Porter-Cable MODEL 7310の取扱説明書

25ページ 0.3 mb
ダウンロード

ページに移動 of 25

Summary
  • Porter-Cable MODEL 7310 - page 1

    Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...

  • Porter-Cable MODEL 7310 - page 2

    T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property ...

  • Porter-Cable MODEL 7310 - page 3

    Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry produ ...

  • Porter-Cable MODEL 7310 - page 4

    Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS 1) Work area safety a) Keep work are ...

  • Porter-Cable MODEL 7310 - page 5

    d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose cl ...

  • Porter-Cable MODEL 7310 - page 6

    6 ADDITIONAL SPECIFIC SAFETY RULES 1. HOLD POWER TOOLS BY INSULATED GRIPPING SURFACES WHEN PERFORMING AN OPERATION WHERE THE CUTTING TOOL MAY CONTACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2 . USE CLAMPS OR OTHER PRACTICAL WAY TO SECURE A ...

  • Porter-Cable MODEL 7310 - page 7

    7 NOTES ...

  • Porter-Cable MODEL 7310 - page 8

    8 SAVE THESE INSTRUCTIONS! SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g .................... ...

  • Porter-Cable MODEL 7310 - page 9

    9 If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amp ...

  • Porter-Cable MODEL 7310 - page 10

    10 FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable Laminate Trimmers are designed for flush and bevel trimming laminated plastics, phenolics, and other similar materials having a bonding agent too hard to be trimmed with ordinary tools. The Tilt-Base model allows trimming into corners inaccessible to standard trimmers and to trim laminated surfaces jo ...

  • Porter-Cable MODEL 7310 - page 11

    11 TO AVOID PERSONAL INJURY OR DAMAGE TO FINISHED WORK ALWAYS ALLOW THE MOTOR TO COME TO A COMPLETE STOP BEFORE SETTING TRIMMER DOWN. TO INST ALL BIT DISCONNECT TOOL FROM POWER SOURCE. 1. On Models 7310 and 7319 bits may be installed with the motor unit either assembled or removed from the base. See instructions under Model 7312 for installing the ...

  • Porter-Cable MODEL 7310 - page 12

    ADJUSTING DEPTH OF CUT DISCONNECT TOOL FROM POWER SOURCE. 1. Loosen base locking screw (Fig. 3) approximately one-quarter turn. 2. Turn depth adjusting wheel (Fig. 3) clockwise, looking at top of wheel, to raise cutter reducing depth of cut or counterclockwise to lower cutter for increasing depth of cut. 3. Tighten base locking screw securely and m ...

  • Porter-Cable MODEL 7310 - page 13

    13 ASSEMBLING AND ADJUSTING BASE AND ROLLER GUIDE 1. Remove power unit from base unit (see “TO INSTALL BIT”), and install the bit. 2. The base and roller guide (A) Fig. 4, is assembled at the factory. To assemble, remove a sub-base mounting screw (A) Fig. 5 and insert alignment pin in guide base into hole (C) in bottom of trimmer sub-base. Fast ...

  • Porter-Cable MODEL 7310 - page 14

    14 5. Remove guide setting gauge from trimmer and install flush trimming bit. 6. Adjust depth of cut so that the straight portion of the bit extends below the trimmer base at least the thickness of the material to be trimmed. 7. Make a trial cut on scrap material. Readjust if necessary. BEVEL TRIMMING 1. Follow Steps 1 through 5 under FLUSH TRIMMIN ...

  • Porter-Cable MODEL 7310 - page 15

    15 be sure at least 1 / 2 " of bit shank is engaged in collet. Do not use bits that result in having less than 1 / 2 " of bit shank engaged in collet. To do so may cause poor gripping of collet resulting in loose bit and damage to work, or personal injury should the bit come out of collet. ADJUSTING TIL T 1. Loosen two tilt locking screws ...

  • Porter-Cable MODEL 7310 - page 16

    16 TO INST ALL & REMOVE BIT DISCONNECT TOOL FROM POWER SOURCE. 1 . Insert long portion of hex wrench (furnished) through spindle lock hole (see Fig. 10) so that wrench protrudes from both sides of base housing. It may be necessary to rotate spindle by hand to align hole in spindle with holes in housing. 2 . Clean and insert bit shank into colle ...

  • Porter-Cable MODEL 7310 - page 17

    17 3. DISCONNECT TOOL FROM POWER SOURCE. 4 . Firmly grasp motor housing being sure switch is in the “OFF” position. 5. Verify bit is clear of foreign objects and cord will not “hang up” on any obstructions. 6. Be sure workpiece is firmly held in place. Use clamps where necessary to secure workpiece. 7. Plug in power supply cord. Be alert to ...

  • Porter-Cable MODEL 7310 - page 18

    18 UNDERSCRIBE 7320 TRIMMER ASSEMBL Y The Underscribe Trimmer Base is assembled to the Model 7301 Trimmer Motor as follows: NOTE: The 43109 Trim Bit must be installed into the Trimmer Motor before attaching the motor to the Underscribe Base. DISCONNECT TOOL FROM POWER SOURCE. 1. Clean and insert shank of bit (A) Fig. 14, into collet until end of sh ...

  • Porter-Cable MODEL 7310 - page 19

    19 bottoms. Then pull bit out approximately 1 / 8 ". 2 . Depress spindle lock (B) Fig. 14, and rotate collet nut (C) clockwise by hand until lock engages hole in motor spindle. 3 . While holding spindle lock engaged, tighten collet nut securely by turning clockwise using wrench provided. NEVER TIGHTEN COLLET WITHOUT BIT INSERTED, TO DO SO MAY ...

  • Porter-Cable MODEL 7310 - page 20

    20 If joint to TOO TIGHT (laminate will not snap into place), turn eccentric counterclockwise. 4. Repeat Steps 1 through 3 as required to achieve a good fit- up. USING THE UNDERSCRIBE TRIMMER The bottom plate of the Underscribe Trimmer has a guide lip (see Fig. 17). This guide lip is moved along an installed piece of laminate as the trimmer bit cut ...

  • Porter-Cable MODEL 7310 - page 21

    21 5. Position the underscribe trimmer onto the face frame so that the top (see Fig. 19), is against the edge of the stile. NOTE: The trimmer should be to the right of the rail, so that the cutting action will move from right to left (see Fig. 19). 6. Verify that bit is clear of foreign objects and that cord will not hang on any obstructions. 7. Gr ...

  • Porter-Cable MODEL 7310 - page 22

    22 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. F AILURE TO ST ART Should your tool fail t ...

  • Porter-Cable MODEL 7310 - page 23

    23 SERVICE REPLACEMENT P ARTS When servicing use only identical replacement parts. SERVICE AND REP AIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations, including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED PORTER- CABLE SERVICE STATION ...

  • Porter-Cable MODEL 7310 - page 24

    24 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material du ...

  • Porter-Cable MODEL 7310 - page 25

    The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...

メーカー Porter-Cable カテゴリー Laminate Trimmer

Porter-Cable MODEL 7310のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- MODEL 7310の取扱説明書
- Porter-Cableの製品カード
- パンフレット
- またはPorter-Cable MODEL 7310の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Porter-Cable MODEL 7310の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Porter-Cable MODEL 7310の取り付け説明書、サービスマニュアル、簡易説明書、またはPorter-Cable MODEL 7310のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Porter-Cable MODEL 7310の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Porter-Cable MODEL 7310デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPorter-Cable MODEL 7310を使用するのを助ける技術的文書のことです。説明書は通常、全てのPorter-Cable MODEL 7310ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Porter-Cableの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Porter-Cable MODEL 7310の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPorter-Cable MODEL 7310の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Porter-Cable MODEL 7310に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Porter-Cable MODEL 7310デバイスの基本機能を使うにあたってのヒント。 Porter-Cable MODEL 7310のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Porter-Cable MODEL 7310に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPorter-Cable MODEL 7310のメーカー/サービスへの連絡先に関する情報。

Porter-Cable MODEL 7310についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPorter-Cable MODEL 7310の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable MODEL 7310で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)