-
Delta 50-840 - page 1
INSTRUCTION MANUAL One H.P . Single-S t age Dust Collector (Model 50-840) D A T E D 10-12-97 P A R T NO. 1347662 'Delt a International Machinery Corp. 1997 ...
-
Delta 50-840 - page 2
2 T ABLE O F CONTENTS SAFETY RULES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 IMPORT A N T SAFETY RULES F O R DUST C OLLECT O R S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 U N P ACKING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Delta 50-840 - page 3
3 IMPORT ANT SAFETY RULES W oodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery , there are cert a in hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the pos si - bility of personal injury . However , i f normal safety pre ...
-
Delta 50-840 - page 4
4 IMPORT A N T SAFETY RULES F O R DUST COLLECT O R S W ARNING: Basic precautions should always be followed when using your dust collector . T o reduce the risk of injury , electrical shock or fire, comply with the safety rules listed below: 1 . READ and underst and the instruction manual before operating the dust collector . 2 . D O N O T leave the ...
-
Delta 50-840 - page 5
5 1 - Motor and Blower assembly 2 - Base 3 - Casters (4) 4 - 10-24 x 3/8 p a n head screws (16) 5 - 5/16-18 hex nut, lockwasher and flat washer for mounting filter bag support rod 6 - Open-end wrench 7 - 1/4-20 x 1/2 hex head screws for mounting support tube to motor and blower assembly (3) U N P ACKING Fig. 2 8 - 5/16-18 x 1/2 hex head screws for ...
-
Delta 50-840 - page 6
6 Fig. 3 Fig. 4 ASSEMBLING CASTERS T O BASE T urn base (A) Fig. 3, over . Align four holes (B) in caster with holes at the corner of the base and assemble caster (C) to base with four p an head screws (D). Assemble the remaining three casters (C ) Fig. 4, to the base in the same manner . ASSEMBL Y A D C B C C ...
-
Delta 50-840 - page 7
7 ASSEMBLING SUPPORT TUBE A N D M O T O R AN D BLOWER ASSEMBL Y T O BASE 1 . Place the motor and blower assembly (A) Fig. 5, u p side down on a sturdy supporting surface. 2 . Find the support tube (B) Fig. 5, and three 1/2 inch- long hex head screws (C). 3 . Carefully place support tube (B) Fig. 6, over the moto r impellers (D). Align three holes ( ...
-
Delta 50-840 - page 8
8 Fig. 10 Fig. 1 1 Fig. 12 Fig. 13 ASSEMBLING F I L T E R A N D DUST COLLECTION BAGS T O DRUM 1 . Thread 5/16 hex locknut (A) Fig. 10, onto the end of bag support rod (B). Place lockwasher and flat wash - e r ( C) Fig. 10, onto bag support rod (B). Thread rod into hole (D) and tighten locknut (A) against motor and blower assembly (E) to hold suppor ...
-
Delta 50-840 - page 9
9 ASSEMBLING DUST I N T A K E HOSE T O M O T O R A N D BLOWER ASSEMBL Y The dust collector is supplied with a 4 flexible dust i n t ake hose. T o assemble the dust collection hose to the motor and blower assembly , loosely att ach hose clamp (A) Fig. 14, around one end of flexible hose (B) and assemble the hose to dust int ake port (C). T ighten ho ...
-
Delta 50-840 - page 10
10 Fig. 16 Fig. 17 GROUNDED OUTLET B O X CURRENT CARR YING PRONGS GROUNDING BLADE I S LONGEST O F THE 3 BLADES GROUNDED OUTLET B O X GROUNDING MEANS ADAPTER Fig. 18 120 VOL T , SINGLE PHASE OPERA TION This tool must be grounded while in use to protect the operator from electric shock. The motor recommended for use with your dust collector is shippe ...
-
Delta 50-840 - page 11
11 OPERA TING CONTROLS FO R OPERA T O R SAFETY , BEFORE OPERA TING T H E MACHINE, MAKE CERT A I N T H A T THE DUST I N T A K E HOSE I S AL W A YS A T T ACHED T O TH E DUST I N T A K E PORT . TH E R OT A TING F A N LOCA TE D INSIDE T H E B L O W E R HOUSING I S ACCESSIBLE THROUGH T HE DUST IN- T A KE PORT A N D C A N B E HAZARDOUS. A L W AY S WEAR P ...
-
Delta 50-840 - page 12
Printed in U.S.A. 12 Delt a will rep air or replace, at it s expense and at it s option, any Delt a machine, machine p art, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prep aid to a Delt a factory service center or authorized service st ation with pro ...
Delta 50-840についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもDelta 50-840の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta 50-840で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。