Snapper ELT19540RDの取扱説明書

42ページ 1.26 mb
ダウンロード

ページに移動 of 42

Summary
  • Snapper ELT19540RD - page 1

    OPERA T OR’S MANU AL 19.5 HP Hydr o T ractors Mfg. No. Title Description 2690782 19.5 HP Simplicity Regent XL RD , 19.5 HP OHV 2690784 19.5 HP Snapper EL T19540RD 22 HP Hydr o T ractors Mfg. No. Title Description 2690783 22 HP Simplicity Regent XL RD , 22 HP V -T win 2690785 22 HP Snapper EL T2240RD Regent XL / RD Series 1736042 Revision 00 Rev. ...

  • Snapper ELT19540RD - page 2

    ...

  • Snapper ELT19540RD - page 3

    1 Air Filter & Pre-Cleaner Service (V-Twin Models) ....................................................27 Air Filter & Pre-Cleaner Service (Single Cylinder Models) .......................................28 Replace Spark Plugs ............................................29 T roubleshooting, Adjustment & Service .........31 Troubleshootin ...

  • Snapper ELT19540RD - page 4

    2 Safety Rules & Information Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Power equipment is only as safe as the operator. If it is misused, or not properly maintained, it can be dangerous! Rem ...

  • Snapper ELT19540RD - page 5

    3 Safety Rules and Information Slope Operation You could be seriously injured or even killed if you use this unit on too steep an incline. Using the unit on a slope that is too steep or where you don’t have adequate traction can cause you to lose control or roll over. A good rule of thumb is to not operate on any slope you cannot back up (in 2-wh ...

  • Snapper ELT19540RD - page 6

    4 Safety Rules & Information GENERAL OPERA TION 1. Read, understand, and follow all instructions in the manual and on the unit before starting. 2. Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. 3. Only allow responsible adults, who are familiar with the instructions, to opera ...

  • Snapper ELT19540RD - page 7

    5 Safety Rules and Information CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit and the mowing activity. Never assume that children will remain where you last saw them. 1. Keep children out of the mowing area and under the watchful care of another responsible adul ...

  • Snapper ELT19540RD - page 8

    6 Safety Rules & Information SER VICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. 2. Use only approved gasoline containers. 3. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool before refueling. 4. Never fuel the machine indoors. 5. Ne ...

  • Snapper ELT19540RD - page 9

    7 Identification Numbers Tractor ID Tag Mower ID Tag When contacting your authorized dealer for replacement parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identification numbers, and engine serial numbers in the space provided for easy access. These numbers can be found in the locations s ...

  • Snapper ELT19540RD - page 10

    8 Safety Decals Warning: Read Operator’s Manual. Read and understand the Operator’s Manual before using this machine. Danger: Thrown Objects. This machine is capable of throwing objects and debris. Keep bystanders away. Warning: Remove Key Before Servicing. Remove the key and consult technical literature before performing repairs or maintenance ...

  • Snapper ELT19540RD - page 11

    9 CE Safety Icons Transmission Release Part No. 1735265 173xxxx Operating Instructions, CE Models, Part No. 1734027 Attachment Lift Part No. 1730264 Fuel Level Part No. S532-0-8732-762-3 R 4 3 2 R 4 3 2 Ignition Switch Positions Part No. 1722806 Decal Locations ...

  • Snapper ELT19540RD - page 12

    10 Features & Controls Throttle Contr ol The throttle controls engine speed. Move the throttle forward to increase engine speed and back to decrease engine speed. Always operate at FULL throttle. Choke Close the choke for cold starting. Open the choke once the engine starts. A warm engine may not require choking. Move the lever forward to close ...

  • Snapper ELT19540RD - page 13

    Rever se Mowing Option (RMO) The Reverse Mowing Option allows for mowing (or use of other PTO driven attachments) while traveling in reverse. If you choose to mow in reverse, turn the RMO key after the PTO is engaged. The L.E.D. light will illuminate, and the operator can then mow in reverse. Each time the PTO is engaged the RMO needs to be reactiv ...

  • Snapper ELT19540RD - page 14

    12 Features & Controls Figure 1. Engaging the Parking Brake A. Ground Speed Pedals B. Brake Pedal C. Parking Brake Knob D. Cruise Control Knob E. Hour Meter P arking Brake Function Applying the Parking Brake - See Figure 2. To lock the parking brake, release the ground speed pedals (A), fully depress the brake pedal (B), pull UP on the parking ...

  • Snapper ELT19540RD - page 15

    13 Operating the T ractor General Operating Safety Be sure to read all information in the Safety and Operation sections before attempting to operate this unit. Become familiar with all of the controls and how to stop the unit. Adding Fuel To add fuel: 1. Remove the fuel cap (A, Figure 3). 2. Fill the tank. Do not overfill. Leave room in the tank fo ...

  • Snapper ELT19540RD - page 16

    14 Operating the T ractor Stopping the T ractor & Engine 1. Return the ground speed control(s) to neutral. 2. Disengage the PTO and wait for all moving parts to stop. 3. Briggs & Stratton Models: Move the throttle control to SLOW position and turn the ignition key to OFF. Remove the key. Driving the T ractor 1. Sit in the seat and adjust th ...

  • Snapper ELT19540RD - page 17

    Figure 5. Removing & Installing Belt A. Idler Arm B. PTO Pulley 15 Operating the T ractor Figure 4. Mower Deck Removal and Installation (viewed from underneath right side of tractor) A. Hair Pins D. Upper Spring B. Trunions E. Lower Spring (2) C. Lift Arm F. Lift Rod A B Figure 3. Mower Lift Lever (Lowered Position) A. Lift Lever A Figure 6. Mo ...

  • Snapper ELT19540RD - page 18

    16 Operating the T ractor Installing the Mower Dec k 1. Park tractor, shut off PTO and engine, remove the key and apply parking brake. Turn the wheels fully to the left and slide mower deck under right side of tractor. 2. From the rear with the grass catcher open pull discharge chute to rear. 3. Push the discharge chute tube (A, Figure 7) toward th ...

  • Snapper ELT19540RD - page 19

    17 Operating the T ractor Figure 9. Raising & Lowering Mower A. Mower Lift Lever Cutting Height Adjustment The mower lift lever (A, Figure 9) is used to lower the deck to cutting position and raise the deck to transport position. To lower the deck, pull back slightly on the mower lift lever (A), push it to the left and slide it down. To raise t ...

  • Snapper ELT19540RD - page 20

    18 Regular Maintenance Maintenance Schedule & Pr ocedures The following schedule should be followed for normal care of your tractor and mower. • = All Models B & S = Briggs & Stratton Models * Refer to engine owner’s manual. Change original engine oil after initial break-in period. ** More often in hot (over 85° F: 30° C) weather ...

  • Snapper ELT19540RD - page 21

    19 Regular Maintenance Safety Interloc k System Check Service Interval: Every Fall & Spring Check the function of the safety interlock system using the test procedure found on page 13 of this manual. If the tractor fails any of the tests, see your dealer. Blade Brake Chec k Service Interval: Every 100 Hours or Fall & Spring Mower blades and ...

  • Snapper ELT19540RD - page 22

    20 Regular Maintenance Figure 13. Transmission ID Tag Location A. ID Tag TUFF TORQ K46Z 10010101010 10010101 T ransmission Identification To determine what transmission is in your tractor, check the identification tag attached to the axle of the transmission (Figure 13), or check your tractor’s parts book. T ransmission Maintenance The K46 transm ...

  • Snapper ELT19540RD - page 23

    21 Regular Maintenance Figure 16. Tractor Lubrication Points Lubrication Service Interval: Every 25 Hours Lubricate the unit at the locations shown in Figures 16- 20 as well as the lubrication points listed. Generally, all moving metal parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys. Wipe surf ...

  • Snapper ELT19540RD - page 24

    Regular Maintenance 22 Lubricate Rear Axle Shafts Service Interval: Yearly We recommend removing the rear wheel hubs and lubricating the axle shafts yearly. This prevents the wheel hubs from seizing onto the axle shaft and makes future service easier. 1. Turn off the ignition, turn off the PTO, engage the parking brake, and block the front tires. 2 ...

  • Snapper ELT19540RD - page 25

    W ARNING For your personal safety, do not handle the sharp mower blades with bare hands. Careless or improper handling of blades may result in serious injury. W ARNING For your personal safety, blade mounting capscrews must each be installed with a hex washer and spring washer, then securely tightened. Tighten blade mounting capscrew to 30 +/- 3 Nm ...

  • Snapper ELT19540RD - page 26

    A A Figure 24. Blade Installation A. Capscrew B. Spring Washer C. Alignment Pin D. Blade E. Spline Washer F. Blade Adapter 24 Regular Maintenance Figure 25. Check Blade Timing Chec k Mower Blade Timing Service Interval: Yearly 1. Turn the PTO OFF, engage the parking brake, turn the engine off, and remove the key. Remove the mower deck (see “Mower ...

  • Snapper ELT19540RD - page 27

    25 Regular Maintenance Chec k & Fill Engine Oil Service Interval: Before each use, and every 8 hours. 1. Turn the engine off, and set the parking brake to PARK. 2. Clean the area around the dipstick (C, Figure 26 or 27). 3. Remove the dipstick (C) and clean it with a paper towel. 4. Insert the dipstick (C) back into the engine. Briggs & Str ...

  • Snapper ELT19540RD - page 28

    26 Regular Maintenance Figure 29. Oil Drain Valve A. Engine Block / Valve Base B. Oil Drain Valve C. Cover D. Nipple A A B B C C D Oil Drain V alve Operation 1. Place a suitable container with a 4 quart capacity under the oil drain valve (A, Figure 26 or 27). 2. Loosen or remove the dipstick (C). 3. Wipe oil drain valve (B, Figure 29) and cover (C) ...

  • Snapper ELT19540RD - page 29

    27 Regular Maintenance Figure 30. Air Filter Assembly - V-Twin Models A. Knobs B. Cover C. Air Filter D. Pre-Cleaner Air Filter & Pre-Cleaner Service V-TWIN MODELS Service Interval: Pre-Cleaner: Every 25 hours or as required. Air Filter: Every 50 hours or as required. Replacement Interval: Pre-Cleaner: As required. Air Filter: Every 200 hours o ...

  • Snapper ELT19540RD - page 30

    28 Regular Maintenance 1. 2. 3. Figure 32. Air Filter Assembly - Single Cylinder Models A. Latch B. Cover A B Air Filter & Pre-Cleaner Service SINGLE CYLINDER MODELS - BRIGGS & STRATTON Service Interval: Pre-Cleaner: Every 25 hours or as required. Air Filter: Every 50 hours or as required. Replacement Interval: Pre-Cleaner: As required. Air ...

  • Snapper ELT19540RD - page 31

    29 Figure 34. Spark Plug Gapping Replace Spark Plug Service Interval: Yearly Spark Plug Gap: .030” (.76mm) Replacement Spark Plug Resistor Spark Plug, Champion RC12YC 1. Stop the engine and allow it to cool. 2. Clean the area around the spark plug (see Figure 34 or 35). 3. Remove the spark plug. 4. Check the spark plug gap. It should be .030”. ...

  • Snapper ELT19540RD - page 32

    30 Regular Maintenance ...

  • Snapper ELT19540RD - page 33

    31 T roubleshooting, Adjustment, & Service T r oubleshooting While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most common problems, their causes, and re ...

  • Snapper ELT19540RD - page 34

    32 T roubleshooting, Adjustment, & Service T ractor T roubleshooting Cont. Tractor drive belt slips. 1. Pulleys or belt greasy or oily. Clean as required. 2. Belt stretched or worn. See Dealer. 3. Idler pulley pivot bracket Remove idler pulley bracket, clean and lubricate. “frozen” in declutched position. Brake will not hold. 1. Internal br ...

  • Snapper ELT19540RD - page 35

    33 T roubleshooting, Adjustment, & Service Figure 36. Seat Adjustment A. Seat Adjustment Lever Figure 37. Fuse A. Fuse, 20-amp B. Fuse Holder B A Figure 38. Blade Type Fuse A. Good Fuse with Solid Fusible link B. No Good Fuse with Broken Fusible link Solid Fusible Link Broken Fusible Link B A Seat Adjustment The seat can be adjusted forward and ...

  • Snapper ELT19540RD - page 36

    34 T roubleshooting, Adjustment, & Service PT O Clutch Adjustment Check the PTO clutch adjustment after every 250 hours of operation. Also perform the following procedure if the clutch is slipping or will not engage, or if a new clutch has been installed. 1. Remove key from ignition switch and disconnect spark plug wires to prevent the possibil ...

  • Snapper ELT19540RD - page 37

    35 T roubleshooting, Adjustment, & Service Mower Belt Replacement 1. Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, shut the engine off, and remove the key. 2. Remove the mower deck (see “Mower Deck Removal”). 3. Remove the belt cover for the PTO pulley (A, Figure 41). 4. R ...

  • Snapper ELT19540RD - page 38

    36 T roubleshooting, Adjustment, & Service Figure 44. Tighten Idler Assembly Capscrew A. 3/8” Ratchet and Extension Figure 42. Mower Blade Timing A Arbor Drive Belt Replacement 1. With the deck installed, park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, engage the parking brake, shut the engine off, and ...

  • Snapper ELT19540RD - page 39

    37 ENGINE: 22 HP* Briggs & Stratton Make Briggs & Stratton Model Intek Horsepower 22 @ 2700 +/- 100 rpm Displacement 44.2 Cu. in (724 cc) Electrical System 12 Volt, 9 amp. Alternator, Battery: 230 CCA Oil Capacity 64 Oz. (1.9 L) 19.5 HP* Briggs & Stratton Make Briggs & Stratton Model Intek Horsepower 19.5 @ 2700 +/- 100 rpm Displace ...

  • Snapper ELT19540RD - page 40

    38 Parts & Accessories Replacement P ar ts Replacement parts are available from your authorized dealer. Engine Oil Touch-Up Paint Grease Gun Kit 8 oz. Grease Tube Tire Sealant Degrimer/Degreaser Gas Stabilizer Maintenance Items Many convenient and helpful service and maintenance items are available from you authorized dealer. Some of these item ...

  • Snapper ELT19540RD - page 41

    ...

  • Snapper ELT19540RD - page 42

    500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.SimplicityMfg.com Briggs & Stratton Yard Power Products Group Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved ...

メーカー Snapper カテゴリー Lawn Mower

Snapper ELT19540RDのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ELT19540RDの取扱説明書
- Snapperの製品カード
- パンフレット
- またはSnapper ELT19540RDの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Snapper ELT19540RDの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Snapper ELT19540RDの取り付け説明書、サービスマニュアル、簡易説明書、またはSnapper ELT19540RDのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Snapper ELT19540RDの製品を使用するにあたって最も人気のある説明書を閲覧できます。

Snapper ELT19540RDデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSnapper ELT19540RDを使用するのを助ける技術的文書のことです。説明書は通常、全てのSnapper ELT19540RDユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Snapperの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Snapper ELT19540RDの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSnapper ELT19540RDの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Snapper ELT19540RDに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Snapper ELT19540RDデバイスの基本機能を使うにあたってのヒント。 Snapper ELT19540RDのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Snapper ELT19540RDに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSnapper ELT19540RDのメーカー/サービスへの連絡先に関する情報。

Snapper ELT19540RDについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSnapper ELT19540RDの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSnapper ELT19540RDで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)