Quantum QTM300CAの取扱説明書

12ページ 0.42 mb
ダウンロード

ページに移動 of 12

Summary
  • Quantum QTM300CA - page 1

    QTM300CA USER'S GUIDE Cloning Adapter for the QT3xx family of QProx™ ICs The QTM300CA is a cloning adapter designed to interface between any QT3xx 8-pin sensor IC (QT300, QT310, QT320) and a PC or other host device. This adapter permits the designer to upload settings from a PC into the target chip or to read the settings inside a chip. The ...

  • Quantum QTM300CA - page 2

    To begin using the board right away 1. Connect the QTM300CA to a PC using the serial cable (included). Make sure the serial port is not being used by any other application or driver. 2. Connect the QTM300CA to the target board’s 10-pin IDC cloning header; the stripe of the cable connects to the pin marked with a white square . 3. Run QT3View on t ...

  • Quantum QTM300CA - page 3

    Figure 1 - Board Layout If a QT3xx chip has been auto-detected, this button will clone Setups data from the QTM300CA to the chip. The ‘PROG’ LED (see next section) indicates the programming result. The QTM300CA can store three sources of data, one for each part type. The correct source will be used to program the detected part. Program Button T ...

  • Quantum QTM300CA - page 4

    Indicates the programming status of the target chip in Stand-alone mode. The PROG LED will light during the cloning process in Stand-alone mode. Afterwards the LED will flash on/off 3 times to indicate completion: Fast flashing: (0.1s between flashes) the clone process was a success. Slow flashing: (1s between flashes) the clone process failed. If ...

  • Quantum QTM300CA - page 5

    Figure 2 - QT3View Screen Restores a config file saved by (File | Save). All three part selector configurations (tabs) will be restored by this action. Saves all three part selector configurations to disk in a single file, to a file name of your choice. Selects the desired PC serial port. Com1 is selected by default when the software is first start ...

  • Quantum QTM300CA - page 6

    The status bar at the bottom shows the serial port and connection status. Possibilities are: Serial Port Status: - Off Line - COM1: 57600 N 8 1 - COM2: 57600 N 8 1 Connection Status: - Status: Clone connected - Status: Clone & QT300 connected - Status: Clone & QT310 connected - Status: Clone & QT320 connected - Status: No Clone Status B ...

  • Quantum QTM300CA - page 7

    Cloning Directly to a Chip You can read and clone back information to a QT3xx chip directly from your PC without involving the onboard stand-alone memory of the QTM300CA. Here’s how.... Refer to the device data sheet and the QT3View help file for more information on Setup issues. Clone the Setups to the chip:  Upload Setups to the chip from th ...

  • Quantum QTM300CA - page 8

    Clone the Setups to the Chip:  Push the PROG button on the board.  The PROG LED will light to indicate programming status.  The PROG LED will flash to indicate the programming result; see page 4. Step 2 Hook everything up:  Connect the QTM300CA’s cloning cable to the target PCB, or insert a QT3xx chip into the onboard socket.  Powe ...

  • Quantum QTM300CA - page 9

    If the Synchronization input is used, a 10K resistor should be used to avoid problems with the cloning process; see Figure 4 below. QT310 Place the connector as close as possible to the chip. Placing the cloning connector far from the part will increase sensor load capacitance Cx and decrease sensitivity, as some of the cloning lines are also sense ...

  • Quantum QTM300CA - page 10

    Figure 5 - QT320 Clone Connections VSS 8 S2A S1A 2 6 3 C S2B S1B 5 C SCK OUT2 7 OUT2 S2 OUT1 4 OUT1 1 VDD Vdd S1 SDO SDI GND Electrode 2 Electrode 1 l q 10 QTM300CA/R1.02 25.09.03 ...

  • Quantum QTM300CA - page 11

    Table 1 - Clone Cable Functional Pinout - Usage by Part N/C N/C N/C 10 SCK SCK SCK 9 Vcc 1 Vcc 1 Vcc 1 8 SDI SDI SDI / REQ 7 SDO SDO SDO 6 N/C N/C N/C 5 N/C N/C N/C 4 N/C N/C DRDY 3 GND GND GND 2 Vcc 1 Vcc 1 Vcc 1 1 QT320 QT310 QT300 Pin Note 1: Vcc is connected via a 1K pullup on QTM300CA board Table 2- Chip ZIF Socket Order Information www.logica ...

  • Quantum QTM300CA - page 12

    l Q Copyright © 2003 QRG Ltd. All rights reserved. Patented and patents pending Corporate Headquarters 1 Mitchell Point Ensign Way, Hamble SO31 4RF Great Britain Tel: +44 (0)23 8056 5600 Fax: +44 (0)23 8045 3939 admin@qprox.com www.qprox.com North America 651 Holiday Drive Bldg. 5 / 300 Pittsburgh, PA 15220 USA Tel: 412-391-7367 Fax: 412-291-1015 ...

メーカー Quantum カテゴリー Network Card

Quantum QTM300CAのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- QTM300CAの取扱説明書
- Quantumの製品カード
- パンフレット
- またはQuantum QTM300CAの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Quantum QTM300CAの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Quantum QTM300CAの取り付け説明書、サービスマニュアル、簡易説明書、またはQuantum QTM300CAのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Quantum QTM300CAの製品を使用するにあたって最も人気のある説明書を閲覧できます。

Quantum QTM300CAデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがQuantum QTM300CAを使用するのを助ける技術的文書のことです。説明書は通常、全てのQuantum QTM300CAユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Quantumの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Quantum QTM300CAの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははQuantum QTM300CAの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Quantum QTM300CAに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Quantum QTM300CAデバイスの基本機能を使うにあたってのヒント。 Quantum QTM300CAのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Quantum QTM300CAに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるQuantum QTM300CAのメーカー/サービスへの連絡先に関する情報。

Quantum QTM300CAについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもQuantum QTM300CAの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがQuantum QTM300CAで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)