-
Bogen & WV250 - page 1
W all-Mount Power V ector Amplifiers WV100, WV150, & WV250 Models Inst allation and Use Manual © 2002 Bogen Communications, Inc. All rights reserved. Specifications subject to change without notice. 54-2086-0 1 B 0304 Printed in K orea. ...
-
Bogen & WV250 - page 2
Notice Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing. How ev er , information is subject to change. Important Safety Information W ARNING: T o Reduce The Risk of Fire Or Electric Shock, Do Not Expose This Apparatus T o Rain Or Moisture. Alwa ys follow these basic safety pr ecaut ...
-
Bogen & WV250 - page 3
Contents Page P ANEL DESCRIPTIONS..................................................................................................2-3 W all-Mount P ow er V ector Front Panel ..........................................................................................2 W all-Mount P ow er V ector Module Ba y (Rear) .................................... ...
-
Bogen & WV250 - page 4
P anel Descriptions W all-Mount Po wer V ector Fr ont P anel 1 . Input V olume Control Each of the 8 module ba ys are controlled b y an independent v olume contr ol. 2. Signal / Clip Indicator A single two-color LED located abov e each channel’ s volume control indicates the audio activity of that chan- nel’ s input. Green indicates signal acti ...
-
Bogen & WV250 - page 5
P anel Descriptions W all-Mount Po wer V ector Module Bay (Rear) 1 . Module Ba ys The amplifier has eight module ba ys, all of which can accommodate input modules, with two ba ys (ba ys 7 and 8) that can accommodate either input or output modules. 2. Lo w-Cut Switch Slide switch (located in module ba y 6) allows roll off of fr equencies below 1 25 ...
-
Bogen & WV250 - page 6
Installation P ackage Contents • Amplifier • 2 Cables • Instruction Manual • Combined XLR receptacle and phone jack • 2 Scre ws (M 3 x 8) • 6 Scre ws (M 4 x 8) Mounting A surface-mount (model BBS) or flush-mount (model BBF shown below) back bo x as w ell as a WMAD door is requir ed for installation. Refer to the instructions pr ovided w ...
-
Bogen & WV250 - page 7
Modules Module Installation Eight module ba ys are a vailable to accept Bogen’ s new advanced plug-in input modules. Module ba ys 7 & 8 can also accommodate Bogen’ s new advanced plug-in output modules, thereby allo wing users to customize the amplifier to suit the needs of the installation. (Note: The ba ys will not accept Bogen’ s older ...
-
Bogen & WV250 - page 8
Connections Speakers T ransf ormer -Coupled Speaker Connections T ransf ormer -coupled, constant voltage speak er loads are connected to their respectiv e load type (i.e ., 70V speak ers to the 70V terminal, 25V speak er systems to the 25V terminals) and the COM terminal. Make sur e the selector switch is in the TRANS OUT position. A separate 8-ohm ...
-
Bogen & WV250 - page 9
Connections COM and GND T erminals A shorting jumper typically connects the COM and GND terminals of the amplifier together . The COM terminal is a common lead from the output transformer . For the transf ormer -coupled speaker output to work, one of the speaker load leads must be connected to this terminal. The GND terminal is a connection to the ...
-
Bogen & WV250 - page 10
Operation Fr ont P anel Controls & Indicators Input V olume Contr ols Each input module ma y be individually controlled by its cor r esponding volume contr ol knob. Signal / Clip Indicator A single LED located above each channel’ s volume contr ol indicates the audio activity of that channel’ s input. Green indicates signal is being applied ...
-
Bogen & WV250 - page 11
Operation Output Limiter The Output Limiter control sets the thr eshold at which the unit hard limits the output signal. Once the Limiter's threshold is exceeded, the output signal is pre vented from incr easing any further . With the control set to the Min position (fully counter clockwise), the Limiter will pro- vide almost no limiting and i ...
-
Bogen & WV250 - page 12
Block Dia gram 10 ...
-
Bogen & WV250 - page 13
Specifications 11 P o wer Output (RMS): WV 1 00: 1 00W ( 1 40W T ypical, @ 1 kHz/0. 1% /4 Ω) WV 1 50: 1 50W (200W T ypical, @ 1 kHz/0. 1% /4 Ω) WV250: 250W (340W T ypical, @ 1 kHz/0. 1% /4 Ω) Fr equency Response T ransf ormer : 45-20 kHz; 0/-2 dB @ FRP Direct: 20-20 kHz; 0/- 1 dB @ FRP Distortion T ransf ormer : 0.5% THD+N, Maximum, Full-rate ...
-
Bogen & WV250 - page 14
T r oubleshooting 12 • Amplifier not plugged in. • A C outlet dead. • Po w er switch off. • Circuit br eaker tripped. • Speak er connections on amplifier ar e incorr ect. • T rans / Direct Out selector not set corr ectly . • Poor / br oken speak er wiring. • Defectiv e speak ers. • Poor electrical connections at input. • Input c ...
-
Bogen & WV250 - page 15
W arranty 13 Bogen W all-Mount Pow er V ector Amplifiers, modules, and components ar e warranted to be fr ee fr om defects in mate- rial or workmanship pr ovided that the product has not been subjected to abuse or accident or alter ed in any wa y for three (3) y ears from the date of sale to the original pur chaser with the exception of the remote ...
-
Bogen & WV250 - page 16
50 S pring S treet, Ramsey , NJ 07446, U.S.A. T el. 201-934-8500, Fax: 201-934-9832, www .bogen.com ...
Bogen & WV250についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもBogen & WV250の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBogen & WV250で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。