KTI Networks 10BASE-Tの取扱説明書

17ページ 0.07 mb
ダウンロード

ページに移動 of 17

Summary
  • KTI Networks 10BASE-T - page 1

    Installation Guide 10BASE-T/100BASE-TX 8-Port Dual-Speed Hub Model: KF-8D DOC.980329-KF8D-K P/N: 750-0109-001 ...

  • KTI Networks 10BASE-T - page 2

    Ó 1998 KTI Networks Inc. All rights reserved. No part of this docu- mentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time t ...

  • KTI Networks 10BASE-T - page 3

    8-Port Dual-Speed Ethernet/Fast Ethernet Hub Installation Guide DOC.980330-KF8D-NK P/N: 750-0109-002 ...

  • KTI Networks 10BASE-T - page 4

    The information contained in this document is subject to change without prior no- tice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are d ...

  • KTI Networks 10BASE-T - page 5

    T able of Contents Chapter 1 Introduction Introduction ............................................................................... 1 Features ................................................................................... 2 Dual-speed Hub T echnology .................................................... 3 Chapter 2 Installation Unpacking ... ...

  • KTI Networks 10BASE-T - page 6

    1. Introduction KF-8D dual-speed Fast Ethernet/Ethernet hub is designed to allow easy and flexible migration from 10Mbps Ethernet to 100Mbps Fast Ethernet. The hub complies with IEEE 802.3 and IEEE 802.3u repeater specifications and supports 10Mbps and 100Mbps con- nectivity over UTP cabling in the same hub. The hub provides 8 dual-speed TP ports. ...

  • KTI Networks 10BASE-T - page 7

    Features • Complies with IEEE 802.3 and IEEE 802.3u standard for Ethernet/Class II Fast Ethernet repeater • Provides a configuration switch (10M/100M/AUTO) to set all 8 TP ports as 10BASE-T ports, 100BASE-TX ports or 10/100 auto-sensing ports. • In AUTO mode, each TP port can support either an Ethernet 10Mbps connection or a Fast Ethernet 100 ...

  • KTI Networks 10BASE-T - page 8

    Dual-speed Hub T echnology Dual-speed hub is designed to support connections with different speeds in the same hub. It makes a network planning simpler, espe- cially when an environment is containing 10Mbps Ethernet and 100Mbps Fast Ethernet technologies. It also allows a smooth mi- gration from an Ethernet network to a Fast Ethernet network. A dua ...

  • KTI Networks 10BASE-T - page 9

    2. Installation Unpacking Check to see that you have everything before you start the installation. • Installation guide • The hub unit • One AC power adapter for the hub • One wall mount kit Checking AC Power Before you begin the installation, check the AC voltage of your area. The AC power adapter which is used to supply the DC power for t ...

  • KTI Networks 10BASE-T - page 10

    The power socket for the AC power adapter is located on the rear of the hub as shown below: Mounting the Hub The hub can be placed on a desktop as a stand-alone unit. It also can be mounted on a wall. The following procedure describes how to mount the hub onto a wallboard or wood (a stud, heavy wooden paneling, etc.) using the wall mount kit suppli ...

  • KTI Networks 10BASE-T - page 11

    3. Place the hub against the wall so that the mount bracket fits into the slot bracket on the back of the hub. 4. Slide the hub down until it hangs on the mount bracket. 6 ...

  • KTI Networks 10BASE-T - page 12

    3. Making Network Connections Network Connectors and Rear Switch The hub provides 8 dual-speed TP ports. Each can support one con- nection to either a 10BASE-T Ethernet device or a 100BASE-TX Fast Ethernet device using 2-pair UTP cable. One configuration switch is located on the rear panel. The switch is used for setting the operation mode for the ...

  • KTI Networks 10BASE-T - page 13

    RJ-45 Connectors Each of Port #1 to Port #7 provides one RJ-45 connector, which are implemented as MDI-X jack. An MDI-X jack is designed with internal crossover function. The function allows a connection to a computer using straight-through UTP cable. The Port #8 provides one MDI-X RJ-45 connector and one MDI-I RJ-45 connector . Only one connector ...

  • KTI Networks 10BASE-T - page 14

    Connecting to Computers The RJ-45 connectors labeled 1X to 8X can be used for connecting to the network adapter installed in a computer . The network adapter can be a 10BASE-T adapter, a 100BASE-TX adapter, or a 10/100 dual-speed NW ay adapter . The following table lists the cables used for connecting to different network adapters: Adapter connecte ...

  • KTI Networks 10BASE-T - page 15

    Connecting to Hubs The following table lists the types and the maximum number of hub connections depending on the configuration switch setting: Configuration T ypes of hubs Connections 10M mode 10BASE-T hubs up to 8 100M mode 100BASE-TX Class II hub one 100M mode Dual-speed Class II hub one AUTO mode 10BASE-T hubs up to 8 AUTO mode 100BASE-TX Class ...

  • KTI Networks 10BASE-T - page 16

    Connecting to a Fast Ethernet Hub Since the KF-8D is designed to comply with IEEE 802.3u Class II repeater specifications, it can support one connection to another 100BASE-TX Class II hub. The connection rules are: 1. The other hub which is connected to KF-8D must comply with IEEE 802.3u Class II repeater specifications. 2. No more than two hubs ca ...

  • KTI Networks 10BASE-T - page 17

    4. Interpreting LED Indicators The following figure shows the locations of the LED indicators: Power LED : indicates the status of the repeater power source. State Indication Interpretation On Normal The power of the hub is on. O f f Problem No power is being supplied to the hub. Collision LED : indicates the collision detected by the hub. The LED ...

メーカー KTI Networks カテゴリー Switch

KTI Networks 10BASE-Tのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 10BASE-Tの取扱説明書
- KTI Networksの製品カード
- パンフレット
- またはKTI Networks 10BASE-Tの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、KTI Networks 10BASE-Tの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、KTI Networks 10BASE-Tの取り付け説明書、サービスマニュアル、簡易説明書、またはKTI Networks 10BASE-Tのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、KTI Networks 10BASE-Tの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

KTI Networks 10BASE-Tデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKTI Networks 10BASE-Tを使用するのを助ける技術的文書のことです。説明書は通常、全てのKTI Networks 10BASE-Tユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

KTI Networksの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. KTI Networks 10BASE-Tの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKTI Networks 10BASE-Tの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。KTI Networks 10BASE-Tに関してこのドキュメントで見つけることができる全てのヒントの目次
3. KTI Networks 10BASE-Tデバイスの基本機能を使うにあたってのヒント。 KTI Networks 10BASE-Tのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。KTI Networks 10BASE-Tに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKTI Networks 10BASE-Tのメーカー/サービスへの連絡先に関する情報。

KTI Networks 10BASE-Tについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもKTI Networks 10BASE-Tの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKTI Networks 10BASE-Tで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)