Miele KM2030 en-CAの取扱説明書

18ページ 1.08 mb
ダウンロード

ページに移動 of 18

Summary
  • Miele KM2030 en-CA - page 1

    Installation Instructions KM2030 en-CA IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE To prevent accidents and machine damage read these instructions before installation or use. Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulatio ...

  • Miele KM2030 en-CA - page 2

    To avoid damage to the appliance, it should not be installed until the upper cabinet and exhaust hood have already been mounted. ~ This appliance is not connected to an exhaust vent. It must be installed and connected to the power supply in compliance with the applicable installation requirements. ~ The room will need to be at least 20 m 3 in volum ...

  • Miele KM2030 en-CA - page 3

    Upper clearance For an exhaust hood above the appliance, the safe clearance distance indicated by the hood manufacturer must be maintained. If there are no specifications from the hood manufacturer or if flammable materials (e. g., a hanging cabinet) are installed above the appliance, the clearance distance must be at least 30" (760 mm). The m ...

  • Miele KM2030 en-CA - page 4

    When installing a gas stovetop, the cabinetry or walls to ONE side and to the rear of the appliance can be as tall as you wish. However, on the other side there must not be any appliance or furniture that is taller than the installed gas stovetop (see illustrations). You must ensure that the following minimum safety clearances are kept: – 4" ...

  • Miele KM2030 en-CA - page 5

    KM 2030 a front b Installation height c Gas connection R 1/2" ISO 7-1 d Junction box with power cable ,L=7 8 3 / 4 " (2000 mm) Appliance and installation dimensions 29 ...

  • Miele KM2030 en-CA - page 6

    KM 2050 a front b Installation height c Gas connection R 1/2" ISO 7-1 d Junction box with power cable ,L=7 8 3 / 4 " (2000 mm) Appliance and installation dimensions 30 ...

  • Miele KM2030 en-CA - page 7

    How to make the countertop cut-out ^ Use the template to make a countertop cut-out. Be sure to observe the minimum distance from the rear wall and from the left or right to a side wall . See the section on "SAFETY NOTICES FOR INSTALLATION". ^ Seal any wooden countertop surfaces with a special varnish, silicone rubber, or resin, to help pr ...

  • Miele KM2030 en-CA - page 8

    Sealing NEVER use sealing unless it is explicitly called for in the instructions. The sealing strip under the edge of the upper part of the appliance provides a sufficient seal against the countertop. NEVER use sealing between the upper appliance frame and the countertop! It will hinder access to the appliance during servicing, and the frame and co ...

  • Miele KM2030 en-CA - page 9

    This appliance must be grounded according to local or national codes. All electrical work should be performed by a qualified electrician in accordance with local codes and with the: - National Electrical Code ANSI / NFPA 70 for the USA or - Canadian Electrical Code Part I for Canada (CSA Standard C 22.1) , WARNING Disconnect the appliance from the ...

  • Miele KM2030 en-CA - page 10

    Installation and service must be performed by a qualified installer, service agency or the gas supplier. This appliance must be installed with its own shut off valve and the included gas pressure regulator. Both the valve and the regulator must be easily accessible to the consumer to turn on or shut off the gas supply after the appliance is install ...

  • Miele KM2030 en-CA - page 11

    Gas pressure regulator A pressure regulator that is convertible from natural to LP gas (Propane) or vice versa is included with the appliance. The included regulator corresponds with the gas type of the appliance. Verify before installing. The adjusted pressure is: natural gas - 4" w.c. LP gas - 10" w.c. a Appliance b ½" NPT c Regul ...

  • Miele KM2030 en-CA - page 12

    The appliance should have been ordered for connection to either natural gas or LP gas (propane). If the appliance is not configured for the proper type of gas connection please contact your Miele Dealer. If the appliance is to be connected to a type of gas other than it was originally configured for, both the regulator and burners must be converted ...

  • Miele KM2030 en-CA - page 13

    Rated load at high setting Burner Type of gas KM 2030 KM 2050 BTU/hr kW BTU/hr kW Small burner Natural gas (NG) Liquid gas (LP) 3500 3500 1,00 1,00 3500 3500 1,00 1,00 Regular burner Natural gas (NG) Liquid gas (LP) 6200 5800 1,80 1,70 6200 5800 1,80 1,70 Power burner Natural gas (NG) Liquid gas (LP) - - - - 8900 8900 2,60 2,60 Wok Natural gas (NG) ...

  • Miele KM2030 en-CA - page 14

    , Switchover to a different gas type should only be performed by a duly authorized gas company technician. Save the nozzles removed from the appliance for future use. Nozzle table If you switch to a different type of gas, the large and small burner nozzles will need to be changed. Main nozzle Ø Low setting nozzle Ø Natural gas (NG) Small burner R ...

  • Miele KM2030 en-CA - page 15

    How to change a nozzle Unplug the appliance from the electrical supply. How to change the main nozzle ^ Remove the burner cover b , the burner ring a (wok) and the burner head c . ^ Use a socket wrench (M7) to unscrew the main nozzle h . ^ Insert the proper nozzles (see Nozzle table) and tighten them down. Small, normal, and power burners Wok burne ...

  • Miele KM2030 en-CA - page 16

    How to change the small nozzles (all burners) To change the small nozzles, you will first need to remove the upper part of the appliance. ^ Unscrew the mounting screws on the burner. ^ Pull the control knob up and off. ^ Take off the upper part of the appliance. ^ Remove the ignition switch a . ^ Use a small screwdriver to unscrew the small nozzle ...

  • Miele KM2030 en-CA - page 17

    After switching over ^ Use the reverse order to re-assemble the burner parts. ^ Before putting the upper part of the appliance back in place, light each burner with matches to test the seal on all the gas flow parts. ^ After testing, set aside the loose burner parts. ^ Put the upper part of the appliance back in place. ^ Screw down the lower part o ...

  • Miele KM2030 en-CA - page 18

    Alteration rights reserved / 4908 For the most updated manual see the Miele web site. M.-Nr. 07 520 080 / 00 ...

メーカー Miele カテゴリー Welding Consumables

Miele KM2030 en-CAのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- KM2030 en-CAの取扱説明書
- Mieleの製品カード
- パンフレット
- またはMiele KM2030 en-CAの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Miele KM2030 en-CAの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Miele KM2030 en-CAの取り付け説明書、サービスマニュアル、簡易説明書、またはMiele KM2030 en-CAのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Miele KM2030 en-CAの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Miele KM2030 en-CAデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMiele KM2030 en-CAを使用するのを助ける技術的文書のことです。説明書は通常、全てのMiele KM2030 en-CAユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Mieleの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Miele KM2030 en-CAの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMiele KM2030 en-CAの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Miele KM2030 en-CAに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Miele KM2030 en-CAデバイスの基本機能を使うにあたってのヒント。 Miele KM2030 en-CAのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Miele KM2030 en-CAに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMiele KM2030 en-CAのメーカー/サービスへの連絡先に関する情報。

Miele KM2030 en-CAについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMiele KM2030 en-CAの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMiele KM2030 en-CAで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)