日本語 dropdown-ico

Cisco Systems 6200の取扱説明書

32ページ 0.35 mb
ダウンロード

ページに移動 of 32

Summary
  • Cisco Systems 6200 - page 1

    CHAPTER Cisco 6200 User Guide 1-1 1 Hardw are Descr iption This chapter provides an o vervie w of the Cisco 6200 advanced digital subscriber line access multiplex er (DSLAM) and describes the system’ s hardware components. The chapter is arranged as follows: • Cisco DSL Product Family on page 1-1 • Cisco 6200 Chassis on page 1-2 • Network T ...

  • Cisco Systems 6200 - page 2

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-2 The Cisco DSL family also includes a Frame Relay IDSL multiplex er , a service selection gatew ay , the Cisco 605 card, the Cisco 6100 DSLAM, and an A TM switch to aggregate Cisco 6200 traf fic. 1.2 Cisco 6200 Chassis This section describes the chassis that houses the Cisco 6200 ...

  • Cisco Systems 6200 - page 3

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-3 Figure 1-1 Cisco 6200 Chassis, Front Vie w 1.2.2 Bac kplane Located behind the module compartment, the backplane provides the follo wing services: • Interconnects the MPC, NTC, and SLCs • Connects the SLCs with the subscribers (local loops) or the PO TS splitter • Distribute ...

  • Cisco Systems 6200 - page 4

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-4 Figure 1-2 Cisco 6200 Chassis, Rear View Primar y (A) and Secondar y (B) H-Buses The backplane’ s primary and secondary H-buses (horizontal buses) link the MPC, NTC, and SLCs. In this release, the primary bus carries all traf fic. The buses operate at 160 Mbps total throughput. ...

  • Cisco Systems 6200 - page 5

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-5 Connections to PO TS Splitters or T elephone Lines On the inner surface of the backplane, the upper and lo wer SLC connectors connect the SLC in the corresponding slot (5 to 14) with unshielded twisted pair (UTP) lines. These lines connect to an external PO TS splitter, and from t ...

  • Cisco Systems 6200 - page 6

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-6 A uxiliar y P or t J40, a 9-pin female connector on the Cisco 6200 backplane, is an EIA/TIA-232 (RS-232) serial port connecting to the management processor card (MPC). J40 is an auxiliary craft port that can be used to connect de vices such as terminals, modems, or laptop computer ...

  • Cisco Systems 6200 - page 7

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-7 The following fixtures are present on the front panel of each PEM: • A green LED that comes on to indicate that –48 VDC power is a v ailable to the chassis • A circuit breaker Note T o turn of f a Cisco 6200 that has two PEMs, you must flip the circuit breakers on both PEM ...

  • Cisco Systems 6200 - page 8

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-8 T able 1-1 Cisco 6200 DSLAM Specifications T able 1-2 Standards and Certifications Specification Description Components 14-slot card compartment Backplane Fan compartment Power module compartment Power input Dual inputs, each –48 VDC T ested voltages: –48V and –57V T oler ...

  • Cisco Systems 6200 - page 9

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-9 1.3 Netw ork T runk Car ds (NTCs) This section describes the OC-3c and STM-1 network trunk cards (NTCs). The NTC module resides in slot 1 of the Cisco 6200 chassis. 1.3.1 What is the NTC OC-3? The NTC is a service interface module that concentrates the data traf fic from all Cisc ...

  • Cisco Systems 6200 - page 10

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-10 Figure 1-5 NTC OC-3 Application The optical interface performs the optical-to-electrical and electrical-to-optical con versions. Its other tasks include clock recov ery , o verhead processing, cell delineation, and diagnostic information retriev al. The upstream data transfer uni ...

  • Cisco Systems 6200 - page 11

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-11 The fiber optic communication channels in the single-mode OC-3c card (NTC OC3-SM) operate with laser energy , which can be harmful, especially to the eyes. During normal operation this ener gy is confined to the cable and presents no danger . T o avoid injury when you are conne ...

  • Cisco Systems 6200 - page 12

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-12 T able 1-3 LEDs on the NTC OC-3 LED Color Condition Indicated PO WER Green The module is receiving po wer . READ Y Green Y ellow Off The NTC is experiencing no problems. The NTC failed its po wer-on self test; it has a hardware problem. Refer to Chapter 7, “T roubleshooting. ? ...

  • Cisco Systems 6200 - page 13

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-13 1.3.3 NTC OC-3 Specifications T able 1-4 lists the physical and electrical specifications of the NTC. T able 1-4 NTC OC-3 Specifications 1.3.4 What is the NTC STM-1? The NTC STM-1 is a service interface module that concentrates the data traf fic from all Cisco 6200 subscriber ...

  • Cisco Systems 6200 - page 14

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-14 The NTC STM-1 also transmits upstream data back to the service provider via A TM on the STM-1 physical layer . The Cisco 6200 uses a fixed mapping of permanent virtual channels (PVCs) between trunk and subscriber ports. This means that no configuration of these circuits is requ ...

  • Cisco Systems 6200 - page 15

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-15 The upstream data transfer unit recei ves data via a 16-bit parallel input from the internal bus on the node’ s backplane. A TM cells are receiv ed from a subscriber line card (SLC) channel only after that channel has won access to the upstream data b us from the other contendi ...

  • Cisco Systems 6200 - page 16

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-16 Figure 1-8 NTC STM-1 Faceplates LED Indicators T able 1-5 describes the LEDs on the faceplate of the NTC STM-1. POWER A C T I V E NTC STM1-SM READY PRIME SEC A TD RD POWER A C T I V E NTC STM1-MM READY PRIME SEC A TD RD 14271 Card status LEDs T ransmit and receive LEDs Reset swit ...

  • Cisco Systems 6200 - page 17

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-17 T able 1-5 LEDs on the NTC STM-1 1.3.6 NTC STM-1 Specifications T able 1-6 lists the physical and electrical specifications of the NTC STM-1. LED Color Condition Indicated PO WER Green The module is receiving po wer . READ Y Green Y ellow Off The NTC is experiencing no problems ...

  • Cisco Systems 6200 - page 18

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-18 T able 1-6 NTC STM-1 Specifications 1.4 Management Pr ocessor Card (MPC) The Cisco 6200 is controlled and managed by the MPC. 1.4.1 Functional Description The MPC performs management and storage tasks for the Cisco 6200 DSLAM. The MPC provides • The Cisco IOS command line inte ...

  • Cisco Systems 6200 - page 19

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-19 The MPC runs a version of Cisco IOS software that is designed for DSL multiple xing. At startup, the MPC loads program software and configuration data from NVRAM, from a server on the network, or from a Flash card in one of its PCMCIA slots. The MPC then pro vides boot images to ...

  • Cisco Systems 6200 - page 20

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-20 Console P or t The console port on the MPC is a serial EIA/TIA-232 port with an RJ-45 connector . See Appendix A, “Pin Assignments, ” for pinouts. PCMCIA Slots and Ejection Buttons The MPC provides two slots for PCMCIA Flash memory cards. PCMCIA cards store system software an ...

  • Cisco Systems 6200 - page 21

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-21 1.4.3 MPC Specifications T able 1-8 lists the physical and electrical specifications of the MPC. T able 1-8 MPC Specifications Specification Description External Interfaces • EIA/TIA-232 console port • 10BaseT Ethernet management port Internal Hardware • MIPS R V4640 pr ...

  • Cisco Systems 6200 - page 22

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-22 1.5 Subscriber Line Car d (SLC) This section describes the CAP and DMT versions of the subscriber line card (SLC). A Cisco 6200 chassis can hold up to 10 SLC modules. Note All the SLCs in a Cisco 6200 chassis should be of the same type. The mixture of CAP and DMT cards in a singl ...

  • Cisco Systems 6200 - page 23

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-23 In the do wnstream direction, 11 rates are av ailable ranging from 640 kbps to 7.168 Mbps. In the upstream direction, 9 rates are av ailable, ranging from 91 kbps to 1.088 Mbps. The modems on the CAP SLC train in sequence, first downstream, then upstream. Each modem first acqui ...

  • Cisco Systems 6200 - page 24

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-24 1.5.2 SLC 8CAP: Ph ysical Description Up to 10 SLCs can be installed in a Cisco 6200 cabinet. The cabinet slots assigned to the SLCs are slot 5 through slot 14. The CAP SLC’ s faceplate is labeled SCL 8CAP . The faceplate (Figure 1-11) includes the fixtures discussed in the fo ...

  • Cisco Systems 6200 - page 25

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-25 T able 1-9 SLC 8CAP LEDs LED Color Condition Indicated PO WER Green The SLC is receiving po wer . READ Y Green Y ellow Off The SLC is experiencing no problems. At least one port on the SLC is in line test mode. The SLC is not communicating with the MPC. This is the case when • ...

  • Cisco Systems 6200 - page 26

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-26 1.5.3 SLC 8CAP Specifications T able 1-10 lists the physical and electrical specifications of the CAP SLC (SLC 8CAP). T able 1-10 SLC 8CAP Specifications Specification Description Subscriber ports 8 per card T ransmission speeds Downstream: up to 7 Mbps Upstream: up to 1 Mbps ...

  • Cisco Systems 6200 - page 27

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-27 1.5.4 What is the SLC 8DMT? The eight-port DMT version of the SLC (SLC 8DMT) is a hot-swappable line module that pro vides data communication between the Cisco 6200 node and up to eight subscribers. Modems on the SLC 8DMT use discrete multitone (DMT) modulation, a common method f ...

  • Cisco Systems 6200 - page 28

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-28 In the upstream direction, the SLC recei ves ADSL signals from a PO TS splitter and demodulates the DMT -modulated signal. Then the SLC channel contends with the other SLC channels for the upstream data bus. T wo priority le vels are av ailable. For the first Cisco 6200 release, ...

  • Cisco Systems 6200 - page 29

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-29 • Number of upstream cells receiv ed with in valid header checksum • Number of errored seconds (this is the number of seconds in which at least one DMT -layer CRC error , loss of signal, or sev erely errored frame is observed), both upstream and do wnstream In addition, the S ...

  • Cisco Systems 6200 - page 30

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-30 Figure 1-13 SLC 8DMT Faceplate Reset Switch The reset switch is recessed behind the faceplate to a void accidental acti vation. It is not for customer use. LED Indicators T able 1-11 describes the LEDs on the faceplate of the SLC. 13067 SLC 8DMT PORTS 1 2 3 4 5 6 7 POWER READY PR ...

  • Cisco Systems 6200 - page 31

    78-5296-02 10/02/98 Hardware Description 1 Cisco 6200 User Guide 1-31 T able 1-11 SLC 8DMT LEDs LED Color Condition Indicated PO WER Green The SLC is receiving po wer . READ Y Green Y ellow Off The SLC is experiencing no problems. At least one port on the SLC is in line test mode. The SLC is not communicating with the MPC. This is the case when • ...

  • Cisco Systems 6200 - page 32

    1 Hardware Description 78-5296-02 10/02/98 Cisco 6200 User Guide 1-32 1.5.6 SLC 8DMT Specifications T able 1-12 lists the physical and electrical specifications of the SLC 8DMT . T able 1-12 SLC 8DMT Specifications Specification Description Subscriber ports 8 per card T ransmission speeds Downstream: up to 8.032 Mbps Upstream: up to 864 kbps Lo ...

メーカー Cisco Systems カテゴリー Server

Cisco Systems 6200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 6200の取扱説明書
- Cisco Systemsの製品カード
- パンフレット
- またはCisco Systems 6200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Cisco Systems 6200の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Cisco Systems 6200の取り付け説明書、サービスマニュアル、簡易説明書、またはCisco Systems 6200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Cisco Systems 6200の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Cisco Systems 6200デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがCisco Systems 6200を使用するのを助ける技術的文書のことです。説明書は通常、全てのCisco Systems 6200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Cisco Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Cisco Systems 6200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははCisco Systems 6200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Cisco Systems 6200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Cisco Systems 6200デバイスの基本機能を使うにあたってのヒント。 Cisco Systems 6200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Cisco Systems 6200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるCisco Systems 6200のメーカー/サービスへの連絡先に関する情報。

Cisco Systems 6200についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもCisco Systems 6200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Systems 6200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)