English dropdown-ico

Manual Pitco L80-029

24 pages 2.74 mb
Download

Go to site of 24

Summary
  • Pitco L80-029 - page 1

    L80-029 Rev 5 10/07 IMPORTANT FOR FUTURE REF ERENCE Please complete this information and retain these instructions for the life of the equipmen t: Model #: ___________ ___________ ____ Serial #: ___________ ___________ ____ Date Upgraded: ___________ ________ Technician: _________________________ Installation Instructions for the PITCO Self-Cleanin ...

  • Pitco L80-029 - page 2

    L80-029 Rev 5 10/07 WARNING Drain the tank and ensure that appliance has cooled to room temperature before performing this upgrade. DO NOT work on a hot appliance or an appliance containing hot cooking medium; serious personal injury may occur. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE TO THE PURCHASER Post in a prominent location t he instruc ...

  • Pitco L80-029 - page 3

    1 L80-029 Rev 5 10/0 7 Theory of Operation : A natural gas burning applian ce requires roughly 10 cubic feet of air to properly combust a singl e cubic foot of gas. Minute airborne particles ent rained during this process pass t hrough the combustion sy stem and are incinerated. However, some particl es may be trapped within t he combustion system, ...

  • Pitco L80-029 - page 4

    L80-029 Rev 5 10/07 2 Follow this procedure for Inst allation of Self Cleaning burners and SCBS arm: a. Disconnect the control harne ss from the main gas valve and tuck it out the way to avoid damaging the harness during this procedure. b. If your appliance has a solid -state control (or auxiliary thermostat) behind t he door, remove it at this tim ...

  • Pitco L80-029 - page 5

    3 L80-029 Rev 5 10/07 e. Using a 1 1/16” wrench and a 7/8” wrench, loosen the brass fitting on the top of t he gas valve and disconnect the gas valve from the manifold inlet. This will allow you to drop the ga s valve down and keep it out of the way during burner replacement. f. Using a 5/16” wrench, nut drive r or screw gun bit, remove all b ...

  • Pitco L80-029 - page 6

    L80-029 Rev 5 10/07 4 i. Captu re the remaining burners on the SCBS Arm in the same manner as in step h, an d secure them into the appliance, taking care not t o strip the pre-threaded holes. j. Secu re the SCBS Arm to left side of the burner to the right of the pilot using two 10 X 24 self-threading screws provided with the Pitco Self -Cleaning Bu ...

  • Pitco L80-029 - page 7

    5 L80-029 Re v 5 10/07 NOTE: CE approved models will h ave a pressure test fitting in this location. For CE app roved models, remove this pressure test fitting using a 7/16” (12 mm) wrench. Using a 3/16” (5 mm) hex key, re move the plug from the auxiliary pressure tap on the m anifold inlet and replace it with pressure tap fitting that you remo ...

  • Pitco L80-029 - page 8

    L80-029 Rev 5 10/07 6 e. Thread the compression nut on the corrugated tubing end of the SCBS Valve Assembly onto the orifice assembly that you inserted int o the runner tube in step c and tighten with a 1/2” ( 13 mm) wrench. f. Install the orifice retainer brac ket onto the pilot bracket and SCBS Orifice assembly . This will secure the orifice as ...

  • Pitco L80-029 - page 9

    7 L80-029 Rev 5 10/ 07 b. Disconnect the wiring harne ss from the relay board mounted behind the front panel and remove the relay board and insulation pape r. Be sure to retain the screws. The existing relay boa rd may or may not have a jumper plug as shown. If it does, remove it from the old relay board and in stall it into the same position on th ...

  • Pitco L80-029 - page 10

    L80-029 Rev 5 10/07 8 e. If the appliance you are upg rading does NOT have a Solid State Control, proceed to step f in this section. If the appliance that you are up grading has a Solid State Control, feed the other en ds of the SCBS Harness through the unused po rtion of the strain relief holding the Solid State Co ntrol Harness and proceed direct ...

  • Pitco L80-029 - page 11

    9 L80-029 Rev 5 10/ 07 i. Conne ct the SCBS Harness to the SCBS Valve as shown. The red and violet wires m ust be connected to the vertically oriented tabs on the valve and the green (ground) wire must be connected to the bottom, horizontally oriented tab o n the valve. The grey wires will be connected to the T hermal Limit at a later point in the ...

  • Pitco L80-029 - page 12

    L80-029 Rev 5 10/07 10 Follow this procedure to che ck proper operation of the Pi tco Self-Cleaning Burner System: WARNING Ensure that tank is filled to t he level line with oil before turning the appliance on. Turning the ap pliance on with an empty or partially filled tank could cause an unsafe condition, which could lead to d amage to the applia ...

  • Pitco L80-029 - page 13

    11 L80-029 Rev 5 10/0 7 appliance is in operation, or ca n be detected visually by watching t he burner flame through the air collars. The sound of the burners will be inc onsistent and the flame may ap pear to ‘peel’ off of the burner fa ce. A certain amount of flame roll o ut during ignition is normal. Howeve r, excessive flame roll out du ri ...

  • Pitco L80-029 - page 14

    L80-029 Re v 5 10/07 12 PROBLEM A . Main breaker in OFF p osition. A . Turn on Circuit Breaker to appliance. B. Gas supply turned OFF. B. Turn on gas supply to appliance. C. A ppliance unplugged. C. Plug appliance pow er cord into wall ou tlet. D. Blown con trol fuse. D. E. Faulty transformer. E. F. Defectiv e controller. F. A . Tripped hi limit A ...

  • Pitco L80-029 - page 15

    13 L80-029 Rev 5 10/ 07 ...

  • Pitco L80-029 - page 16

    L80-029 Rev 5 10/07 14 ...

  • Pitco L80-029 - page 17

    15 L80-029 Rev 5 10/ 07 ...

  • Pitco L80-029 - page 18

    L80-029 Rev 5 10/07 16 ...

  • Pitco L80-029 - page 19

    17 L80-029 Rev 5 10/07 ...

  • Pitco L80-029 - page 20

    L80-029 Rev 5 10/07 18 ...

  • Pitco L80-029 - page 21

    19 L80-029 Rev 5 10/07 ...

  • Pitco L80-029 - page 22

    L80-029 Rev 5 10/07 20 ...

  • Pitco L80-029 - page 23

    21 L80-029 Rev 5 10/07 Before and After: Visual Aid The below images show a typical m odel SG14 burner assembly before and after the installation of the SCBS upgrade. Wire harnesses and pilot tubing are omitted to provide bet ter clarity. In order to give the installer a sense of part orientation and l ocation, the gas piping parts (valv e, tubing, ...

  • Pitco L80-029 - page 24

    MAILING ADDRESS – P. O. BOX 501, CONCORD, NH 033 02-0501 SHIPPING ADDRESS – 10 FE RRY ST., CONCORD, NH 03 301 In th e eve nt of prob lem s wit h or qu est ion s abo ut you r orde r, plea se conta ct the Pitc o Frial ato r fa cto ry at : (80 0) 25 8- 370 8 U S and Ca nad a o nl y o r (60 3) 22 5- 668 4 W or ld W id e In the even t of pro ble ms ...

Manufacturer Pitco Category Burner

Documents that we receive from a manufacturer of a Pitco L80-029 can be divided into several groups. They are, among others:
- Pitco technical drawings
- L80-029 manuals
- Pitco product data sheets
- information booklets
- or energy labels Pitco L80-029
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pitco L80-029.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pitco L80-029, service manual, brief instructions and user manuals Pitco L80-029. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pitco L80-029.

Similar manuals

A complete manual for the device Pitco L80-029, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pitco L80-029 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pitco L80-029.

A complete Pitco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pitco L80-029 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pitco L80-029, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pitco L80-029, that we can find in the current document
3. Tips how to use the basic functions of the device Pitco L80-029 - which should help us in our first steps of using Pitco L80-029
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pitco L80-029
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pitco L80-029 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pitco L80-029?

Use the form below

If you did not solve your problem by using a manual Pitco L80-029, ask a question using the form below. If a user had a similar problem with Pitco L80-029 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)