English dropdown-ico

Manual Quantum QTM300CA

12 pages 0.42 mb
Download

Go to site of 12

Summary
  • Quantum QTM300CA - page 1

    QTM300CA USER'S GUIDE Cloning Adapter for the QT3xx family of QProx™ ICs The QTM300CA is a cloning adapter designed to interface between any QT3xx 8-pin sensor IC (QT300, QT310, QT320) and a PC or other host device. This adapter permits the designer to upload settings from a PC into the target chip or to read the settings inside a chip. The ...

  • Quantum QTM300CA - page 2

    To begin using the board right away 1. Connect the QTM300CA to a PC using the serial cable (included). Make sure the serial port is not being used by any other application or driver. 2. Connect the QTM300CA to the target board’s 10-pin IDC cloning header; the stripe of the cable connects to the pin marked with a white square . 3. Run QT3View on t ...

  • Quantum QTM300CA - page 3

    Figure 1 - Board Layout If a QT3xx chip has been auto-detected, this button will clone Setups data from the QTM300CA to the chip. The ‘PROG’ LED (see next section) indicates the programming result. The QTM300CA can store three sources of data, one for each part type. The correct source will be used to program the detected part. Program Button T ...

  • Quantum QTM300CA - page 4

    Indicates the programming status of the target chip in Stand-alone mode. The PROG LED will light during the cloning process in Stand-alone mode. Afterwards the LED will flash on/off 3 times to indicate completion: Fast flashing: (0.1s between flashes) the clone process was a success. Slow flashing: (1s between flashes) the clone process failed. If ...

  • Quantum QTM300CA - page 5

    Figure 2 - QT3View Screen Restores a config file saved by (File | Save). All three part selector configurations (tabs) will be restored by this action. Saves all three part selector configurations to disk in a single file, to a file name of your choice. Selects the desired PC serial port. Com1 is selected by default when the software is first start ...

  • Quantum QTM300CA - page 6

    The status bar at the bottom shows the serial port and connection status. Possibilities are: Serial Port Status: - Off Line - COM1: 57600 N 8 1 - COM2: 57600 N 8 1 Connection Status: - Status: Clone connected - Status: Clone & QT300 connected - Status: Clone & QT310 connected - Status: Clone & QT320 connected - Status: No Clone Status B ...

  • Quantum QTM300CA - page 7

    Cloning Directly to a Chip You can read and clone back information to a QT3xx chip directly from your PC without involving the onboard stand-alone memory of the QTM300CA. Here’s how.... Refer to the device data sheet and the QT3View help file for more information on Setup issues. Clone the Setups to the chip:  Upload Setups to the chip from th ...

  • Quantum QTM300CA - page 8

    Clone the Setups to the Chip:  Push the PROG button on the board.  The PROG LED will light to indicate programming status.  The PROG LED will flash to indicate the programming result; see page 4. Step 2 Hook everything up:  Connect the QTM300CA’s cloning cable to the target PCB, or insert a QT3xx chip into the onboard socket.  Powe ...

  • Quantum QTM300CA - page 9

    If the Synchronization input is used, a 10K resistor should be used to avoid problems with the cloning process; see Figure 4 below. QT310 Place the connector as close as possible to the chip. Placing the cloning connector far from the part will increase sensor load capacitance Cx and decrease sensitivity, as some of the cloning lines are also sense ...

  • Quantum QTM300CA - page 10

    Figure 5 - QT320 Clone Connections VSS 8 S2A S1A 2 6 3 C S2B S1B 5 C SCK OUT2 7 OUT2 S2 OUT1 4 OUT1 1 VDD Vdd S1 SDO SDI GND Electrode 2 Electrode 1 l q 10 QTM300CA/R1.02 25.09.03 ...

  • Quantum QTM300CA - page 11

    Table 1 - Clone Cable Functional Pinout - Usage by Part N/C N/C N/C 10 SCK SCK SCK 9 Vcc 1 Vcc 1 Vcc 1 8 SDI SDI SDI / REQ 7 SDO SDO SDO 6 N/C N/C N/C 5 N/C N/C N/C 4 N/C N/C DRDY 3 GND GND GND 2 Vcc 1 Vcc 1 Vcc 1 1 QT320 QT310 QT300 Pin Note 1: Vcc is connected via a 1K pullup on QTM300CA board Table 2- Chip ZIF Socket Order Information www.logica ...

  • Quantum QTM300CA - page 12

    l Q Copyright © 2003 QRG Ltd. All rights reserved. Patented and patents pending Corporate Headquarters 1 Mitchell Point Ensign Way, Hamble SO31 4RF Great Britain Tel: +44 (0)23 8056 5600 Fax: +44 (0)23 8045 3939 admin@qprox.com www.qprox.com North America 651 Holiday Drive Bldg. 5 / 300 Pittsburgh, PA 15220 USA Tel: 412-391-7367 Fax: 412-291-1015 ...

Manufacturer Quantum Category Network Card

Documents that we receive from a manufacturer of a Quantum QTM300CA can be divided into several groups. They are, among others:
- Quantum technical drawings
- QTM300CA manuals
- Quantum product data sheets
- information booklets
- or energy labels Quantum QTM300CA
All of them are important, but the most important information from the point of view of use of the device are in the user manual Quantum QTM300CA.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Quantum QTM300CA, service manual, brief instructions and user manuals Quantum QTM300CA. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Quantum QTM300CA.

Similar manuals

A complete manual for the device Quantum QTM300CA, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Quantum QTM300CA by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Quantum QTM300CA.

A complete Quantum manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Quantum QTM300CA - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Quantum QTM300CA, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Quantum QTM300CA, that we can find in the current document
3. Tips how to use the basic functions of the device Quantum QTM300CA - which should help us in our first steps of using Quantum QTM300CA
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Quantum QTM300CA
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Quantum QTM300CA in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Quantum QTM300CA?

Use the form below

If you did not solve your problem by using a manual Quantum QTM300CA, ask a question using the form below. If a user had a similar problem with Quantum QTM300CA it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)