Manuale per l’uso KTI Networks 10BASE-T

17 pagine 0.07 mb
Scarica

Vai alla pagina of 17

Summary
  • KTI Networks 10BASE-T - page 1

    Installation Guide 10BASE-T/100BASE-TX 8-Port Dual-Speed Hub Model: KF-8D DOC.980329-KF8D-K P/N: 750-0109-001 ...

  • KTI Networks 10BASE-T - page 2

    Ó 1998 KTI Networks Inc. All rights reserved. No part of this docu- mentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time t ...

  • KTI Networks 10BASE-T - page 3

    8-Port Dual-Speed Ethernet/Fast Ethernet Hub Installation Guide DOC.980330-KF8D-NK P/N: 750-0109-002 ...

  • KTI Networks 10BASE-T - page 4

    The information contained in this document is subject to change without prior no- tice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are d ...

  • KTI Networks 10BASE-T - page 5

    T able of Contents Chapter 1 Introduction Introduction ............................................................................... 1 Features ................................................................................... 2 Dual-speed Hub T echnology .................................................... 3 Chapter 2 Installation Unpacking ... ...

  • KTI Networks 10BASE-T - page 6

    1. Introduction KF-8D dual-speed Fast Ethernet/Ethernet hub is designed to allow easy and flexible migration from 10Mbps Ethernet to 100Mbps Fast Ethernet. The hub complies with IEEE 802.3 and IEEE 802.3u repeater specifications and supports 10Mbps and 100Mbps con- nectivity over UTP cabling in the same hub. The hub provides 8 dual-speed TP ports. ...

  • KTI Networks 10BASE-T - page 7

    Features • Complies with IEEE 802.3 and IEEE 802.3u standard for Ethernet/Class II Fast Ethernet repeater • Provides a configuration switch (10M/100M/AUTO) to set all 8 TP ports as 10BASE-T ports, 100BASE-TX ports or 10/100 auto-sensing ports. • In AUTO mode, each TP port can support either an Ethernet 10Mbps connection or a Fast Ethernet 100 ...

  • KTI Networks 10BASE-T - page 8

    Dual-speed Hub T echnology Dual-speed hub is designed to support connections with different speeds in the same hub. It makes a network planning simpler, espe- cially when an environment is containing 10Mbps Ethernet and 100Mbps Fast Ethernet technologies. It also allows a smooth mi- gration from an Ethernet network to a Fast Ethernet network. A dua ...

  • KTI Networks 10BASE-T - page 9

    2. Installation Unpacking Check to see that you have everything before you start the installation. • Installation guide • The hub unit • One AC power adapter for the hub • One wall mount kit Checking AC Power Before you begin the installation, check the AC voltage of your area. The AC power adapter which is used to supply the DC power for t ...

  • KTI Networks 10BASE-T - page 10

    The power socket for the AC power adapter is located on the rear of the hub as shown below: Mounting the Hub The hub can be placed on a desktop as a stand-alone unit. It also can be mounted on a wall. The following procedure describes how to mount the hub onto a wallboard or wood (a stud, heavy wooden paneling, etc.) using the wall mount kit suppli ...

  • KTI Networks 10BASE-T - page 11

    3. Place the hub against the wall so that the mount bracket fits into the slot bracket on the back of the hub. 4. Slide the hub down until it hangs on the mount bracket. 6 ...

  • KTI Networks 10BASE-T - page 12

    3. Making Network Connections Network Connectors and Rear Switch The hub provides 8 dual-speed TP ports. Each can support one con- nection to either a 10BASE-T Ethernet device or a 100BASE-TX Fast Ethernet device using 2-pair UTP cable. One configuration switch is located on the rear panel. The switch is used for setting the operation mode for the ...

  • KTI Networks 10BASE-T - page 13

    RJ-45 Connectors Each of Port #1 to Port #7 provides one RJ-45 connector, which are implemented as MDI-X jack. An MDI-X jack is designed with internal crossover function. The function allows a connection to a computer using straight-through UTP cable. The Port #8 provides one MDI-X RJ-45 connector and one MDI-I RJ-45 connector . Only one connector ...

  • KTI Networks 10BASE-T - page 14

    Connecting to Computers The RJ-45 connectors labeled 1X to 8X can be used for connecting to the network adapter installed in a computer . The network adapter can be a 10BASE-T adapter, a 100BASE-TX adapter, or a 10/100 dual-speed NW ay adapter . The following table lists the cables used for connecting to different network adapters: Adapter connecte ...

  • KTI Networks 10BASE-T - page 15

    Connecting to Hubs The following table lists the types and the maximum number of hub connections depending on the configuration switch setting: Configuration T ypes of hubs Connections 10M mode 10BASE-T hubs up to 8 100M mode 100BASE-TX Class II hub one 100M mode Dual-speed Class II hub one AUTO mode 10BASE-T hubs up to 8 AUTO mode 100BASE-TX Class ...

  • KTI Networks 10BASE-T - page 16

    Connecting to a Fast Ethernet Hub Since the KF-8D is designed to comply with IEEE 802.3u Class II repeater specifications, it can support one connection to another 100BASE-TX Class II hub. The connection rules are: 1. The other hub which is connected to KF-8D must comply with IEEE 802.3u Class II repeater specifications. 2. No more than two hubs ca ...

  • KTI Networks 10BASE-T - page 17

    4. Interpreting LED Indicators The following figure shows the locations of the LED indicators: Power LED : indicates the status of the repeater power source. State Indication Interpretation On Normal The power of the hub is on. O f f Problem No power is being supplied to the hub. Collision LED : indicates the collision detected by the hub. The LED ...

Fabbricante KTI Networks Categoria Switch

I documenti che otteniamo dal fabbricante del dispositivoKTI Networks 10BASE-T possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici KTI Networks
- manuali per l’uso 10BASE-T
- schede prodotto KTI Networks
- opuscoli
- o etichette energetiche KTI Networks 10BASE-T
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso KTI Networks 10BASE-T.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione KTI Networks 10BASE-T, manuali di manutenzione, brevi manuali o manuali utente KTI Networks 10BASE-T. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto KTI Networks 10BASE-T.

Manuali per l’uso simili

Manuale completo del dispositivo KTI Networks 10BASE-T, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare KTI Networks 10BASE-T dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti KTI Networks 10BASE-T.

Il manuale per l’uso completo KTI Networks, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale KTI Networks 10BASE-T - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice KTI Networks 10BASE-T, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per KTI Networks 10BASE-T che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo KTI Networks 10BASE-T - che ci dovrebbe aiutare nei primi passi durante l'uso KTI Networks 10BASE-T
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del KTI Networks 10BASE-T
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio KTI Networks 10BASE-T in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su KTI Networks 10BASE-T?

Utilizza il modulo sottostante

Se non hai risolto il problema con KTI Networks 10BASE-T con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con KTI Networks 10BASE-T è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)