SSH16.

Il manuale per l’uso completo Measurement Specialties, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Measurement Specialties CIO-SSH16 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Measurement Specialties CIO-SSH16, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Measurement Specialties CIO-SSH16 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Measurement Specialties CIO-SSH16 - che ci dovrebbe aiutare nei primi passi durante l'uso Measurement Specialties CIO-SSH16
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Measurement Specialties CIO-SSH16
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Measurement Specialties CIO-SSH16 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Measurement Specialties CIO-SSH16?

Utilizza il modulo sottostante

Se non hai risolto il problema con Measurement Specialties CIO-SSH16 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Measurement Specialties CIO-SSH16 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Captcha
Nuova immagine

Commenti (0)