-
Roper llc-200 - page 1
4411-0068 Version 1.A December 10, 1997 ...
-
Roper llc-200 - page 2
...
-
Roper llc-200 - page 3
iii Table of Contents Model IIC-200 Image Intensifier Controller ........................................................ 5 Introduction ......................................................................................................................... 5 Dangers and Warnings .................................................................... ...
-
Roper llc-200 - page 4
iv Model IIC-200 Operation Manual Version 1.A This page intentionally left blank. ...
-
Roper llc-200 - page 5
5 Model IIC-200 Image Intensifier Controller Introduct ion The IIC-200 is a stand-alone image intensifier controller. It supplies high-voltage DC bias for Princeton Instruments image intensifiers plus circuitry to facilitate gating. Gating pulses are provided by a Princeton Instruments high voltage pulser. The IIC-200 allows front-panel control of ...
-
Roper llc-200 - page 6
6 Model IIC-200 Operation Manual Version 1.A The IIC-200 allows both Shutter and Gated modes of operation. Gating pulses can range from 5 nsec to DC. Longer gate experiments can also use the 5 volt logic electronic shutter control. Danger s and Warnings Voltages inside the IIC-200 may exceed 10,000 volts. To avoid possible hazard to personnel, use ...
-
Roper llc-200 - page 7
Version 1.A Model IIC-200 Operation Manual 7 Note: The Model IIC-200 has automatic circuitry to help prevent damage. However, it is far better not to place an expensive intensifier at risk than to depend on the protection circuitry. Features Independently variable MCP power supply, independent of phosphor voltage. Automatic alarm and shutdown in ca ...
-
Roper llc-200 - page 8
8 Model IIC-200 Operation Manual Version 1.A Front Pane l Feature s MCP GA IN: This adjustment is used to control the gain of the MCP by controlling the voltage across it. Display units are arbitrary. SHUTTER/GATE: This switch selects between Gate mode or Shutter mode. In Gate mode, the intensifier is normally off and a high-voltage gate pulse is n ...
-
Roper llc-200 - page 9
Version 1.A Model IIC-200 Operation Manual 9 The plug on the line cord supplied with the system should be compatible with the line-voltage outlets in common use in the region to which the system is shipped. If the line cord plug should prove to be incompatible, a compatible plug should be installed, taking care to maintain the proper polarity to pr ...
-
Roper llc-200 - page 10
10 Model IIC-200 Operation Manual Version 1.A Hardware O verview The IIC-200 consists of a printed circuit board and a modular high voltage supply which are mounted in a stand-alone chassis. The IIC-200 contains circuitry for the following functions: A variable high voltage power supply for the MCP voltage. The MCP voltage is a linear function of t ...
-
Roper llc-200 - page 11
Version 1.A Model IIC-200 Operation Manual 11 Shutter circuitry which allows an electrically isolated logic signal to control the voltage between the Photocathode and MCP In. This allows long gate times or C W operation. Operatio n ➧ Review the Danger and Warning notices on page 6 before operating the IIC-200. ➧ Set the IIC-200 Power switch to ...
-
Roper llc-200 - page 12
12 Model IIC-200 Operation Manual Version 1.A Connections with a Gen IV I ntensi fi er ➧ Connect one end of the high-voltage cable supplied by Roper Scientific to the high-voltage connector on the image intensifier. If you have purchased more than one image intensifier, make sure you are using the cable supplied with this intensifier. The connect ...
-
Roper llc-200 - page 13
Version 1.A Model IIC-200 Operation Manual 13 Power Up Steps ➧ Make sure the front-panel MCP Power switch is O ff. Adjust MCP G ain to minimum and turn on the chassis power. Note: As long as the image intensifier and IIC-200 are purchased from Roper Scientific as part of the same order, the upper limit circuit will be set for the maximum safe lim ...
-
Roper llc-200 - page 14
14 Model IIC-200 Operation Manual Version 1.A Scientific highly recommends updating old units at the user’s earliest convenience. Contact the factory for details. Connecting the wrong cable at both ends can result in non-functioning of the image intensifier. If you suspect that you may be using the wrong cable for your intensifier, contact the fa ...
-
Roper llc-200 - page 15
15 Warranty & Service Warranty This equipment is warranted to be free from defects of material and workmanship. It is sold subject to the mutual agreement that the liability of Roper Scientific is limited to replacing defective parts and/or repairing malfunctioning equipment at its factory, provided the equipment is returned, transportation pre ...
-
Roper llc-200 - page 16
16 Model IIC-200 Operation Manual Version 1.A Con tact Informatio n Roper Scientific’s manufacturing facility is located at the following address: Roper Scientific 3660 Quakerbridge Road Trenton, NJ 08619 (USA) Tel: 609-587-9797 Fax: 609-587-1970 Tech Support E-mail: techsupport@roperscientific.com For technical support and service outside the Un ...
-
Roper llc-200 - page 17
17 Index Alarm circuit, 10 Audio beeper, 7 Auto Bright Co ntrol switch, 8 Auto Bright ness C ontrol, 7, 10 Beeper, 7 Bias levels MCP-In, 7 MCP-Out, 7 phosphor, 7 Brightnes s control, 7, 10 Contact informat ion, 16 e-mail address, 16 street address, 16 teelphone and fax numbers, 16 web site, 16 CW mod e, 7 CW operation (Gen IV), 12 Fuses, 9 Gain red ...
-
Roper llc-200 - page 18
18 Model IIC-200 Operation Manual Version 1.A This page intentionally left blank. ...
Roper llc-200についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもRoper llc-200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRoper llc-200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。