Knoll Systems PRM200の取扱説明書

6ページ 0.15 mb
ダウンロード

ページに移動 of 6

Summary
  • Knoll Systems PRM200 - page 1

    PRM150, PRM200 Advanced Power Conditioners Installation Instructions v1.1 Warning : To be installed and/or used in accordance with appropriate electrical codes and regulations Introduction: Thank you for your purchase of a Knöll PRM150 or PRM200 Advanced Power Conditioner and congratulations on your choice. This specially made conditioner is desig ...

  • Knoll Systems PRM200 - page 2

    Coaxial surge suppression is often over looked. A convenient “F” connector is provided both for cable TV and the satellite dish. This allows full surge protection through a low loss pass through connection. Telephone line surge protection is provided to bring an added measure of safety to your home. An RJ connector is provided for both in and o ...

  • Knoll Systems PRM200 - page 3

    Installation: The PRM200 power source connection must be adequate for use at 20 amps. We recommend a properly grounded 30-amp circuit, wired with 10-gauge wiring, if continuous operation near 20 amps is anticipated. A dedicated (nothing else connected) 20-amp circuit is the minimum acceptable to comply with NEC requirements. Consult a qualifi ed el ...

  • Knoll Systems PRM200 - page 4

    Delayed Turn On’s . When the power conditioner is turned on, th e two outlets labelled “Delay Min” turn on immediately (along with the unswitch ed outlets already turned on). About two seconds later the next tw o outlets labelled “Delay Med” turn on. About two seconds later (four seconds from wh en the power conditioner was first turned o ...

  • Knoll Systems PRM200 - page 5

    Fuses There is a single slow blow 15-amp fuse in the PRM150 and there is a single 20 amp slow blow fuse in the PRM200. As per safety regulations, only authorized and experienced service people, including Knoll factory personnel are authorized to change these fuses. DO NOT CHANGE these fuses for safety reasons. Cable TV and Satellite Dish For best p ...

  • Knoll Systems PRM200 - page 6

    PRM150 and PRM200 SPECIFICATIONS Current rating: PRM150 15 amps (1800 watts at 60/120 VAC, 60 HZ) fuse protected. PRM200 20 amps (2400 watts at 60/120 VAC, 60 HZ) fuse protected. Voltage Ranges: 90-135 VAC 60 Hz Remote trigger voltage: 3-24 VDC (input impedance 1k ohm) Clamping Voltage 250v peak (175 volts RMS) Response time: 1 nanosecond Max Surge ...

メーカー Knoll Systems カテゴリー Power Supply

Knoll Systems PRM200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PRM200の取扱説明書
- Knoll Systemsの製品カード
- パンフレット
- またはKnoll Systems PRM200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Knoll Systems PRM200の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Knoll Systems PRM200の取り付け説明書、サービスマニュアル、簡易説明書、またはKnoll Systems PRM200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Knoll Systems PRM200の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Knoll Systems PRM200デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKnoll Systems PRM200を使用するのを助ける技術的文書のことです。説明書は通常、全てのKnoll Systems PRM200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Knoll Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Knoll Systems PRM200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKnoll Systems PRM200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Knoll Systems PRM200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Knoll Systems PRM200デバイスの基本機能を使うにあたってのヒント。 Knoll Systems PRM200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Knoll Systems PRM200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKnoll Systems PRM200のメーカー/サービスへの連絡先に関する情報。

Knoll Systems PRM200についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもKnoll Systems PRM200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKnoll Systems PRM200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)