Pitco L80-029の取扱説明書

24ページ 2.74 mb
ダウンロード

ページに移動 of 24

Summary
  • Pitco L80-029 - page 1

    L80-029 Rev 5 10/07 IMPORTANT FOR FUTURE REF ERENCE Please complete this information and retain these instructions for the life of the equipmen t: Model #: ___________ ___________ ____ Serial #: ___________ ___________ ____ Date Upgraded: ___________ ________ Technician: _________________________ Installation Instructions for the PITCO Self-Cleanin ...

  • Pitco L80-029 - page 2

    L80-029 Rev 5 10/07 WARNING Drain the tank and ensure that appliance has cooled to room temperature before performing this upgrade. DO NOT work on a hot appliance or an appliance containing hot cooking medium; serious personal injury may occur. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE TO THE PURCHASER Post in a prominent location t he instruc ...

  • Pitco L80-029 - page 3

    1 L80-029 Rev 5 10/0 7 Theory of Operation : A natural gas burning applian ce requires roughly 10 cubic feet of air to properly combust a singl e cubic foot of gas. Minute airborne particles ent rained during this process pass t hrough the combustion sy stem and are incinerated. However, some particl es may be trapped within t he combustion system, ...

  • Pitco L80-029 - page 4

    L80-029 Rev 5 10/07 2 Follow this procedure for Inst allation of Self Cleaning burners and SCBS arm: a. Disconnect the control harne ss from the main gas valve and tuck it out the way to avoid damaging the harness during this procedure. b. If your appliance has a solid -state control (or auxiliary thermostat) behind t he door, remove it at this tim ...

  • Pitco L80-029 - page 5

    3 L80-029 Rev 5 10/07 e. Using a 1 1/16” wrench and a 7/8” wrench, loosen the brass fitting on the top of t he gas valve and disconnect the gas valve from the manifold inlet. This will allow you to drop the ga s valve down and keep it out of the way during burner replacement. f. Using a 5/16” wrench, nut drive r or screw gun bit, remove all b ...

  • Pitco L80-029 - page 6

    L80-029 Rev 5 10/07 4 i. Captu re the remaining burners on the SCBS Arm in the same manner as in step h, an d secure them into the appliance, taking care not t o strip the pre-threaded holes. j. Secu re the SCBS Arm to left side of the burner to the right of the pilot using two 10 X 24 self-threading screws provided with the Pitco Self -Cleaning Bu ...

  • Pitco L80-029 - page 7

    5 L80-029 Re v 5 10/07 NOTE: CE approved models will h ave a pressure test fitting in this location. For CE app roved models, remove this pressure test fitting using a 7/16” (12 mm) wrench. Using a 3/16” (5 mm) hex key, re move the plug from the auxiliary pressure tap on the m anifold inlet and replace it with pressure tap fitting that you remo ...

  • Pitco L80-029 - page 8

    L80-029 Rev 5 10/07 6 e. Thread the compression nut on the corrugated tubing end of the SCBS Valve Assembly onto the orifice assembly that you inserted int o the runner tube in step c and tighten with a 1/2” ( 13 mm) wrench. f. Install the orifice retainer brac ket onto the pilot bracket and SCBS Orifice assembly . This will secure the orifice as ...

  • Pitco L80-029 - page 9

    7 L80-029 Rev 5 10/ 07 b. Disconnect the wiring harne ss from the relay board mounted behind the front panel and remove the relay board and insulation pape r. Be sure to retain the screws. The existing relay boa rd may or may not have a jumper plug as shown. If it does, remove it from the old relay board and in stall it into the same position on th ...

  • Pitco L80-029 - page 10

    L80-029 Rev 5 10/07 8 e. If the appliance you are upg rading does NOT have a Solid State Control, proceed to step f in this section. If the appliance that you are up grading has a Solid State Control, feed the other en ds of the SCBS Harness through the unused po rtion of the strain relief holding the Solid State Co ntrol Harness and proceed direct ...

  • Pitco L80-029 - page 11

    9 L80-029 Rev 5 10/ 07 i. Conne ct the SCBS Harness to the SCBS Valve as shown. The red and violet wires m ust be connected to the vertically oriented tabs on the valve and the green (ground) wire must be connected to the bottom, horizontally oriented tab o n the valve. The grey wires will be connected to the T hermal Limit at a later point in the ...

  • Pitco L80-029 - page 12

    L80-029 Rev 5 10/07 10 Follow this procedure to che ck proper operation of the Pi tco Self-Cleaning Burner System: WARNING Ensure that tank is filled to t he level line with oil before turning the appliance on. Turning the ap pliance on with an empty or partially filled tank could cause an unsafe condition, which could lead to d amage to the applia ...

  • Pitco L80-029 - page 13

    11 L80-029 Rev 5 10/0 7 appliance is in operation, or ca n be detected visually by watching t he burner flame through the air collars. The sound of the burners will be inc onsistent and the flame may ap pear to ‘peel’ off of the burner fa ce. A certain amount of flame roll o ut during ignition is normal. Howeve r, excessive flame roll out du ri ...

  • Pitco L80-029 - page 14

    L80-029 Re v 5 10/07 12 PROBLEM A . Main breaker in OFF p osition. A . Turn on Circuit Breaker to appliance. B. Gas supply turned OFF. B. Turn on gas supply to appliance. C. A ppliance unplugged. C. Plug appliance pow er cord into wall ou tlet. D. Blown con trol fuse. D. E. Faulty transformer. E. F. Defectiv e controller. F. A . Tripped hi limit A ...

  • Pitco L80-029 - page 15

    13 L80-029 Rev 5 10/ 07 ...

  • Pitco L80-029 - page 16

    L80-029 Rev 5 10/07 14 ...

  • Pitco L80-029 - page 17

    15 L80-029 Rev 5 10/ 07 ...

  • Pitco L80-029 - page 18

    L80-029 Rev 5 10/07 16 ...

  • Pitco L80-029 - page 19

    17 L80-029 Rev 5 10/07 ...

  • Pitco L80-029 - page 20

    L80-029 Rev 5 10/07 18 ...

  • Pitco L80-029 - page 21

    19 L80-029 Rev 5 10/07 ...

  • Pitco L80-029 - page 22

    L80-029 Rev 5 10/07 20 ...

  • Pitco L80-029 - page 23

    21 L80-029 Rev 5 10/07 Before and After: Visual Aid The below images show a typical m odel SG14 burner assembly before and after the installation of the SCBS upgrade. Wire harnesses and pilot tubing are omitted to provide bet ter clarity. In order to give the installer a sense of part orientation and l ocation, the gas piping parts (valv e, tubing, ...

  • Pitco L80-029 - page 24

    MAILING ADDRESS – P. O. BOX 501, CONCORD, NH 033 02-0501 SHIPPING ADDRESS – 10 FE RRY ST., CONCORD, NH 03 301 In th e eve nt of prob lem s wit h or qu est ion s abo ut you r orde r, plea se conta ct the Pitc o Frial ato r fa cto ry at : (80 0) 25 8- 370 8 U S and Ca nad a o nl y o r (60 3) 22 5- 668 4 W or ld W id e In the even t of pro ble ms ...

メーカー Pitco カテゴリー Burner

Pitco L80-029のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- L80-029の取扱説明書
- Pitcoの製品カード
- パンフレット
- またはPitco L80-029の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Pitco L80-029の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Pitco L80-029の取り付け説明書、サービスマニュアル、簡易説明書、またはPitco L80-029のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Pitco L80-029の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Pitco L80-029デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPitco L80-029を使用するのを助ける技術的文書のことです。説明書は通常、全てのPitco L80-029ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Pitcoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Pitco L80-029の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPitco L80-029の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Pitco L80-029に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Pitco L80-029デバイスの基本機能を使うにあたってのヒント。 Pitco L80-029のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Pitco L80-029に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPitco L80-029のメーカー/サービスへの連絡先に関する情報。

Pitco L80-029についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPitco L80-029の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPitco L80-029で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)