ADTRAN Protection Switchの取扱説明書

9ページ 0.57 mb
ダウンロード

ページに移動 of 9

Summary
  • ADTRAN Protection Switch - page 1

    1 TRA CER Monitor ed Protection Switch (MPS) Before you begin...  Required Components • (2) TRACER Baseband Proc essor (BBP) and RF Conver ter (RFC) rackmount units Or , • (2) TRACER 4103 or 4203 int egrated rackmount radio units • RS-232 interface cable and VT100 term inal (or a PC with VT 100 emulator software) fo r connecting to the uni ...

  • ADTRAN Protection Switch - page 2

    2 1 Rackmount the Unit s Install the TRACER MPS system in a location that requi res minimal antenna feedline length (the loss in this cable directly af fe cts overall system performance). The TRACER M PS should be mounted in a rack between the tw o BBP component s of the TRACER systems (see Figure 1 on page 2) . Although no space is needed between ...

  • ADTRAN Protection Switch - page 3

    3 2 Creating the VT100 Chain A single VT100 connec tion through the TRACER MPS provides access to bo th the primary (MAIN) and SECONDARY TRACER units. Follow the steps below to create the VT100 chain. 1. Connect the RS-232 port (D B-25) on the rear p anel of the MAIN TRACER BBP to the TRACER MPS VT1 00 interface (labeled 1 on the figure below) usin ...

  • ADTRAN Protection Switch - page 4

    4 2 8 10 4 5 6 9 1 7 4 Reviewing the Menus The TRACER MPS software interface consis t s of a single menu screen (s hown below). Navigate through the available menu options using the up and down arrow ke ys. Alternately , the numbered m enu options may be selected by en tering the appropriate menu numbe r displayed to the left of the opt ion. Pressi ...

  • ADTRAN Protection Switch - page 5

    5 MANAGEMENT T R A C E R MAIN STANDBY OUT NO COM NC MN COM SB IN ALARMS DC POWER RF ANTENNA TO DTE RS-232 MONITOR T1B T1A MAIN TRACER ST ANDBY TRACER MONITOR POWER MODULE USE COPPER CONDUCTORS ONL Y MAIN OUT IN IN OUT B A B A STAND BY T1B T1A TRACER MPS T1A/T1B Interfaces TRACER MPS MAIN T1A Interface 6 4 2 5 5 Connecting the T1 Interfaces 1. Conne ...

  • ADTRAN Protection Switch - page 6

    6 MANAGEMENT T1B T1A IF ANTENNA T R A C E R MAIN STANDBY OUT NO COM NC MN COM SB IN ALARMS DC POWER RF ANTENNA TO DTE RS-232 MONITOR T1B T1A MAIN TRACER ST ANDBY TRACER MONITOR POWER MODULE USE COPPER CONDUCTORS ONL Y OUT IN IN OUT B A B A MAIN STAND BY 2 5 6 TRACER MPS Antenna Interface TRACER MPS ST ANDBY Antenna Interface TRACER MPS MAIN Antenna ...

  • ADTRAN Protection Switch - page 7

    7 6b Connecting the Antenna Interface s (TRACER 4103 and 4203 Systems) 1. Connect the Antenna interface (N-T ype connector) of the MA IN TRACER 4103/4203 (label ed 1 below) to the MA IN RF interface (SMA connector) of the TRACER MPS (labeled 2 below) using a male N-T ype to male SMA cable. 2. Repeat S tep 1 to connect the An tenna interface (N-T yp ...

  • ADTRAN Protection Switch - page 8

    8 7 Connecting the Alarm Cont act s 1. Connect the NO (Norma lly Open) alarm contact of the MAIN TRACER BBP (labeled 1 belo w) to the MN alarm c ontact in the IN alarm block of the TRACER MPS (l abeled 2 below). The TRACER BBP provides two sets of alarm contact s; for no rmal configuration, use the NO located in the MAJ (Major Alarm) block. 2. Conn ...

  • ADTRAN Protection Switch - page 9

    9 8 Supplying Power to the Unit The TRACER MPS can operate from a supply between 21 and 63 V olts DC, with either polarity referenced to ground, and consumes 3 W atts nominal, 20 W a tts peak (during relay switching). Curr ent required (in Amp s) is determined by dividi ng the power consume d (in W att s) by the applied voltage (in V olts). As an e ...

メーカー ADTRAN カテゴリー Network Card

ADTRAN Protection Switchのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Protection Switchの取扱説明書
- ADTRANの製品カード
- パンフレット
- またはADTRAN Protection Switchの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、ADTRAN Protection Switchの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、ADTRAN Protection Switchの取り付け説明書、サービスマニュアル、簡易説明書、またはADTRAN Protection Switchのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、ADTRAN Protection Switchの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

ADTRAN Protection Switchデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがADTRAN Protection Switchを使用するのを助ける技術的文書のことです。説明書は通常、全てのADTRAN Protection Switchユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

ADTRANの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. ADTRAN Protection Switchの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははADTRAN Protection Switchの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。ADTRAN Protection Switchに関してこのドキュメントで見つけることができる全てのヒントの目次
3. ADTRAN Protection Switchデバイスの基本機能を使うにあたってのヒント。 ADTRAN Protection Switchのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。ADTRAN Protection Switchに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるADTRAN Protection Switchのメーカー/サービスへの連絡先に関する情報。

ADTRAN Protection Switchについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもADTRAN Protection Switchの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがADTRAN Protection Switchで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)